M366S1654CTS
PC133/PC100 Unbuffered DIMM
Rev. 0.1 Sept. 2001
The Samsung M366S1654CTS is a 8M bit x 64 Synchronous
Dynamic RAM high density memory module. The Samsung
M366S1654CTS consists of four CMOS 8M x 16 bit with 4banks
Synchronous DRAMs in TSOP-II 400mil package and a 2K
EEPROM in 8-pin TSSOP package on a 168-pin glass-epoxy
substrate.Three 0.1uF decoupling capacitors are mounted on
the printed circuit board in parallel for each SDRAM.
The M366S1654CTS is a Dual In-line Memory Module and is
intended for mounting into 168-pin edge connector sockets.
Synchronous design allows precise cycle control with the use of
system clock. I/O transactions are possible on every clock cycle.
Range of operating frequencies, programmable latencies allows
the same device to be useful for a variety of high bandwidth,
high performance memory system applications.
Performance range
Burst mode operation
Auto & self refresh capability (8192 Cycles/64ms)
LVTTL compatible inputs and outputs
Single 3.3V
0.3V power supply
MRS cycle with address key programs
Latency (Access from column address)
Burst length (1, 2, 4, 8 & Full page)
Data scramble (Sequential & Interleave)
All inputs are sampled at the positive going edge of the
system clock
Serial presence detect with EEPROM
PCB : Height (1,000mil) , single sided component
Part No.
Max Freq. (Speed)
M366S1654CTS-L7C/C7C
133MHz (7.5ns@CL=2)
M366S1654CTS-L7A/C7A
133MHz (7.5ns@CL=3)
M366S1654CTS-L1H/C1H
100MHz (6.0ns@CL=2)
M366S1654CTS-L1L/C1L
100MHz (6.0ns@CL=3)
FEATURE
GENERAL DESCRIPTION
M366S1654CTS SDRAM DIMM
16Mx64 SDRAM DIMM based on 16Mx16, 4Banks, 8K Refresh, 3.3V Synchronous DRAMs with SPD
PIN NAMES
* These pins are not used in this module.
**
These pins should be NC in the system
which does not support SPD.
Pin Name
Function
A0 ~ A11
Address input (Multiplexed)
BA0 ~ BA1
Select bank
DQ0 ~ DQ63
Data input/output
CLK0, CLK2
Clock input
CKE0
Clock enable input
CS0, CS2
Chip select input
RAS
Row address strobe
CAS
Column address strobe
WE
Write enable
DQM0 ~ 7
DQM
V
DD
Power supply (3.3V)
V
SS
Ground
*V
REF
Power supply for reference
SDA
Serial data I/O
SCL
Serial clock
SA0 ~ 2
Address in EEPROM
*WP
Write protection
DU
Don
t use
NC
No connection
PIN CONFIGURATIONS (Front side/back side)
Pin
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
Front
V
SS
DQ0
DQ1
DQ2
DQ3
V
DD
DQ4
DQ5
DQ6
DQ7
DQ8
V
SS
DQ9
DQ10
DQ11
DQ12
DQ13
V
DD
DQ14
DQ15
*CB0
*CB1
V
SS
NC
NC
V
DD
WE
DQM0
Pin
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
Front
DQM1
CS0
DU
V
SS
A0
A2
A4
A6
A8
A10/AP
BA1
V
DD
V
DD
CLK0
V
SS
NC
CS2
DQM2
DQM3
NC
V
DD
NC
NC
*CB2
*CB3
V
SS
DQ16
DQ17
Pin
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
Front
DQ18
DQ19
V
DD
DQ20
NC
*V
REF
*CKE1
V
SS
DQ21
DQ22
DQ23
V
SS
DQ24
DQ25
DQ26
DQ27
V
DD
DQ28
DQ29
DQ30
DQ31
V
SS
CLK2
NC
*WP
**SDA
**SCL
V
DD
Pin
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
Back
V
SS
DQ32
DQ33
DQ34
DQ35
V
DD
DQ36
DQ37
DQ38
DQ39
DQ40
V
SS
DQ41
DQ42
DQ43
DQ44
DQ45
V
DD
DQ46
DQ47
*CB4
*CB5
V
SS
NC
NC
V
DD
CAS
DQM4
Pin
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
Back
DQM5
*CS1
RAS
V
SS
A1
A3
A5
A7
A9
BA0
A11
V
DD
*CLK1
A12
V
SS
CKE0
*CS3
DQM6
DQM7
*A13
V
DD
NC
NC
*CB6
*CB7
V
SS
DQ48
DQ49
Pin
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
Back
DQ50
DQ51
V
DD
DQ52
NC
*V
REF
NC
V
SS
DQ53
DQ54
DQ55
V
SS
DQ56
DQ57
DQ58
DQ59
V
DD
DQ60
DQ61
DQ62
DQ63
V
SS
*CLK3
NC
**SA0
**SA1
**SA2
V
DD
* SAMSUNG ELECTRONICS CO., Ltd. reserves the right to change products and specifications without notice.
