K4S560832D
CMOS SDRAM
Rev. 1.1 May. 2003
256Mbit SDRAM
8M x 8bit x 4 Banks
Synchronous DRAM
LVTTL
Revision 1.1
May. 2003
* Samsung Electronics reserves the right to change products or specification without notice.
K4S560832D
CMOS SDRAM
Rev. 1.1 May. 2003
Revision History
Revision 0.0 (Jan. , 2002)
- First release
Revision 0.1(May., 2003)
- ICC6 of Low power is changed from 1.0 to 1.5 due to typo.
K4S560832D
CMOS SDRAM
Rev. 1.1 May. 2003
The K4S560832D is 268,435,456 bits synchronous high data rate
Dynamic RAM organized as 4 x 8,392,608 words by 8bits, fabri-
cated with SAMSUNG's high performance CMOS technology. Syn-
chronous design allows precise cycle control with the use of
system clock I/O transactions are possible on every clock cycle.
Range of operating frequencies, programmable burst length and
programmable latencies allow the same device to be useful for a
variety of high bandwidth, high performance memory system appli-
cations.
JEDEC standard 3.3V power supply
LVTTL compatible with multiplexed address
Four banks operation
MRS cycle with address key programs
-. CAS latency (2 & 3)
-. Burst length (1, 2, 4, 8 & Full page)
-. Burst type (Sequential & Interleave)
All inputs are sampled at the positive going edge of the system
clock.
Burst read single-bit write operation
DQM for masking
Auto & self refresh
64ms refresh period (8K Cycle)
GENERAL DESCRIPTION
FEATURES
FUNCTIONAL BLOCK DIAGRAM
8M x 8Bit x 4 Banks Synchronous DRAM
ORDERING INFORMATION
Part No.
Max Freq.
Interface Package
K4S560832D-TC/L7C
133MHz(CL=2)
LVTTL
54pin
TSOP(II)
K4S560832D-TC/L75
133MHz(CL=3)
K4S560832D-TC/L1H
100MHz(CL=2)
K4S560832D-TC/L1L
100MHz(CL=3)
Bank Select
Data Input Register
8M x 8
8M x 8
Sense AMP
Output
Buf
f
er
I
/O Contr
o
l
Column Decoder
Latency & Burst Length
Programming Register
Address Regis
t
er
Row
Buf
f
er
Refresh Cou
n
ter
Row Decoder
C
ol. Buf
f
er
LRAS
LCBR
LCKE
LRAS
LCBR
LWE
LDQM
CLK
CKE
CS
RAS
CAS
WE
L(U)DQM
LWE
LDQM
DQi
CLK
ADD
LCAS
LWCBR
8M x 8
8M x 8
Timing Register
* Samsung Electronics reserves the right to change products or specification without notice.
K4S560832D
CMOS SDRAM
Rev. 1.1 May. 2003
V
DD
DQ0
V
DDQ
N.C
DQ1
V
SSQ
N.C
DQ2
V
DDQ
N.C
DQ3
V
SSQ
N.C
V
DD
N.C
WE
CAS
RAS
CS
BA0
BA1
A10/AP
A0
A1
A2
A3
V
DD
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
54
53
52
51
50
49
48
47
46
45
44
43
42
41
40
39
38
37
36
35
34
33
32
31
30
29
28
PIN CONFIGURATION (Top view)
V
SS
DQ7
V
SSQ
N.C
DQ6
V
DDQ
N.C
DQ5
V
SSQ
N.C
DQ4
V
DDQ
N.C
V
SS
N.C/RFU
DQM
CLK
CKE
A12
A11
A9
A8
A7
A6
A5
A4
V
SS
54Pin TSOP (II)
(400mil x 875mil)
(0.8 mm Pin pitcH)
PIN FUNCTION DESCRIPTION
Pin
Name
Input Function
CLK
System clock
Active on the positive going edge to sample all inputs.
