Liquid Crystal Displays Group
LQ10D368
TFT-LCD Module
(Model No.: LQ10D368)
Spec No.:
LD-13305B
Issue Date: December 6, 2002
P
RODUCT
S
PECIFICATIONS
RECORDS OF REVISION
LQ10D368
1/4
SPEC NO.
DATE
SUMMARY
NOTE
PAGE
LD-13305A 2002.9.25
1 1.Application
Added the sentence, " (This specification is only
)"
2
3.Mechanical
Specifications
Revised mass value
550
20g 520g(max)
Changed the description of unit outline dimensions
(D)11.0mm
(D)11.5mm(MAX)
Surface treatment
Delete"Haze value28"
3
4.Input
terminals
Changed "Used connector"
DF9BA-31P-1V
DF9MA-31P-1V
(Corresponding connector is not changed)
Changed function of 29,30pin
5.0V power supply 3.3/5.0V power supply
Corrected the description about the connection between
shielding case and GND
The shielding case is not connected with GND.
The shielding case is connected with GND.
4
5.Absolute Maximum Ratings
Changed storage temp. and operating temp.
Storage temperature
Tstg
-25+70 -30+70
Operating temerature(Ambient)
Topa
0+50
-10+65
5
6.Electrical
Characteristics
6-1 TFT-LCDpaneldriving
Changed "Supply voltage"
Min
Typ
Max
Min
Typ
Max
Unit
+4.5
+5.0
+5.5
+3.0 +3.3 +5.0
+5.5
V
Changed "Current dissipation"
Typ
Max
Typ
Max
Unit
VCC=5.0V 280
450
150 230
mA
VCC=3.3V
180
270
mA
Changed the remark of "Permissive input ripple voltage"
Deleted "Vcc=+5.0V"
sharp
RECORDS OF REVISION
LQ10D368
2/4
SPEC NO.
DATE
SUMMARY
NOTE
PAGE
LD-13305A 2002.9.25
5
Corrected "Input current"
Parameter
Symbol
Max Remark
Symbol
Max Remark
Input I
OL1
1.0
A
Note4
I
OL1
1.0
A
Note4
current I
OL2
60.0
A
Note5
I
OL2
10
A
Note5
(Low)
I
OL3
800
A
Note6
Input I
OH1
1.0
A
Note6
I
OH1
1.0
A
Note7
current I
OH2
60.0
A
Note7
I
OH2
300
A
Note8
(High)
I
OH3
800
A
Note9
Note4CK,R0R5,G0G5,B0B5, Note4CK,R0R5,G0G5,B0B5,
Hsync,Vsync,ENAB Hsync,Vsync
Note5R/L Note5U/D,ENAB
Note6CK, R0R5,G0G5,B0B5, Note6R/L
Hsync,Vsync
Note7CK,R0R5,G0G5,B0B5,
Note7ENAB,U/D Hsync,Vsync,R/L
Note8ENAB
Note9U/D
Note1Changed "Vcc-turm-on conditions"
T1
15ms 0T115ms
0
T210ms 0T210ms
0
T320ms 0T3100ms
0
T41s 0T41s
1s
T5 T5200ms
Note1Changed "Vcc-dip condition"
2.7V
Vcc4.5V td10ms
2.5V Vcc td10ms
Note2Changed the typical current situation
VCC=+5.0V
VCC=+3.3V/5.0V
Note2Corrected the figure of typical current situation
6
6-2 Backlight driving
According with the change of operating temperature spec,
added "Kick off voltage" value at Ta= -10
Kick off voltage
Max 1500Vrms(Ta= -10)
Changed "Lamp life time"Typ 50000 h Min 50000h
T
0.3V
VCC
T1
T
4.5V
0.3V
VCC
T
4.5V
T
2.8V
T
0.3V
VCC
T1
T
0.9VCC
0.3V
VCC
T
0.9VCC
Signal
Signal
T
2.7V
sharp
RECORDS OF REVISION
LQ10D368
3/4
SPEC NO.
DATE
SUMMARY
NOTE
PAGE
LD-13305A 2002.9.25
6
Note2Corrected the condition
At the condition of Y
L
=200cd/m
2
At the condition of I
L
=6.0mArms
7
7 Timing Characteristics of input signals
Corrected "Timing characteristics"
Vertical sync. signal
Cycle
TV(Mode:400line)
Min 445 446line
13
9. Optical Characteristics
Changed the condition of "Viewing Angle Range"
(Widening viewing angle range)
CR
5 CR10
Changed the measurement condition
Changed the remark of chromaticity and luminance
Added
"I
L
=6.0mArms, f=35KHz"
(typical condition
I
L
=6.0mArms)
(conditionI
L
=6.0mArms)
15
11. Handling Precautions
Changed "Handling precautions"
h)Laminated film Protection film
Deleted"Ionized air shall"
Added "j)"
Added "m)"
Added "n)"
12.Packing
form
Corrected packing form
Piling number of cartons7cartons 8cartons
Carton size 298(W)362(D)295(h)
497(W)318(D)227(h)
Total mass of one carton filled with
full modules
8.0kg 7.8kg
Packing form is shown Fig.7 Fig.4
sharp
PDF 
ZIP