M366S1654CTS
PC133/PC100 Unbuffered DIMM
Rev. 0.1 Sept. 2001
PIN CONFIGURATION DESCRIPTION
Pin
Name
Input Function
CLK
System clock
Active on the positive going edge to sample all inputs.
CS
Chip select
Disables or enables device operation by masking or enabling all inputs except
CLK, CKE and DQM
CKE
Clock enable
Masks system clock to freeze operation from the next clock cycle.
CKE should be enabled at least one cycle prior to new command.
Disable input buffers for power down in standby.
CKE should be enabled 1CLK+t
SS
prior to valid command.
A0 ~ A12
Address
Row/column addresses are multiplexed on the same pins.
Row address : RA0 ~ RA12, Column address : CA0 ~ CA8
BA0 ~ BA1
Bank select address
Selects bank to be activated during row address latch time.
Selects bank for read/write during column address latch time.
RAS
Row address strobe
Latches row addresses on the positive going edge of the CLK with RAS low.
Enables row access & precharge.
CAS
Column address strobe
Latches column addresses on the positive going edge of the CLK with CAS low.
Enables column access.
WE
Write enable
Enables write operation and row precharge.
Latches data in starting from CAS, WE active.
DQM0 ~ 7
Data input/output mask
Makes data output Hi-Z, t
SHZ
after the clock and masks the output.
Blocks data input when DQM active. (Byte masking)
DQ0 ~ 63
Data input/output
Data inputs/outputs are multiplexed on the same pins.
V
DD
/V
SS
Power supply/ground
Power and ground for the input buffers and the core logic.
M366S1654CTS
PC133/PC100 Unbuffered DIMM
Rev. 0.1 Sept. 2001
DQM4
FUNCTIONAL BLOCK DIAGRAM
CS0
DQM0
DQM1
DQ0
DQ1
DQ2
DQ3
DQ4
DQ5
DQ6
DQ7
U0
DQ0
DQ1
DQ2
DQ3
DQ4
DQ5
DQ6
DQ7
DQ8
DQ9
DQ10
DQ11
DQ12
DQ13
DQ14
DQ15
DQ8
DQ9
DQ10
DQ11
DQ12
DQ13
DQ14
DQ15
LDQM
CS
UDQM
DQM5
DQ0
DQ1
DQ2
DQ3
DQ4
DQ5
DQ6
DQ7
U2
DQ32
DQ33
DQ34
DQ35
DQ36
DQ37
DQ38
DQ39
DQ8
DQ9
DQ10
DQ11
DQ12
DQ13
DQ14
DQ15
DQ40
DQ41
DQ42
DQ43
DQ44
DQ45
DQ46
DQ47
LDQM
CS
UDQM
A0 ~ An, BA0 & 1
CKE0
RAS
CAS
WE
SDRAM U0 ~ U3
SDRAM U0 ~ U3
SDRAM U0 ~ U3
SDRAM U0 ~ U3
SDRAM U0 ~ U3
10
DQn
Every DQpin of SDRAM
DQM6
CS2
DQM2
DQM3
DQ0
DQ1
DQ2
DQ3
DQ4
DQ5
DQ6
DQ7
U1
DQ16
DQ17
DQ18
DQ19
DQ20
DQ21
DQ22
DQ23
DQ8
DQ9
DQ10
DQ11
DQ12
DQ13
DQ14
DQ15
DQ24
DQ25
DQ26
DQ27
DQ28
DQ29
DQ30
DQ31
LDQM
CS
UDQM
DQM7
DQ0
DQ1
DQ2
DQ3
DQ4
DQ5
DQ6
DQ7
U3
DQ48
DQ49
DQ50
DQ51
DQ52
DQ53
DQ54
DQ55
DQ8
DQ9
DQ10
DQ11
DQ12
DQ13
DQ14
DQ15
DQ56
DQ57
DQ58
DQ59
DQ60
DQ61
DQ62
DQ63
LDQM
CS
UDQM
V
DD
Vss
Three o 0.1uF
per each SDRAM
To all SDRAMs
Capacitors
CLK1/3
U0/U2
10
CLK0/2
10
U1/U3
5pF
10pF
Serial PD
SDA
SCL
A1
A2
A0
SA1 SA2
SA0
WP
47K
M366S1654CTS
PC133/PC100 Unbuffered DIMM
Rev. 0.1 Sept. 2001
ABSOLUTE MAXIMUM RATINGS
Parameter
Symbol
Value
Unit
Voltage on any pin relative to Vss
V
IN
, V
OUT
-1.0 ~ 4.6
V
Voltage on V
DD
supply relative to Vss
V
DD
, V
DDQ
-1.0 ~ 4.6
V
Storage temperature
T
STG
-55 ~ +150
C
Power dissipation
P
D
4
W
Short circuit current
I
OS
50
mA
Permanent device damage may occur if "ABSOLUTE MAXIMUM RATINGS" are exceeded.
