HCC/HCF4041UB
June 1989
QUAD TRUE/COMPLEMENT BUFFER
.
BALANCED SINK AND SOURCE CURRENT ;
APPROXIMATELY 4 TIMES STANDARD "B"
DRIVE
.
EQUALIZED DELAY TO TRUE AND COMPLE-
MENT OUTPUTS
.
QUIESCENT CURRENT SPECIFIED TO 20V
FOR HCC DEVICE
.
5V, 10V AND 15V PARAMETRIC RATINGS
.
INPUT CURRENT OF 100nA AT 18V AND 25
C
FOR HCC DEVICE
.
100 % TESTED FOR QUIESCENT CURRENT
.
MEETS ALL REQUIREMENTS OF JEDEC TEN-
TATIVE STANDARD N
13A, "STANDARD SPE-
CIFICATIONS FOR DESCRIPTION OF "B"
SERIES CMOS DEVICES"
DESCRIPTION
The HCC4041UB (extended temperature range)
and HCF4041UB (intermediate temperature range)
are monolithic integrated circuits, available in 14-
lead dual in-line plastic or ceramic package and
plastic micro package.
The HCC/HCF4041UB types are quad true/comple-
ment buffers consisting of n- and p-channel units
having low channel resistance and high current
(sourcing and sinking) capability. The HCC/-
HCF4041UB is intended for use as a buffer, line
driver, or COS/MOS-to-TTL driver. It can be used as
an ultra-low power resistor-network driver for A/D
and D/A conversion, as a transmission-line driver,
and in other applications where high noise immunity
and low-power dissipation are primary design re-
quirements.
EY
(Plastic Package)
F
(Ceramic Frit Seal Package)
M1
(Micro Package)
C1
(Plastic Chip Carrier)
ORDER CODES :
HCC4041BF
HCF4041BM1
HCF4041BEY
HCF4041BC1
PIN CONNECTIONS
1/12
ABSOLUTE MAXIMUM RATINGS
Symbol
Parameter
Value
Unit
V
DD
*
Supply Voltage : HC C Types
H C F Types
0.5 to + 20
0.5 to + 18
V
V
V
i
Input Voltage
0.5 to V
DD
+ 0.5
V
I
I
DC Input Current (any one input)
10
mA
P
t o t
Total Power Dissipation (per package)
Dissipation per Output Transistor
for T
o p
= Full Package-temperature Range
200
100
mW
mW
T
o p
Operating Temperature : HCC Types
H CF Types
55 to + 125
40 to + 85
C
C
T
s t g
Storage Temperature
65 to + 150
C
Stresses above those listed under "Absolute Maximum Ratings" may cause permanent damage to the device. This is a stress
rating only and functional operation of the device at these or any other conditions above those indicated in the operational sections
of this specification is not implied. Exposure to absolute maximum rating conditions for external periods may affect device reliability.
* All voltage values are referred to V
SS
pin voltage.
FUNCTIONAL DIAGRAM
RECOMMENDED OPERATING CONDITIONS
Symbol
Parameter
Value
Unit
V
DD
Supply Voltage : HC C Types
H C F Types
3 to + 18
3 to + 15
V
V
V
I
Input Voltage
0 to V
DD
V
T
o p
Operating Temperature : H CC Types
H C F Types
55 to + 125
40 to + 85
C
C
HCC/HCF4041UB
2/12
SCHEMATIC DIAGRAM
STATIC ELECTRICAL CHARACTERISTICS (over recommended operating conditions)
Test Conditions
Value
V
I
V
O
|I
O
|
V
D D
T
L o w
*
25
C
T
Hi g h
*
Symbol
Parameter
(V)
(V)
(
A)
(V)
Min. Max. Min. Typ. Max. Min. Max.
