ChipFind - документация

Электронный компонент: K4D623237A

Скачать:  PDF   ZIP
64M DDR SDRAM
- 1 -
K4D623237A
Rev. 1.2 (Feb. 2001)
64Mbit DDR SDRAM
Revision 1.2
February 2001
512K x 32Bit x 4 Banks
with Bi-directional Data Strobe and without DLL
Double Data Rate Synchronous DRAM
Samsung Electronics reserves the right to change products or specification without notice.
64M DDR SDRAM
- 2 -
K4D623237A
Rev. 1.2 (Feb. 2001)
Revision History
Revision 1.2 (February 1, 2001)
Corrected timing diaram on page 28,32.
Removed K4D623237A-QC50
Revision 1.1 (July 12, 2000)
Removed Block Write function. Accordingly pin number 52 must be connected to low ( MCL only )
Removed Write Interrupted by Read function.
Changed I
CC1
/I
CC2N
/I
CC3N
/I
CC5
of K4D623237A-* in "DC Characteristics" table.
Changed DC operating conditions
- V
REF
from 1.15V(min)/1.35V(max) to 0.49*V
DDQ
/0.51*V
DDQ
- V
IH
/V
IL
from V
REF
+0.18(min)/V
REF
-0.18(max) to V
REF
+0.15(min)
/
V
REF
-0.15(max)
Revision 1.0 (May 16, 2000)
Changed tCDLR from 1CLK to 2CLK
Changed tRPST from 0.9/1.1tCK to 0.4/0.5tCK
Changed tAC(max) and tACS(max) of K4D623237A-QC70 from 5.5ns to 6.0ns
Revision 0.1 (April 24, 2000) - Preliminary
Changed tCDLR from 2CLK to 1CLK
Revision 0.0 (Februray 2, 2000) - Target
Defined Target Specification
64M DDR SDRAM
- 3 -
K4D623237A
Rev. 1.2 (Feb. 2001)
The K4D623237 is 67,108,864 bits of hyper synchronous data rate Dynamic RAM organized as 4 x 524,288 words by 32
bits, fabricated with SAMSUNG
s high performance CMOS technology. Synchronous features with Data Strobe allow
extremely high performance up to 1.5GB/s/chip. I/O transactions are possible on both edges of the clock cycle. Range of
operating frequencies, programmable burst length and programmable latencies allow the device to be useful for a variety
of high performance memory system applications.
3.3V
5% power supply for device operation
2.5V
5% power supply for I/O interface
SSTL_2 compatible inputs/outputs
4 banks operation
MRS cycle with address key programs
-. Read latency 3 (clock)
-. Burst length (2, 4, 8 and Full page)
-. Burst type (sequential & interleave)
Full page burst length for sequential burst type only
Start address of the full page burst should be even
All inputs except data & DM are sampled at the positive
going edge of the system clock
Differential clock input
Data I/O transactions on both edges of Data strobe
Data input & output & DM are synchronized with DQS
GENERAL DESCRIPTION
FEATURES
Edge aligned data & data strobe output
Center aligned data & data strobe input
DM for write masking only
Auto & Self refresh
16ms refresh period (2K cycle)
100pin TQFP package
Maximum clock frequency up to 183MHz
Maximum data rate up to 366Mbps/pin
FOR 512K x 32Bit x 4 Bank DDR SDRAM
512K x 32Bit x 4 Banks Double Data Rate Synchronous DRAM
with Bi-directional Data Strobe and without DLL
ORDERING INFORMATION
Part NO.
Max Freq.
Max Data Rate
Interface
Package
K4D623237A-QC55
183MHz
366Mbps/pin
SSTL_2
100 TQFP
K4D623237A-QC60
166MHz
333Mbps/pin
K4D623237A-QC70
143MHz
286Mbps/pin
64M DDR SDRAM
- 4 -
K4D623237A
Rev. 1.2 (Feb. 2001)
PIN CONFIGURATION
(Top View)
PIN DESCRIPTION
CK,CK
Differential Clock Input
BA
0
, BA
1
Bank Select Address
CKE
Clock Enable
A
0
~A
10
Address Input
CS
Chip Select
DQ
0
~ DQ
31
Data Input/Output
RAS
Row Address Strobe
V
DD
Power
CAS
Column Address Strobe
V
SS
Ground
WE
Write Enable
V
DDQ
Power for DQ
s
DQS
Data Strobe
V
SSQ
Ground for DQ
s
DM0 ~ DM3
Data Mask
MCL
Must Connect Low
RFU
Reserved for Future Use
-
-
DQ29
VSSQ
DQ30
DQ31
VSS
VDDQ
N.C
N.C
N.C
N.C
N.C
VSSQ
RFU
DQS
VDDQ
VDD
DQ0
DQ1
VSSQ
DQ2
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
D
Q
3
V
D
D
Q
D
Q
4
D
Q
5
V
S
S
Q
D
Q
6
D
Q
7
V
D
D
Q
D
Q
1
6
D
Q
1
7
V
S
S
Q
D
Q
1
8
D
Q
1
9
V
D
D
Q
V
D
D
V
S
S
D
Q
2
0
D
Q
2
1
V
S
S
Q
D
Q
2
2
D
Q
2
3
V
D
D
Q
D
M
0
D
M
2
W
E
C
A
S
R
A
S
C
S
B
A
0

