1
SLD1135VS
E98273A86-PS
650nm Index-Guided Red Laser Diode
Description
The SLD1135VS is a index-guided red laser diode
for Laser pointer. The wavelength is 20nm shorter
than SLD1122VS.
Features
Small astigmatism (7m typ.)
Small package (
5.6mm)
Single longitudinal mode
Low operating voltage (2.5V Max)
Max operating temperature = 40C (Case temperature)
Applications
Laser pointer
Structure
AlGaInP MQW laser diode
PIN photodiode to monitor laser beam output
Recommend Optical Power Output
5mW
Absolute Maximum Ratings (Tc = 25C)
Optical power output
Po
5
mW
Reverse voltage
V
R
LD
2
V
PD
15
V
Operating temperature
Topr
10 to +40
C
Storage temperature
Tstg
40 to +85
C
Sony reserves the right to change products and specifications without prior notice. This information does not convey any license by
any implication or otherwise under any patents or other right. Application circuits shown, if any, are typical examples illustrating the
operation of the devices. Sony cannot assume responsibility for any problems arising out of the use of these circuits.
M-294
Pin Configuration
3
LD
1
2
PD
COMMON
2
1
3
Bottom View
1. LD cathode
2. PD anode
3. COMMON
Connection Diagram
2
SLD1135VS
Electrical and Optical Characteristics (Tc = 25C)
Tc: Case temperature
Item
Threshold current
Operating current
Operating voltage
Wavelength
Radiation
angle
Positional
accuracy
Differential efficiency
Astigmatism
Monitor current
Ith
Iop
Vop
p
//
X,
Y,
Z
//
D
As
Imon
Po = 5mW
Po = 5mW
Po = 5mW
Po = 5mW
Po = 5mW
Po = 5mW
Po = 5mW
Po = 5mW, V
R
= 5V
22
5
0.3
0.05
30
35
2.2
650
30
7
0.6
7
0.1
40
45
2.5
660
40
12
150
3
3
0.9
15
0.25
mA
mA
V
nm
degree
degree
m
degree
degree
mW/mA
m
mA
Symbol
Conditions
Min.
Typ.
Max.
Unit
Perpendicular
Parallel
Position
Angle
Handling Precautions
(1) Eye protection against laser beams
The optical output of laser diodes ranges from
several mW to 4W. However the optical power
density of the laser beam at the diode chip
reaches 1MW/cm
2
. Unlike gas lasers, since
laser diode beams are divergent, uncollimated
laser diode beams are fairly safe at a laser
diode. For observing laser beams, ALWAYS
use safety goggles that block infrared rays.
Usage of IR scopes, IR cameras and
fluorescent plates is also recommended for
monitoring laser beams safely.
Safety goggles for
protection from laser beam
IR fluorescent plate
Optical
material
Lens
Laser diode
Optical board
Optical power output control device
Temperature control device
(2) Prevention of surge current and electrostatic discharge
Laser diode is most sensitive to electrostatic discharge among semiconductors. When a large current is
passed through the laser diode even for an extremely short time (in the order of nanosecond), the strong light
emitted from the laser diode promotes deterioration and then laser diodes are destroyed. Therefore, note that
the surge current should not flow the laser diode driving circuit from switches and others. Also, if the laser
diode is handled carelessly, it may be destructed instantly because electrostatic discharge is easily applied by
a human body. Be great careful about excess current and electrostatic discharge.
PDF 
ZIP