SF1134A 170.6 MHz SAW Filter
RF Monolithics, Inc.
Phone: +1(972)233-2903
European Sales Office
4347 Sigma Road
Fax: +1(972)387-8148
44 1963 251383
Dallas, Texas 75244
e-mail:
info@rfm.com
44 1963 251510
USA
Home page:
www.rfm.com
SF1134A.DOC 1/17/2001 D
Electrical Connections
Connection
Terminals
Port 1 Hot
10
Port 1 Gnd Return
1
Port 2 Hot
5
Port 2 Gnd Return
6
Case Ground
All others
Absolute Maximum Ratings
Rating
Value
Units
Maximum Incident Power in Passband
+20
dBm
Max. DC voltage between any 2 terminals
30
VDC
Storage Temperature Range
-40 to +85
C
Max Soldering Profile
265
C for 10 s
Designed for EDGE BTS Receiver IF Applications
Low Insertion Loss
Excellent Size-Performance Ratio
Hermetic SMP-75 Surface-Mount Case
Unbalanced Input and Output
Associated Plots Attached
Characteristic
Sym
Min
Typ
Max
Units
Notes
Nominal Center Frequency
fc
170.600
MHz
IL
9.0
dB
1
90
150
kHz
.5
1
dB
P-P
Passband
Insertion Loss at fc
0.5 dB Passband
1 dB Passband
Amplitude Ripple over fc
90 kHz
Amplitude Ripple over fc
150 kHz
Group Delay Variation over fc
90 kHz GDV
TBD
400
ns
P-P
1, 2
13
15
27
35
40
45
43
55
47
55
50
55
45
55
Rejection
fc-0.6 to fc-0.4 and fc+0.4 to fc+0.6 MHz
fc-0.8 to fc-0.6 and fc+0.6 to fc+0.8 MHz
fc-1.6 to fc-0.8 and fc+0.8 to fc+1.6 MHz
fc-3.0 to fc-1.6 and fc+1.6 to fc+3.0 MHz
fc-5.8 to fc-3.0 and fc+3.0 to fc+5.8 MHz
fc-35 to fc-5.8 and fc+5.8 to fc+35 MHz
fc-75 to fc-35 and fc+35 to fc+75 MHz
DC to fc-75 and fc+75 to fc+1000 MHz
40
dB
1, 2, 3
Operating Temperature Range
-10
+85
C
1
Impedance Matching to 50
unbalanced
External L-C
Case Style
SMP-75 19 x 6.5 mm Nominal Footprint
Lid symbolization (YY = year, WW = week)
RFM SF1088A YYWW
PRELIMINARY
Notes:
1. Unless noted otherwise, all specifications apply
over the operating temperature range with filter soldered to the specified
demonstration board with impedance matching to 50
and measured with 50
network analyzer.
2. Unless noted otherwise, all frequency specifications are referenced to the nominal center frequency, fc.
3. Rejection is measured as attenuation below the minimum IL point in the passband. Rejection in final user application is
dependent on PCB layout and external impedance matching design. See Application Note No. 42 for details.
4. "LRIP" or "L" after the part number indicates "low rate initial production" and "ENG" or "E" indicates "engineering prototypes."
5. The design, manufacturing process, and specifications of this filter are subject to change.
6. Either Port 1 or Port 2 may be used for either input or output in the design. However, impedances and impedance matching
may vary between Port 1 and Port 2, so that the filter must always be installed in one direction per the circuit design.
7. US and international patents may apply.
8. RFM, stylized RFM logo, and RF Monolithics, Inc. are registered trademarks of RF Monolithics, Inc.
9.
Copyright 1999, RF Monolithics Inc.
10. Electrostatic Sensitive Device. Observe precautions for handling.
PDF 
ZIP