B
A
1
1
2
3
4
5
6
7
8
9
1
0
1
1
1
2
1
3
1
4
1
5
1
6
1
7
1
8
1
9
2
0
2
1
2
2
2
3
2
4
2
5
2
6
2
7
2
8
2
9
3
0
A7
A6
A5
A4
VSS
A9
N.C
N.C
N.C
N.C
N.C
N.C
N.C
N.C
A10
VDD
A3
A2
A1
A0
50
49
48
47
46
45
44
43
42
41
40
39
38
37
36
35
34
33
32
31
100 Pin TQFP
20 x 14 mm
2
0.65mm pin Pitch
D
Q
2
8
V
D
D
Q
D
Q
2
7
D
Q
2
6
V
S
S
Q
D
Q
2
5
D
Q
2
4
V
D
D
Q
D
Q
1
5
D
Q
1
4
V
S
S
Q
D
Q
1
3
D
Q
1
2
V
D
D
Q
V
S
S
V
D
D
D
Q
1
1
D
Q
1
0
V
S
S
Q
D
Q
9
D
Q
8
V
D
D
Q
V
R
E
F
D
M
3
D
M
1
C
K
C
K
C
K
E
M
C
L
A
8
(
A
P
)
8
0
7
9
7
8
7
7
7
6
7
5
7
4
7
3
7
2
7
1
7
0
6
9
6
8
6
7
6
6
6
5
6
4
6
3
6
2
6
1
6
0
5
9
5
8
5
7
5
6
5
5
5
4
5
3
5
2
5
1
64M DDR SDRAM
- 5 -
K4D623237A
Rev. 1.2 (Feb. 2001)
INPUT/OUTPUT FUNCTIONAL DESCRIPTION
*1 : The timing reference point for the differential clocking is the cross point of CK and CK.
For any applications using the single ended clocking, apply V
REF
to CK pin.
Symbol
Type
Function
CK, CK
*1
Input
The differential system clock Input.
All of the inputs are sampled on the rising edge of the clock except
DQ
s and DM
s that are sampled on both edges of the DQS.
CKE
Input
Activates the CK signal when high and deactivates the CK signal
when low. By deactivating the clock, CKE low indicates the Power
down mode or Self refresh mode.
CS
Input
CS enables the command decoder when low and disabled the com-
mand decoder when high. When the command decoder is disabled,
new commands are ignored but previous operations continue.
RAS
Input
Latches row addresses on the positive going edge of the CK with
RAS low. Enables row access & precharge.
CAS
Input
Latches column addresses on the positive going edge of the CK with
CAS low. Enables column access.
WE
Input
Enables write operation and row precharge.
Latches data in starting from CAS, WE active.
DQS
Input/Output
Data input and output are synchronized with both edge of DQS.
DM
0
~ DM
3
Input
Data In mask. Data In is masked by DM Latency=0 when DM is high
in burst write. DM
0
for DQ
0
~ DQ
7,
DM
1
for DQ
8
~ DQ
15,
DM
2
for
DQ
16
~ DQ
23,
DM
3
for DQ
24
~ DQ
31.
DQ
0
~ DQ
31
Input/Output
Data inputs/Outputs are multiplexed on the same pins.
BA
0
, BA
1
Input
Selects which bank is to be active.
A
0
~ A
10
Input
Row/Column addresses are multiplexed on the same pins.
Row addresses : RA
0
~ RA
10
, Column addresses : CA
0
~ CA
7
.
Column address CA
8
is used for auto precharge.
V
DD
/V
SS
Power Supply
Power and ground for the input buffers and core logic.
V
DDQ
/V
SSQ
Power Supply
Isolated power supply and ground for the output buffers to provide
improved noise immunity.
V
REF
Power Supply
Reference voltage for inputs, used for SSTL interface.
MCL
MCL
Must be connected low