1
ILX535K
22 pin DIP (Plastic)
E97446D98-PS
5300 pixel
3 line CCD Linear Sensor (Color)
Description
The ILX535K is a reduction type CCD linear sensor
developed for color image scanner. The distance
between lines is only 4 line (32m). This sensor reads
A4-size documents at a density of 600DPI.
Features
Number of effective pixels: 15900 pixels
(5300 pixels
3)
Pixel size:
8m
8m (8m pitch)
Distance between line: 32m (4 Lines)
Number of output
3 (R, G, B)
Single-sided readout
Clamp circuit are on-chip
Ultra high sensitivity/Ultra low lag
Single 12V power supply
Maximum data rate:
9MHz (3MHz
3)
Input Clock Pulse:
CMOS 5V drive
Package:
22 pin Plastic-DIP (400 mil)
Absolute Maximum Ratings
Supply voltage
V
DD
15
V
Operating temperature
10 to +55
C
Storage temperature
30 to +80
C
Pin Configuration (Top View)
Block Diagram
Sony reserves the right to change products and specifications without prior notice. This information does not convey any license by
any implication or otherwise under any patents or other right. Application circuits shown, if any, are typical examples illustrating the
operation of the devices. Sony cannot assume responsibility for any problems arising out of the use of these circuits.
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
1
5300
R
1
5300
G
1
5300
B
1
GND
GND
V
OUT-B
NC
NC
NC
NC
NC
2
ROG
-R
ROG
-G
RS
V
OUT-R
V
DD
NC
NC
NC
NC
NC
1
ROG
-B
V
OUT-G
D14
D15
D63
S1
Read Out Gate
CCD Register
S5300
Driver
D14
D15
D63
S1
Read Out Gate
CCD Register
S5300
Driver
D14
D15
D63
S1
Read Out Gate
CCD Register
S5300
Driver
Driver
Blue
Green
Red
ROG
-B
ROG
-G
ROG
-R
V
OUT-B
V
OUT-G
V
OUT-R
V
DD
2
GND
RS
1
20
4
13
12
10
11
3
2
1
14
21
Clamp Pulse
Generator
Clamp
Clamp
Clamp
For the availability of this product, please contact the sales office.
3
ILX535K
Electrooptical Characteristics (Note 1)
Ta = 25C, V
DD
= 12V, f
RS
= 1MHz, Input clock = 5Vp-p,
Light source = 3200K, IR cut filter CM-500S (t = 1.0mm)
Item
Symbol
Min.
Typ.
Max.
Unit
Remarks
Sensitivity
Sensitivity nonuniformity
Saturation output voltage
Saturation
exposure
Dark voltage average
Dark signal nonuniformity
Image lag
Supply current
Total transfer efficiency
Output impedance
Offset level
R
R
R
G
R
B
PRNU
V
SAT
SE
R
SE
G
SE
B
V
DRK
DSNU
IL
I
VDD
TTE
Z
O
V
OS
6.2
12.3
7.5
--
2.0
0.15
0.10
0.12
--
--
--
--
92
--
--
9.5
19
11.5
4
2.5
0.26
0.13
0.21
2
4
0.02
30
98
300
6.3
12.8
25.6
15.5
20
--
--
--
--
5
12
--
50
--
--
--
V/(lx s)
%
V
lx s
mV
mV
%
mA
%
V
Note 2
Note 3
Note 4
Note 5
Note 6
Note 6
Note 7
--
--
--
Note 8
Red
Green
Blue
Red
Green
Blue
Notes
1) In accordance with the given electrooptical characteristics, the black level is defined as the average value
of D2, D3 to D12.
2) For the sensitivity test light is applied with a uniform intensity of illumination.
3) PRNU is defined as indicated below. Ray incidence conditions are the same as for Note 2.
V
OUT-G
= 500mV (Typ.)
PRNU =
100 [%]
Where the 5300 pixels are divided into blocks of 100. The maximum output of each block is set to V
MAX
,
the minimum output to V
MIN
and the average output to V
AVE
.
4) Use below the minimum value of the saturation output voltage.
5) Saturation exposure is defined as follows.
SE =
Where R indicates R
R
, R
G
, R
B
, and SE indicates SE
R
, SE
G
, SE
B
.
6) Optical signal accumulated time
int stands at 5ms.
7) V
OUT-G
= 500mV (Typ.)
8) Vos is defined as the right side.
V
OUT
indicates V
OUT-R
, V
OUT-G
, and V
OUT-B
.
(V
MAX
V
MIN
) /2
V
AVE
V
OS
V
OUT
GND
V
SAT
R
PDF 
ZIP