Functional operation should be restricted to recommended operating condition.
Exposure to higher than recommended voltage for extended periods of time could affect device reliability.
Note :
DC OPERATING CONDITIONS AND CHARACTERISTICS
CAPACITANCE
(V
DD
= 3.3V, T
A
= 23
C, f = 1MHz, V
REF
= 1.4V
200
mV)
Pin
Symbol
Min
Max
Unit
Address (A0 ~ A11, BA0 ~ BA1)
RAS, CAS, WE
CKE (CKE0)
Clock (CLK0, CLK2)
CS (CS0, CS2)
DQM (DQM0 ~ DQM7)
DQ (DQ0 ~ DQ63)
C
ADD
C
IN
C
CKE
C
CLK
C
CS
C
DQM
C
OUT
15
15
15
10
10
8
9
25
25
25
13
15
10
12
pF
pF
pF
pF
pF
pF
pF
Recommended operating conditions (Voltage referenced to V
SS
= 0V, T
A
= 0 to 70
C)
Parameter
Symbol
Min
Typ
Max
Unit
Note
Supply voltage
V
DD
, V
DDQ
3.0
3.3
3.6
V
Input logic high voltage
V
IH
2.0
3.0
V
DDQ
+0.3
V
1
Input logic low voltage
V
IL
-0.3
0
0.8
V
2
Output logic high voltage
V
OH
2.4
-
-
V
I
OH
= -2mA
Output logic low voltage
V
OL
-
-
0.4
V
I
OL
= 2mA
Input leakage current
I
LI
-10
-
10
uA
3
1. V
IH
(max) = 5.6V AC. The overshoot voltage duration is
3ns.
2. V
IL
(min) = -2.0V AC. The undershoot voltage duration is
3ns.
3. Any input 0V
V
IN
V
DDQ.
Input leakage currents include Hi-Z output leakage for all bi-directional buffers with Tri-State outputs.
Notes :
M366S1654CTS
PC133/PC100 Unbuffered DIMM
Rev. 0.1 Sept. 2001
1. Measured with outputs open.
2. Refresh period is 64ms.
3. Unless otherwise noted, input swing level is CMOS(V
IH
/V
IL
=V
DDQ
/V
SSQ
)
Notes :
DC CHARACTERISTICS
(Recommended operating condition unless otherwise noted, T
A
= 0 to 70
C)
Parameter
Symbol
Test Condition
Version
Unit
Note
- 7C
-7A
-1H
-1L
Operating current
(One bank active)
I
CC1
Burst length = 1
t
RC
t
RC
(min)
I
O
= 0 mA
440
400
400
400
mA
1
Precharge standby current
in power-down mode
I
CC2
P
CKE
V
IL
(max), t
CC
= 10ns
8
mA
I
CC2
PS
CKE & CLK
V
IL
(max), t
CC
=
8
Precharge standby current
in non power-down mode
I
CC2
N
CKE
V
IH
(min), CS
V
IH
(min), t
CC
= 10ns
Input signals are changed one time during 20ns
80
mA
I
CC2
NS
CKE
V
IH
(min), CLK
V
IL
(max), t
CC
=
Input signals are stable
40
Active standby current in
power-down mode
I
CC3
P
CKE
V
IL
(max), t
CC
= 10ns
24
mA
I
CC3
PS
CKE & CLK
V
IL
(max), t
CC
=
24
Active standby current in
non power-down mode
(One bank active)
I
CC3
N
CKE
V
IH
(min), CS
V
IH
(min), t
CC
= 10ns
Input signals are changed one time during 20ns
120
mA
I
CC3
NS
CKE
V
IH
(min), CLK
V
IL
(max), t
CC
=
Input signals are stable
100
mA
Operating current
(Burst mode)
I
CC4
I
O
= 0 mA
Page burst
4Banks activated
t
CCD
= 2CLKs
560
560
520
520
mA
1
Refresh current
I
CC5
t
RC
t
RC
(min)
880
800
760
760
mA
2
Self refresh current
I
CC6
CKE
0.2V
C
12
mA
L
6
mA
PDF 
ZIP