RF Monolithics, Inc.
Phone: (972) 233-2903
Fax: (972) 387-8148
E-mail: info@rfm.com
Page 1 of 3
RFM Europe
Phone: 44 1963 251383
Fax: 44 1963 251510
http://www.rfm.com
1999 by RF Monolithics, Inc. The stylized RFM logo are registered trademarks of RF Monolithics, Inc.
RF1411D-030105
Electrical Characteristics
Characteristic
Sym
Notes
Minimum
Typical
Maximum
Units
Center Frequency @ 25C
f
C
1, 2, 3
869.2625
MHz
I.L.
1, 3
3.3
4.5
dB
PassBand (relative to IL
min
)
868.9125 -869.6125
0.4
1.0
dB
Pass Bandwidth (relative to IL
min
)
BW
3
1, 3
1250
kHz
Rejection (relative to IL
min
)
10-700 MHz
1, 3
50
55
dB
700-842 MHz
35
40
842-864 MHz
25
28
864-866 MHz
15
24
872-879 MHz
8
13
879-909 MHz
15
20
909-1000 MHz
40
45
Temperature Coeff
0.032
ppm/C
2
Operating Temperature Range
-45
+85
C
Impedance @ fc
Input Z
IN
= R
IN
ll C
IN
Z
IN
1
117
ll 3.7pf
Output Z
OUT
= R
OUT
ll C
OUT
Z
OUT
1
117
ll 3.7pf
Lid Symbolization (in addition to Lot and/or Date Codes)
512 // YWWS
Standard Reel Quantity
7 Inch Reel
8
500 Pieces/Reel
13 Inch Reel
3000 Pieces/Reel
Ideal Front-End Filter for European Wireless Receivers
Low-Loss, Coupled-Resonator Quartz Design
Simple External Impedance Matching
Complies with Directive 2002/95/EC (RoHS)
The RF1411D is a low-loss, compact, and economical surface-acoustic-wave (SAW) filter designed to pro-
vide front-end selectivity in 869.2625 MHz receivers. Receiver designs using this filter include superhet IF,
direct conversion and superregen. Typical applications of these receivers are wireless remote-control and
security devices operating in Europe under ETSI I-ETS 300 220, in Germany under FTZ 17 TR 2100, in the
United Kingdom under DTI MPT 1340 (for automotive only), in France under PTT Specifications ST/PAA/
TPA/AGH/1542, and in Scandinavia.
This coupled-resonator filter (CRF) uses selective null placement to provide suppression, typically greater
than 40 dB, of the LO and image spurious responses of superhet receivers with 10.7 MHz IF. RFM's ad-
vanced SAW design and fabrication technology is utilized to achieve high performance and very low loss with
simple external impedance matching (not included).
869.2625 MHz
SAW Filter
RF1411D
CAUTION: Electrostatic Sensitive Device. Observe precautions for handling.
Notes:
1.
Unless noted otherwise, all measurements are made with the filter installed in the specified test fixture which is connected to a 50
test system with VSWR
1.2:1.
The test fixture L and C are adjusted for minimum insertion loss at the filter center frequency, f
c
. Note that insertion loss and bandwidth are dependent on the imped-
ance matching component values and quality.
2.
The frequency f
c
is defined as the midpoint between the 3dB frequencies.
3.
Where noted, specifications apply over the entire specified operating temperature range of -45C to +85C.
4.
Frequency aging is the change in fc with time and is specified at +65C or less. Aging may exceed the specification for prolonged temperatures above +65C. Typ-
ically, aging is greatest the first year after manufacture, decreasing significantly in subsequent years.
5.
The design, manufacturing process, and specifications of this device are subject to change.
6.
One or more of the following U.S. Patents apply: 4,54,488, 4,616,197, and others pending.
7.
All equipment designs utilizing this product must be approved by the appropriate government agency prior to manufacture or sale.
8.
Tape and reel standard per ANSI / EIA 481.
SM3838-8 Case
3.8 x 3.8
Pb
PDF 
ZIP
