Thick Film Hybrid IC
Ordering number : EN4478A
N3096HA (OT)/73093YO 5-2290 No. 4478-1/3
SANYO Electric Co.,Ltd. Semiconductor Bussiness Headquarters
TOKYO OFFICE Tokyo Bldg., 1-10, 1 Chome, Ueno, Taito-ku, TOKYO, 110 JAPAN
AF Power Amplifier (Split Power Supply)
(20 W + 20 W min, THD = 0.08%)
STK4131V
Specifications
Maximum Ratings
at Ta = 25C
Parameter
Symbol
Condition
Rating
Unit
Maximum supply voltage
V
CC
max
37
V
Thermal resistance
j-c
2.6
C/W
Junction temperature
T
j
max
150
C
Operating case temperature
T
c
125
C
Storage temperature
Tstg
30 to +125
C
Available time for load shorted
t
s
V
CC
= 24.5 V, R
L
= 8
, f = 50 Hz, P
O
= 20 W
2
s
Recommended Operating Conditions
at Ta = 25C
Parameter
Symbol
Condition
Rating
Unit
Recommended supply voltage
V
CC
24.5
V
Load resistance
R
L
8
Operating Characteristics
at Ta = 25C, V
CC
= 24.5 V, R
L
= 8
, Rg = 600
, VG = 40 dB, R
L
: non-inductive load
Rating
Parameter
Symbol
Condition
min
typ
max
Unit
Quiescent current
I
CCO
V
CC
= 29.5 V
20
40
100
mA
Output power
P
O
(1)
THD = 0.08%, f = 20 Hz to 20 kHz
20
W
P
O
(2)
V
CC
= 21.5 V, THD = 0.2%, R
L
= 4
, f = 1 kHz
20
W
Total harmonic distortion
THD
P
O
= 1 W, f = 1 kHz
0.08
%
+0
Frequency response
f
L
, f
H
P
O
= 1 W,
dB
20 to 50 k
Hz
3
Input resistance
r
i
P
O
= 1 W, f = 1 kHz
55
k
Output noise voltage
V
NO
V
CC
= 29.5 V, Rg = 10 k
1.2
mVrms
Neutral voltage
V
N
V
CC
= 29.5 V
70
0
+70
mV
Muting voltage
V
M
2
5
10
V
Features
Built-in muting circuit cuts off various kinds of pop
noises.
Current mirror circuit provides low distortion (THD =
0.08%).
Pin compatible with the STK4102II series, forming a
series of products with output powers from 15 W/ch to
120 W/ch.
Package Dimensions
unit : mm
4040
[STK4131V]
STK4131V
Specified Transformer Power Supply (RP-25 equivalent)
Notes
Use a constant voltage power supply for the test power supply unless otherwise noted.
Use the transformer power supply shown in the figure above when measuring the available time for load shorted and the output noise voltage.
The output noise voltage is the peak value measured with an averaging rms scale volt meter (VTVM). A 50 Hz AC stabilized power supply should be used
to eliminate the effects of AC primary line flicker noise when an AC power supply is used.
Equivalent Circuit
No. 4478-2/3
Sample Application Circuit: 20 W (minimum) 2-channel AF power amplifier
STK4131V
No. 4478-3/3
This catalog provides information as of November, 1996. Specifications and information herein are subject to
change without notice.
s
No products described or contained herein are intended for use in surgical implants, life-support systems, aerospace
equipment, nuclear power control systems, vehicles, disaster/crime-prevention equipment and the like, the failure of
which may directly or indirectly cause injury, death or property loss.
s
Anyone purchasing any products described or contained herein for an above-mentioned use shall:
x
Accept full responsibility and indemnify and defend SANYO ELECTRIC CO., LTD., its affiliates, subsidiaries and
distributors and all their officers and employees, jointly and severally, against any and all claims and litigation and all
damages, cost and expenses associated with such use:
Not impose any responsibility for any fault or negligence which may be cited in any such claim or litigation on
SANYO ELECTRIC CO., LTD., its affiliates, subsidiaries and distributors or any of their officers and employees
jointly or severally.
s
Information (including circuit diagrams and circuit parameters) herein is for example only; it is not guaranteed for
volume production. SANYO believes information herein is accurate and reliable, but no guarantees are made or implied
regarding its use or any infringements of intellectual property rights or other rights of third parties.
PDF 
ZIP