Unit
I
L
Quiescent
Current
HCC
Types
0/ 5
5
1
0.02
1
30
A
0/10
10
2
0.02
2
60
0/15
15
4
0.02
4
120
0/20
20
20
0.04
20
600
HCF
Types
0/ 5
5
4
0.02
4
30
0/10
10
8
0.02
8
60
0/15
15
16
0.02
16
120
V
O H
Output High
Voltage
0/ 5
< 1
5
4.95
4.95
4.95
V
0/10
< 1
10
9.95
9.95
9.95
0/15
< 1
15
14.95
14.95
14.95
V
O L
Output Low
Voltage
5/0
< 1
5
0.05
0.05
0.05
V
10/0
< 1
10
0.05
0.05
0.05
15/0
< 1
15
0.05
0.05
0.05
V
IH
Input High
Voltage
0.5/4.5
< 1
5
4
4
4
V
1/9
< 1
10
8
8
8
1.5/13.5
< 1
15
12.5
12.5
12.5
* T
Lo w
= 55
C for HCC device : 40
C for HCF device.
* T
High
= + 125
C for HCC device : + 85
C for HCF device.
The Noise Margin for both "1" and " 0" level is : 1V min. with V
DD
= 5V, 2V min. with V
DD
= 10V, 2.5V min. with V
DD
= 15V.
HCC/HCF4041UB
3/12
STATIC ELECTRICAL CHARACTERISTICS (continued)
Test Conditions
Value
V
I
V
O
|I
O
|
V
D D
T
L o w
*
25
C
T
Hi g h
*
Symbol
Parameter
(V)
(V)
(
A)
(V)
Min. Max. Min. Typ. Max. Min. Max.
Unit
V
IL
Input Low
Voltage
4.5/0.5
< 1
5
1
1
1
V
9/1
< 1
10
2
2
2
13.5/1.5
< 1
15
2.5
2.5
2.5
I
O H
Output
Drive
Current
HCC
Types
0/ 5
2.5
5
8.4
6.4 12.8
4.6
mA
0/ 5
4.6
5
2.1
1.6 3.2
1.2
0/10
9.5
10
6.25
5
10
3.5
0/15
13.5
15
24
19
38
13
HCF
Types
0/ 5
2.5
5
6.8
5.44 12.8
4.08
0/ 5
4.6
5
1.7
1.36 3.2
1.02
0/10
9.5
10
5.31
4.25 10
3.18
0/15
13.5
15
20.18
16.15
38
12.11
I
O L
Output
Sink
Current
HCC
Types
0/ 5
0.4
5
2.1
1.6
3.2
1.2
0/10
0.5
10
6.25
5
10
3.5
0/15
1.5
15
24
19
38
13
HCF
Types
0/ 5
0.4
5
1.7
1.36
3.2
1.02
0/10
0.5
10
5.31
4.25
10
3.18
0/15
1.5
15
20.18
16.15
38
12.11
I
IH
, I
IL
Input
leakage
Current
HCC
Types
0/18
Any Input
18
0.1
10
5
0.1
1
A
HCF
Types
0/15
15
0.3
10
5
0.3
1
C
I
Input Capacitance
Any Input
15
22.5
pF
* T
Lo w
= 55
C for HCC device : 40
C for HCF device.
* T
High
= + 125
C for HCC device : + 85
C for HCF device.
The Noise Margin for both "1" and " 0" level is : 1V min. with V
DD
= 5V, 2V min. with V
DD
= 10V, 2.5V min. with V
DD
= 15V.
DYNAMIC ELECTRICAL CHARACTERISTICS (T
amb
= 25
C, C
L
= 50pF, R
L
= 200k
,
typical temperature coefficient for all V
DD
values is 0.3 %/
C, all input rise and fall times = 20ns)
Test Conditions
Val ue
Symbol
Parameter
V
D D
(V)
Min.
Typ.
Max.
Unit
t
PL H
, t
PHL
Propagation Delay Time
5
60
120
ns
10
35
70
15
25
50
t
T HL
, t
TL H
Transition Time
5
40
80
ns
10
20
40
15
15
30
HCC/HCF4041UB
4/12
Minimum Output High (source) Current Charac-
teristics.
Typical Output Low (sink) Current.
Minimum Output Low (sink) Current Charac-
teristics.
Typical Output High (source) Current Charac-
teristics.
Typical Transition Time vs. Load Capacitance.
Typical Propagation Delay Time vs. Load Capacit-
ance.
