LOW NOISE 150mA LDO REGULATOR
R1113Z SERIES
1
R1113Z_E.doc/2003/02/19
NO. EA-101-0301
OUTLINE
The R1113Z Series are CMOS-based voltage regulator ICs with high output voltage accuracy, extremely low supply
current, low ON-resistance, and high ripple rejection. Each of these ICs consists of a voltage reference unit, an error
amplifier, resistors, a current limit circuit, and a chip enable circuit.
These ICs perform with low dropout voltage and a chip enable function. The line transient response and load tran-
sient response of the R1113Z Series are excellent, thus these ICs are very suitable for the power supply for hand-held
communication equipment.
The output voltage of these ICs is fixed with high accuracy. Since the package for these ICs is WL-CSP (Wafer
Level CSP), high density mounting of the ICs on boards is possible.
FEATURES
Ultra-Low Supply Current ..................................................Typ. 100A
Standby Mode......................................................................Typ. 0.1A
Low Dropout Voltage ..........................................................Typ. 0.23V (I
OUT
=100mA 3.0V Output type)
High Ripple Rejection .........................................................Typ. 80dB(f=1kHz 3.0V Output type)
Low Temperature-Drift Coefficient of Output Voltage......Typ. 100ppm/C
Excellent Line Regulation...................................................Typ. 0.05%/V
High Output Voltage Accuracy ...........................................2.0%
Excellent Dynamic Response
Small Package .....................................................................WL-CSP(Wafer Level CSP)
Output Voltage.....................................................................Stepwise setting with a step of 0.1V in the range of 1.5V to
5.0V is possible
Built-in Chip Enable Circuit (2 types; A: active low, B: active high)
Built-in Fold Back Protection Circuit .................................Typ. 30mA (Current at short mode)
Ceramic capacitors are recommended to be used with this IC
APPLICATIONS
Power source for cellular phones such as GSM, CDMA and various kinds of PCS.
Power source for electrical appliances such as cameras, VCRs and camcorders.
Power source for battery-powered equipment.
R1113Z
2
BLOCK DIAGRAM
R1113Zxx1A
R1113Zxx1B
V
OUT
GND
V
DD
CE
Vref
Current Limit
+
-
3
4
2
1
V
OUT
GND
V
DD
CE
Vref
Current Limit
+
-
3
4
2
1
SELECTION GUIDE
The output voltage, the active type, the packing type, and the taping type for the ICs can be selected at the user's
request. The selection can be made with designating the part number as shown below;
R1113xxx1x-xx
Part Number
a b c d
Code
Contents
a
Designation of Package Type :
Z:WL-CSP (Wafer Level CSP)
b
Setting Output Voltage (V
OUT
) :
Stepwise setting with a step of 0.1V in the range of 1.5V to 5.0V is possible.
c
Designation of Active Type :
A : active low type
B : active high type
d
Designation of Taping Type :
Ex. TR, TL (refer to Taping Specifications; TR type is the standard direction.)
R1113Z
3
PIN CONFIGURATION
WL-CSP 4Pin
3 V
DD
4 CE
2 V
OUT
Bottom View
1 GND
Top View
4
3
1
2
PIN DESCRIPTION
Pin No.
Symbol
Description
1
GND
Ground Pin
2
V
OUT
Output pin
3
V
DD
Input Pin
4
CE or CE
Chip Enable Pin
ABSOLUTE MAXIMUM RATINGS
Symbol
Item
Rating
Unit
V
IN
Input Voltage
7.0
V
V
CE
Input Voltage(CE or CE Pin)
-0.3 ~ V
IN
+0.3
V
V
OUT
Output Voltage
-0.3 ~ V
IN
+0.3
V
I
OUT
Output Current
200
mA
P
D
Power Dissipation
190
mW
Topt
Operating Temperature Range
-40 ~ 85
C
Tstg
Storage Temperature Range
-55 ~ 125
C
R1113Z
4
ELECTRICAL CHARACTERISTICS
R1113Zxx1A
Topt=25C
Symbol
Item
Conditions
Min.
Typ.
Max.
