1/19

PRELIMINARY DATA

February 2000

This is preliminary information on a new product now in development or undergoing evaluation. Details are subject to change without notice.

M24256-B
M24128-B

256/128 Kbit Serial I C Bus EEPROM

With Three Chip Enable Lines

Compatible with I

C Extended Addressing

Two Wire I

C Serial Interface

Supports 400 kHz Protocol

Single Supply Voltage:

4.5V to 5.5V for M24xxx-B

2.5V to 5.5V for M24xxx-BW

1.8V to 3.6V for M24xxx-BR

Hardware Write Control

BYTE and PAGE WRITE (up to 64 Bytes)

RANDOM and SEQUENTIAL READ Modes

Self-Timed Programming Cycle

Automatic Address Incrementing

Enhanced ESD/Latch-Up Behavior

100000 Erase/Write Cycles (minimum)

40 Year Data Retention (minimum)

DESCRIPTION
These I

C-compatible electrically erasable pro-

grammable memory (EEPROM) devices are orga-
nized as 32Kx8 bits (M24256-B) and 16Kx8 bits
(M24128-B).
These memory devices are compatible with the
I

C extended memory standard. This is a two wire

serial interface that uses a bi-directional data bus
and serial clock. The memory carries a built-in 4-
bit unique Device Type Identifier code (1010) in
accordance with the I

C bus definition.

Figure 1. Logic Diagram

AI02809

SDA

VCC

M24256-B
M24128-B

SCL

VSS

E0-E2

Table 1. Signal Names

E0, E1, E2

Chip Enable Inputs

SDA

Serial Data/Address Input/
Output

SCL

Serial Clock

Write Control

VCC

Supply Voltage

VSS

Ground

PSDIP8 (BN)

0.25 mm frame

SO8 (MN)

150 mil width

TSSOP8 (DW)

169 mil width

TSSOP14 (DL)

169 mil width

M24256-B, M24128-B

2/19

The memory behaves as a slave device in the I

protocol, with all memory operations synchronized
by the serial clock. Read and Write operations are
initiated by a START condition, generated by the
bus master. The START condition is followed by a
Device Select Code and RW bit (as described in
Table 3), terminated by an acknowledge bit.
When writing data to the memory, the memory in-
serts an acknowledge bit during the 9

bit time,

following the bus master's 8-bit transmission.
When data is read by the bus master, the bus
master acknowledges the receipt of the data byte
in the same way. Data transfers are terminated by
a STOP condition after an Ack for WRITE, and af-
ter a NoAck for READ.
Power On Reset: V

Lock-Out Write Protect

In order to prevent data corruption and inadvertent
write operations during power up, a Power On Re-

Figure 2A. PSDIP8 Connections

Figure 2B. SO8 and TSSOP8 Connections

SDA

VSS

SCL

VCC

AI02810

M24256-B
M24128-B

2
3

7
6

AI02811

3
4

8
7

6
5

SDA

VSS

SCL

VCC

M24256-B
M24128-B

Figure 2C. TSSOP14 Connections

Note: 1. NC = Not Connected

AI02812

SDA

VSS

SCL

M24256-B
M24128-B

VCC

Table 2. Absolute Maximum Ratings

Note: 1. Except for the rating "Operating Temperature Range", stresses above those listed in the Table "Absolute Maximum Ratings" may

cause permanent damage to the device. These are stress ratings only, and operation of the device at these or any other conditions
above those indicated in the Operating sections of this specification is not implied. Exposure to Absolute Maximum Rating condi-
tions for extended periods may affect device reliability. Refer also to the ST SURE Program and other relevant quality documents.

2. MIL-STD-883C, 3015.7 (100 pF, 1500

)

Symbol

Parameter

Value

Unit

Ambient Operating Temperature

-40 to 125

STG

Storage Temperature

-65 to 150

LEAD

Lead Temperature during Soldering

PSDIP8: 10 seconds
SO8: 40 seconds
TSSOP8: 40 seconds
TSSOP14: 40 seconds

260
215
215
215

Input or Output range

-0.6 to 6.5

Supply Voltage

-0.3 to 6.5

ESD

Electrostatic Discharge Voltage (Human Body model)

4000

3/19

M24256-B, M24128-B

set (POR) circuit is included. The internal reset is
held active until the V

voltage has reached the

POR threshold value, and all operations are dis-
abled the device will not respond to any com-
mand. In the same way, when V

drops from the

operating voltage, below the POR threshold value,
all operations are disabled and the device will not
respond to any command. A stable and valid V

must be applied before applying any logic signal.