HCC/HCF4041UB
5/12
Minimum and Maximum Transfer Characteristics-true Output-and Test Circuit.
Minimum Maximum Transfer Characteristics Complement Output-and Test Circuit.
Typical Power Dissipation vs. Input Rise and Fall
Time per Output Pair.
Typical Power Dissipation vs. Frequency per Out-
put Pair.
HCC/HCF4041UB
6/12
TEST CIRCUITS
Quiescent Device Current.
Noise Immunity.
Input Leakage Current.
HCC/HCF4041UB
7/12
Plastic DIP14 MECHANICAL DATA
DIM.
mm
inch
MIN.
TYP.
MAX.
MIN.
TYP.
MAX.
a1
0.51
0.020
B
1.39
1.65
0.055
0.065
b
0.5
0.020
b1
0.25
0.010
D
20
0.787
E
8.5
0.335
e
2.54
0.100
e3
15.24
0.600
F
7.1
0.280
I
5.1
0.201
L
3.3
0.130
Z
1.27
2.54
0.050
0.100
P001A
HCC/HCF4041UB
8/12
Ceramic DIP14/1 MECHANICAL DATA
DIM.
mm
inch
MIN.
TYP.
MAX.
MIN.
TYP.
MAX.
A
20
0.787
B
7.0
0.276
D
3.3
0.130
E
0.38
0.015
e3
15.24
0.600
F
2.29
2.79
0.090
0.110
G
0.4
0.55
0.016
0.022
H
1.17
1.52
0.046
0.060
L
0.22
0.31
0.009
0.012
M
1.52
2.54
0.060
0.100
N
10.3
0.406
P
7.8
8.05
0.307
0.317
Q
5.08
0.200
P053C
HCC/HCF4041UB
9/12
SO14 MECHANICAL DATA
DIM.
mm
inch
MIN.
TYP.
MAX.
MIN.
TYP.
MAX.
A
1.75
0.068
a1
0.1
0.2
0.003
0.007
a2
1.65
0.064
b
0.35
0.46
0.013
0.018
b1
0.19
0.25
0.007
0.010
C
0.5
0.019
c1
45
(typ.)
D
8.55
8.75
0.336
0.344
E
5.8
6.2
0.228
0.244
e
1.27
0.050
e3
7.62
0.300
F
3.8
4.0
0.149
0.157
G
4.6
5.3
0.181
0.208
L
0.5
1.27
0.019
0.050
M
0.68
0.026
S
8
(max.)
P013G
HCC/HCF4041UB
10/12
PLCC20 MECHANICAL DATA
DIM.
mm
inch
MIN.
TYP.
MAX.
MIN.
TYP.
MAX.
A
9.78
10.03
0.385
0.395
B
8.89
9.04
0.350
0.356
D
4.2
4.57
0.165
0.180
d1
2.54
0.100
d2
0.56
0.022
E
7.37
8.38
0.290
0.330
e
1.27
0.050
e3
5.08
0.200
F
0.38
0.015
G
0.101
0.004
M
1.27
0.050
M1
1.14
0.045
P027A
HCC/HCF4041UB
11/12
Information furnished is believed to be accurate and reliable. However, SGS-THOMSON Microelectronics assumes no responsability for the
consequences of use of such information nor for any infringement of patents or other rights of third parties which may results from its use. No
license is granted by implication or otherwise under any patent or patent rights of SGS-THOMSON Microelectronics. Specifications mentioned
in this publication are subject to change without notice. This publication supersedes and replaces all information previously supplied.
SGS-THOMSON Microelectronics products are not authorized for use as critical components in life support devices or systems without express
written approval of SGS-THOMSON Microelectonics.
1994 SGS-THOMSON Microelectronics - All Rights Reserved
SGS-THOMSON Microelectronics GROUP OF COMPANIES
Australia - Brazil - France - Germany - Hong Kong - Italy - Japan - Korea - Malaysia - Malta - Morocco - The Netherlands -
Singapore - Spain - Sweden - Switzerland - Taiwan - Thailand - United Kingdom - U.S.A
HCC/HCF4041UB
12/12
PDF 
ZIP