Unit
V
OUT
Output Voltage
V
IN
= Set V
OUT
+1V
1mA I
OUT
30mA
V
OUT
0.98
V
OUT
1.02
V
I
OUT
Output Current
V
IN
- V
OUT
= 1.0V
150
mA
V
OUT
/I
OUT
Load Regulation
V
IN
= Set V
OUT
+1V
1mA I
OUT
80mA
20
45
mV
V
DIF
Dropout Voltage
Refer to the ELECTRICAL CHARACTERISTICS by OUTPUT VOLTAGE
I
SS
Supply Current
V
IN
= Set V
OUT
+1V
100
170
A
Istandby
Supply Current (Standby) V
IN
= V
CE
= Set V
OUT
+1V
0.1
1.0
A
V
OUT
/V
IN
Line Regulation
Set V
OUT
+0.5V V
IN
6V
I
OUT
= 30mA
0.05
0.20
%/V
RR
Ripple Rejection
Refer to the ELECTRICAL CHARACTERISTICS by OUTPUT VOLTAGE
V
IN
Input Voltage
2.0
6.0
V
V
OUT
/T
Output Voltage
Temperature Coefficient
I
OUT
= 30mA
-40C Topt 85C
100
ppm
/C
Ilim
Short Current Limit
V
OUT
= 0V
30
mA
R
PU
CE Pull-up Resistance
2.5
5.0
10.0
M
V
CEH
CE Input Voltage "H"
1.5
V
IN
V
V
CEL
CE Input Voltage "L"
0.00
0.25
V
e
n
Output Noise
BW=10Hz to 100kHz
30
Vrms
R1113Zxx1B
Topt=25C
Symbol
Item
Conditions
Min.
Typ.
Max.
Unit
V
OUT
Output Voltage
V
IN
= Set V
OUT
+1V
1mA I
OUT
30mA
V
OUT
0.98
V
OUT
1.02
V
I
OUT
Output Current
V
IN
- V
OUT
= 1.0V
150
mA
V
OUT
/I
OUT
Load Regulation
V
IN
= Set V
OUT
+1V
1mA I
OUT
80mA
20
45
mV
V
DIF
Dropout Voltage
Refer to the ELECTRICAL CHARACTERISTICS by OUTPUT VOLTAGE
I
SS
Supply Current
V
IN
= Set V
OUT
+1V
100
170
A
Istandby
Supply Current (Standby)
V
IN
= Set V
OUT
+1V
V
CE
=GND
0.1
1.0
A
V
OUT
/V
IN
Line Regulation
Set V
OUT
+0.5V V
IN
6V
I
OUT
= 30mA
0.05
0.20
%/V
RR
Ripple Rejection
Refer to the ELECTRICAL CHARACTERISTICS by OUTPUT VOLTAGE
V
IN
Input Voltage
2.0
6.0
V
V
OUT
/T
Output Voltage
Temperature Coefficient
I
OUT
= 30mA
-40C Topt 85C
100
ppm
/C
Ilim
Short Current Limit
V
OUT
= 0V
30
mA
R
PD
CE Pull-down Resistance
2.5
5.0
10.0
M
V
CEH
CE Input Voltage "H"
1.5
V
IN
V
V
CEL
CE Input Voltage "L"
0.00
0.25
V
e
n
Output Noise
BW=10Hz to 100kHz
30
Vrms
R1113Z
5
ELECTRICAL CHARACTERISTICS by OUTPUT VOLTAGE
Topt = 25C
Dropout Voltage
V
DIF
(V)
Output Voltage V
OUT
(V)
Condition
Typ.
Max.
1.5
0.50
0.70
1.6
0.45
0.65
1.7
0.40
0.60
1.8
0.34
0.55
1.9
0.28
0.44
2.0 V
OUT
2.3
0.25
0.35
2.4 V
OUT
2.7
0.24
0.29
2.8 V
OUT
5.0
I
OUT
= 100mA
0.23
0.26
Topt = 25C
Ripple Rejection
RR (dB)
Output Voltage V
OUT
(V)
Condition
Typ.
Max.
1.5 V
OUT
4.0
80
4.1 V
OUT
5.0
f = 1kHz, Ripple 0.5Vp-p
V
IN
= Set V
OUT
+ 1V
70
OPERATION
R1113Zxx1A
R1113Zxx1B
V
OUT
GND
V
DD
CE
Vref
R1
R2
Current Limit
+
-
3
4
2
1
V
OUT
GND
V
DD
CE
Vref
Current Limit
+
-
3
4
2
1
R1
R2
In these ICs, fluctuation of output voltage, V
OUT
is detected by feedback registers R1, R2, and the result is com-
pared with a reference voltage by the error amplifier, so that a constant voltage is output. A current limit circuit for
protection in short mode and a chip enable circuit, are included.
PDF 
ZIP