ChipFind - документация

Электронный компонент: S524A40X40

Скачать:  PDF   ZIP
S524A40X10/40X20/40X40
1K/2K/4K-bit
Serial EEPROM for Low Power
with software write protect
Data Sheet
2-1
OVERVIEW
The S524A40X10/40X20/40X40 serial EEPROM has a 1,024/2,048/4,096-bit (128/256/512-byte) capacity,
supporting the standard I
2
CTM-bus serial interface. It is fabricated using Samsung's most advanced CMOS
technology. It has been developed for low power and low voltage applications (1.8 V to 5.5 V). Important features
are a hardware-based write protection circuit for the entire memory area and software-based write protection logic
for the lower 128 bytes. Hardware-based write protection is controlled by the state of the write-protect (WP) pin.
The software-based method is one-time programmable and permanent. Using one-page write mode, you can
load up to 16 bytes of data into the EEPROM in a single write operation. Another significant feature of the
S524A40X10/40X20/40X40 is its support for fast mode and standard mode.
FEATURES
I
2
C-Bus Interface
Two-wire serial interface
Automatic word address increment
EEPROM
1K/2K/4K-bit (128/256/512-byte) storage area
16-byte page buffer
Typical 3 ms write cycle time with
auto-erase function
Hardware-based write protection for the entire
EEPROM (using the WP pin)
Software-based write protection for the lower
128-byte EEPROM
EEPROM programming voltage generated
on chip
1,000,000 erase/write cycles
100 years data retention
Operating Characteristics
Operating voltage
-- 1.8 V to 5.5 V
Operating current
-- Maximum write current: < 3 mA at 5.5 V
-- Maximum read current: < 200
A at 5.5 V
-- Maximum stand-by current: < 1
A at 5.5 V
Operating temperature range
-- 25C to + 70C (commercial)
-- 40C to + 85C (industrial)
Operating clock frequencies
-- 100 kHz at standard mode
-- 400 kHz at fast mode
Electrostatic discharge (ESD)
-- 5,000 V (HBM)
-- 500 V (MM)
Packages
8-pin DIP, SOP, and TSSOP
S524A40X10/40X20/40X40 SERIAL EEPROM DATA SHEET
2-2
Start/Stop
Logic
Slave Address
Comparator
Word Address
Pointer
Row
decoder
EEPROM
Cell Array
128 x 8 bits
256 x 8 bits
512 x 8 bits
HV Generation
Timing Control
Control Logic
Column Decoder
Data Register
D
OUT
and ACK
SCL
WP
SDA
A0
A1
A2
Figure 2-1. S524A40X10/40X20/40X40 Block Diagram
DATA SHEET S524A40X10/40X20/40X40 SERIAL EEPROM
2-3
S524A40X10/
40X20/40X40
V
CC
WP
SCL
SDA
A0
A1
A2
V
SS
NOTE:
The S524A40X10/40X20/40X40 is available
in 8-pin DIP, SOP, and TSSOP package.
Figure 2-2. Pin Assignment Diagram
Table 2-1. S524A40X10/40X20/40X40 Pin Descriptions
Name
Type
Description
Circuit
Type
A0, A1, A2
Input
Input pins for device address selection. To configure a device address,
these pins should be connected to the V
CC
or V
SS
of the device.
These pins are internally pulled down to V
SS
.
1
V
SS
Ground pin.
SDA
I/O
Bi-directional data pin for the I
2
C-bus serial data interface. Schmitt
trigger input and open-drain output. An external pull-up resistor must
be connected to V
CC.
Typical values for this pull-up resistor are 4.7 k
(100 kHz) and 1 k
(400 kHz).
3
SCL
Input
Schmitt trigger input pin for serial clock input.
2
WP
Input
Input pin for hardware write protection control. If you tie this pin to V
CC,
the write function is disabled to protect previously written data in the
entire memory; if you tie it to V
SS
, the write function is enabled.
This pin is internally pulled down to V
SS
.
1
V
CC
Single power supply.
NOTE: See the following page for diagrams of pin circuit types 1, 2, and 3.
S524A40X10/40X20/40X40 SERIAL EEPROM DATA SHEET
2-4
A0, A1,
A2, WP
Figure 2-3. Pin Circuit Type 1
SCL
Noise
Filter
Figure 2-4. Pin Circuit Type 2
SDA
V
SS
Data Out
Noise
Filter
Data In
Figure 2-5. Pin Circuit Type 3
DATA SHEET S524A40X10/40X20/40X40 SERIAL EEPROM
2-5
FUNCTION DESCRIPTION
I
2
C-BUS INTERFACE
The S524A40X10/40X20/40X40 supports the I
2
C-bus serial interface data transmission protocol. The two-wire bus
consists of a serial data line (SDA) and a serial clock line (SCL). The SDA and the SCL lines must be connected
to V
CC
by a pull-up resistor that is located somewhere on the bus.
Any device that puts data onto the bus is defined as the "transmitter" and any device that gets data from the bus
is the "receiver." The bus is controlled by a master device which generates the serial clock and start/stop
conditions, controlling bus access. Using the A0,A1 and A2 input pins, up to eight S524A40X10/40X20 (four for
S524A40X40) devices can be connected to the same I
2
C-bus as slaves (see Figure 2-6). Both the master and
slaves can operate as transmitter or receiver, but the master device determines which bus operating mode would
be active.
SDA
Bus Master
(Transmitter/
Receiver)
MCU
S524A40X20
Tx/Rx
A0 A1 A2
Slave 1
To V
CC
or V
SS
S524A40X20
Tx/Rx
A0 A1 A2
Slave 2
To V
CC
or V
SS
S524A40X20
Tx/Rx
A0 A1 A2
Slave 3
To V
CC
or V
SS
S524A40X20
Tx/Rx
A0 A1 A2
Slave 8
To V
CC
or V
SS
R
V
CC
R
V
CC
SCL
NOTE: The A0 does not affect the device address of the S524A40X40.
Figure 2-6. Typical Configuration (16 Kbits of Memory on the I
2
C-Bus)