SIGNAL DESCRIPTION
Serial Clock (SCL)
The SCL input pin is used to strobe all data in and
out of the memory. In applications where this line
is used by slaves to synchronize the bus to a slow-
er clock, the master must have an open drain out-
put, and a pull-up resistor must be connected from
the SCL line to V

. (Figure 3 indicates how the

value of the pull-up resistor can be calculated). In
most applications, though, this method of synchro-
nization is not employed, and so the pull-up resis-
tor is not necessary, provided that the master has
a push-pull (rather than open drain) output.
Serial Data (SDA)
The SDA pin is bi-directional, and is used to trans-
fer data in or out of the memory. It is an open drain
output that may be wire-OR'ed with other open
drain or open collector signals on the bus. A pull
up resistor must be connected from the SDA bus
to V

. (Figure 3 indicates how the value of the

pull-up resistor can be calculated).
Chip Enable (E2, E1, E0)
These chip enable inputs are used to set the value
that is to be looked for on the three least significant
bits (b3, b2, b1) of the 7-bit device select code.
These inputs must be tied directly to V

or V

establish the device select code. When uncon-
nected, the E2, E1 and E0 inputs are internally
read as V

(see Table 7 and Table 8)

Write Control (WC)
The hardware Write Control pin (WC) is useful for
protecting the entire contents of the memory from
inadvertent erase/write. The Write Control signal is
used to enable (WC=V

) or disable (WC=V

)

write instructions to the entire memory area. When
unconnected, the WC input is internally read as
V

, and write operations are allowed.

When WC=1, Device Select and Address bytes
are acknowledged, Data bytes are not acknowl-
edged.
Please see the Application Note

AN404 for a more

detailed description of the Write Control feature.

DEVICE OPERATION
The memory device supports the I

C protocol.

This is summarized in Figure 4, and is compared
with other serial bus protocols in Application Note
AN1001. Any device that sends data on to the bus
is defined to be a transmitter, and any device that
reads the data to be a receiver. The device that
controls the data transfer is known as the master,
and the other as the slave. A data transfer can only
be initiated by the master, which will also provide
the serial clock for synchronization. The memory
device is always a slave device in all communica-
tion.
Start Condition
START is identified by a high to low transition of
the SDA line while the clock, SCL, is stable in the
high state. A START condition must precede any
data transfer command. The memory device con-
tinuously monitors (except during a programming

Figure 3. Maximum R

Value versus Bus Capacitance (C

BUS

) for an I

C Bus

AI01665

VCC

CBUS

SDA

MASTER

SCL

CBUS

100

CBUS (pF)

Maximum

value

)

1000

fc = 400kHz

fc = 100kHz

M24256-B, M24128-B

4/19

cycle) the SDA and SCL lines for a START condi-
tion, and will not respond unless one is given.
Stop Condition
STOP is identified by a low to high transition of the
SDA line while the clock SCL is stable in the high
state. A STOP condition terminates communica-
tion between the memory device and the bus mas-
ter. A STOP condition at the end of a Read
command, after (and only after) a NoAck, forces
the memory device into its standby state. A STOP
condition at the end of a Write command triggers
the internal EEPROM write cycle.
Acknowledge Bit (ACK)
An acknowledge signal is used to indicate a suc-
cessful byte transfer. The bus transmitter, whether
it be master or slave, releases the SDA bus after
sending eight bits of data. During the 9

clock

pulse period, the receiver pulls the SDA bus low to
acknowledge the receipt of the eight data bits.

