Raltron Electronics Corporation 10651 NW 19th St. Miami, Florida 33172 U.S.A.
Tel: 305-593-6033 Fax: 305-594-3973 e-mail: sales@raltron.com Internet: http://www.raltron.com
35
THROUGH HOLE CLOCK OSCILLATORS - TTL COMPATIBLE
SERIES CO1 AND CO13
SERIES
CO1
CO13
PACKAGE
14 PIN DIP
8 PIN DIP
FREQUENCY RANGE
500.00 KHz TO 125.00 MHz
500.00 KHz TO 125.00 MHz
FREQUENCY STABILITY
CO1100 : 100 ppm
CO13100 : 100 ppm
CO1050 : 50 ppm
CO13050 : 50 ppm
CO1025 : 25 ppm
CO13025 : 25 ppm
OPERATING TEMPERATURE RANGE
0 C TO +70 C STANDARD
-40 C TO +85 C EXTENDED
0 C TO +70 C STANDARD
-40 C TO +85 C EXTENDED
STORAGE TEMPERATURE RANGE
-55 C TO +125 C
-55 C TO +125 C
INPUT
VOLTAGE
+5 VDC 0.5 VDC
+5 VDC 0.5 VDC
CURRENT (MAX)
500.00 KHz TO 2.999 MHz: 30 mA
500.00 KHz TO 2.999 MHz: 30 mA
3.00 MHz TO 31.999 MHz: 50 mA
3.00 MHz TO 31.999 MHz: 50 mA
32.00 MHz TO 79.999 MHz: 70 mA
32.00 MHz TO 79.999 MHz: 70 mA
80.00 MHz TO 125.00 MHz: 80 mA
80.00 MHz TO 125.00 MHz: 80 mA
OUTPUT
SYMMETRY
(AT 1.4 VDC LEVEL)
40 TO 60% NORMAL
45 TO 55% TIGHT
40 TO 60% NORMAL
45 TO 55% TIGHT
RISE AND FALL TIME
(0.4 - 2.4 VDC)
UNDER 9 MHz : 15 ns MAX
UNDER 9 MHz : 15 ns MAX
9 MHz TO 32 MHz : 10 ns MAX
9 MHz TO 32 MHz : 10 ns MAX
32 MHz TO 80 MHz : 6 ns MAX
32 MHz TO 80 MHz : 6 ns MAX
80 MHz TO 125 MHz : 4 ns MAX
80 MHz TO 125 MHz : 4 ns MAX
LOGIC "0" LEVEL
+0.5 V MAX, SINK TO 16 mA
+0.5 V MAX, SINK TO 16 mA
LOGIC "1" LEVEL
+2.4 V MIN, SOURCE 0.4 mA
+2.4 V MIN, SOURCE 0.4 mA
LOAD
1 TO 10 TTL STANDARD
1 TO 10 TTL STANDARD
SPECIFICATIONS
PART NUMBERING SYSTEM
EXAMPLE: CO1100-20.000-EXT-T, CO13050-32.000-T-TR
VCC
"1" LEVEL
"0" LEVEL
0 VDC
t
T
+2.5 VDC
+1.5 VDC
+0.5 VDC
tf
tr
OUTPUT WAVEFORM
ENVIRONMENTAL
TEMPERATURE CYCLE
MIL-STD 883, METHOD 1010, 10 CYCLES -20 C TO 85 C
SHOCK
MIL-STD-202, METHOD 213, TEST CONDITION C
VIBRATION
MIL-STD-202, METHOD 204, TEST CONDITION A
RESISTANCE TO
SOLDERING HEAT
MIL-STD-202, METHOD 210, TEST CONDITION B
HUMIDITY
85% RELATIVE HUMIDITY AT 85 C 250 HOURS
MECHANICAL
GROSS LEAK TEST
MIL-STD-883, METHOD 1014, TEST CONDITION C
FINE LEAK TEST
MIL-STD-883, METHOD 1014, TEST CONDITION A
TERMINAL STRENGTH
MIL-STD-202, METHOD 211, TEST CONDITION A AND C
MARKING INK
EPOXY, HEAT CURED.
MOISTURE RESISTANCE
MIL-STD 202, METHOD 106, OMIT STEP 7B
SOLDERABILITY
MIL-STD-202, METHOD 208, 95% COVERAGE
SOLVENT RESISTANCE
MIL-STD-202, METHOD 2002, METHOD 215
FREQUENCY STABILITY INCLUSIVE OF ROOM TOLERANCE ,
FREQUENCY STABILITY OVER TEMPERATURE, 10% POWER SUPPLY VARIATION, AGING, SHOCK, AND VIBRATION
+3.3 VOLT VERSION IS AVAILABLE. CONSULT RALTRON FOR SPECIFICATIONS
OUTPUT LOADS ALSO AVAILABLE AT 15 pF, 30 pF AND 50 pF. CONSULT RALTRON FOR SPECIFICATIONS
ENVIRONMENTAL AND TECHNICAL CONDITIONS
FEATURES
STANDARD 8 AND 14 PIN DIP PACKAGE
TOLERANCE AND STABILITY TO
25 PPM
LOW COST
AVAILABLE IN 3.3 VOLT
FREQUENCY
EXTENDED
TEMPERA TURE
TR
GW
3.3
TA PE A ND REEL*
GULL WING
+3.3 V
OPTIONS
-
EXT
-
T
SY MMETRY
TIGHT SY MMETRY
S ERIES
CO1
CO13
(14 PIN DIP)
(8 PIN DIP)
-
100 PPM
50 PPM
25 PPM
100
050
025
FREQUENCY
STA B ILITY
-
IN MHz
* Available for Gull Wing only
PDF 
ZIP