CS
Chip select
Disables or enables device operation by masking or enabling all inputs except
CLK, CKE and DQM
CKE
Clock enable
Masks system clock to freeze operation from the next clock cycle.
CKE should be enabled at least one cycle prior to new command.
Disable input buffers for power down in standby.
A
0
~ A
12
Address
Row/column addresses are multiplexed on the same pins.
Row address : RA
0
~ RA
12
, Column address : CA
0
~ CA
9
BA
0
~ BA
1
Bank select address
Selects bank to be activated during row address latch time.
Selects bank for read/write during column address latch time.
RAS
Row address strobe
Latches row addresses on the positive going edge of the CLK with RAS low.
Enables row access & precharge.
CAS
Column address strobe
Latches column addresses on the positive going edge of the CLK with CAS low.
Enables column access.
WE
Write enable
Enables write operation and row precharge.
Latches data in starting from CAS, WE active.
DQM
Data input/output mask
Makes data output Hi-Z, t
SHZ
after the clock and masks the output.
Blocks data input when DQM active.
DQ
0
~
7
Data input/output
Data inputs/outputs are multiplexed on the same pins.
V
DD
/V
SS
Power supply/ground
Power and ground for the input buffers and the core logic.
V
DDQ
/V
SSQ
Data output power/ground
Isolated power supply and ground for the output buffers to provide improved noise
immunity.
N.C/RFU
No connection
/reserved for future use
This pin is recommended to be left No Connection on the device.
K4S560832D
CMOS SDRAM
Rev. 1.1 May. 2003
ABSOLUTE MAXIMUM RATINGS
Parameter
Symbol
Value
Unit
Voltage on any pin relative to Vss
V
IN
, V
OUT
-1.0 ~ 4.6
V
Voltage on V
DD
supply relative to Vss
V
DD
, V
DDQ
-1.0 ~ 4.6
V
Storage temperature
T
STG
-55 ~ +150
C
Power dissipation
P
D
1
W
Short circuit current
I
OS
50
mA
Permanent device damage may occur if "ABSOLUTE MAXIMUM RATINGS" are exceeded.
Functional operation should be restricted to recommended operating condition.
Exposure to higher than recommended voltage for extended periods of time could affect device reliability.
Note :
DC OPERATING CONDITIONS
Recommended operating conditions (Voltage referenced to V
SS
= 0V, T
A
= 0 to 70
C)
Parameter
Symbol
Min
Typ
Max
Unit
Note
Supply voltage
V
DD
, V
DDQ
3.0
3.3
3.6
V
Input logic high voltage
V
IH
2.0
3.0
V
DD
+0.3
V
1
Input logic low voltage
V
IL
-0.3
0
0.8
V
2
Output logic high voltage
V
OH
2.4
-
-
V
I
OH
= -2mA
Output logic low voltage
V
OL
-
-
0.4
V
I
OL
= 2mA
Input leakage current
I
LI
-10
-
10
uA
3
1. V
IH
(max) = 5.6V AC. The overshoot voltage duration is
3ns.
2. V
IL
(min) = -2.0V AC. The undershoot voltage duration is
3ns.
3. Any input 0V
V
IN
V
DDQ
.
Input leakage currents include Hi-Z output leakage for all bi-directional buffers with Tri-State outputs.
Notes :
1. -75/7C only specify a maximum value of 3.5pF
2. -75/7C only specify a maximum value of 3.8pF
3. -75/7C only specify a maximum value of 6.0pF
Notes :
CAPACITANCE
(V
DD
= 3.3V, T
A
= 23
C, f = 1MHz, V
REF
=1.4V
200
mV)
Pin
Symbol
Min
Max
Unit
Note
Clock
C
CLK
2.5
4.0
pF
1
RAS, CAS, WE, CS, CKE, DQM
C
IN
2.5
5.0
pF
2
Address
C
ADD
2.5
5.0
pF
2
DQ
0
~ DQ
15
C
OUT
4.0
6.5
pF
3
PDF 
ZIP