Data Input
During data input, the memory device samples the
SDA bus signal on the rising edge of the clock,
SCL. For correct device operation, the SDA signal
must be stable during the clock low-to-high transi-
tion, and the data must change

only when the SCL

line is low.
Memory Addressing
To start communication between the bus master
and the slave memory, the master must initiate a
START condition. Following this, the master sends
the 8-bit byte, shown in Table 3, on the SDA bus
line (most significant bit first). This consists of the
7-bit Device Select Code, and the 1-bit Read/Write
Designator (RW). The Device Select Code is fur-
ther subdivided into: a 4-bit Device Type Identifier,
and a 3-bit Chip Enable "Address" (E2, E1, E0).
To address the memory array, the 4-bit Device
Type Identifier is 1010b.

Figure 4. I

C Bus Protocol

SCL

SDA

SCL

SDA

START

CONDITION

SDA

INPUT

SDA

CHANGE

AI00792

STOP

CONDITION

MSB

ACK

START

CONDITION

SCL

MSB

ACK

STOP

CONDITION

5/19

M24256-B, M24128-B

Up to eight memory devices can be connected on
a single I

C bus. Each one is given a unique 3-bit

code on its Chip Enable inputs. When the Device
Select Code is received on the SDA bus, the mem-
ory only responds if the Chip Select Code is the
same as the pattern applied to its Chip Enable
pins.
The 8

bit is the RW bit. This is set to `1' for read

and `0' for write operations. If a match occurs on
the Device Select Code, the corresponding mem-
ory gives an acknowledgment on the SDA bus dur-
ing the 9

bit time. If the memory does not match

the Device Select Code, it deselects itself from the
bus, and goes into stand-by mode.
There are two modes both for read and write.
These are summarized in Table 6 and described
later. A communication between the master and
the slave is ended with a STOP condition.
Each data byte in the memory has a 16-bit (two
byte wide) address. The Most Significant Byte (Ta-
ble 4) is sent first, followed by the Least significant
Byte (Table 5). Bits b15 to b0 form the address of
the byte in memory. Bit b15 is treated as a Don't
Care bit on the M24256-B memory. Bits b15 and
b14 are treated as Don't Care bits on the M24128-
B memory.

Write Operations
Following a START condition the master sends a
Device Select Code with the RW bit set to '0', as
shown in Table 6. The memory acknowledges this,
and waits for two address bytes. The memory re-

sponds to each address byte with an acknowledge
bit, and then waits for the data byte.
Writing to the memory may be inhibited if the WC
input pin is taken high. Any write command with
WC=1 (during a period of time from the START
condition until the end of the two address bytes)
will not modify the memory contents, and the ac-
companying data bytes will

not be acknowledged,

as shown in Figure 5.
Byte Write
In the Byte Write mode, after the Device Select
Code and the address bytes, the master sends
one data byte. If the addressed location is write
protected by the WC pin, the memory replies with
a NoAck, and the location is not modified. If, in-
stead, the WC pin has been held at 0, as shown in
Figure 6, the memory replies with an Ack. The
master terminates the transfer by generating a
STOP condition.
Page Write
The Page Write mode allows up to 64 bytes to be
written in a single write cycle, provided that they
are all located in the same 'row' in the memory:

Table 3. Device Select Code

Note: 1. The most significant bit, b7, is sent first.

Device Type Identifier

Chip Enable

Device Select Code

Table 4. Most Significant Byte

Note: 1. b15 is treated as Don't Care on the M24256-B series.

b15 and b14 are Don't Care on the M24128-B series.

Table 5. Least Significant Byte

b15

b14

b13

b12

b11

b10

Table 6. Operating Modes

Note: 1. X =

or V

Mode

RW bit

Data Bytes

Initial Sequence

Current Address Read

START, Device Select, RW = `1'

Random Address Read

START, Device Select, RW = `0', Address

reSTART, Device Select, RW = `1'

Sequential Read

Similar to Current or Random Address Read

Byte Write

START, Device Select, RW = `0'

Page Write

START, Device Select, RW = `0'

M24256-B, M24128-B

6/19

Figure 5. Write Mode Sequences with WC=1 (data write inhibited)

STOP

START

BYTE WRITE

DEV SEL

BYTE ADDR

DATA IN

START

PAGE WRITE

DEV SEL

BYTE ADDR

DATA IN 1

DATA IN 2

AI01120B

PAGE WRITE
(cont'd)

WC (cont'd)

STOP

DATA IN N

ACK

NO ACK

R/W

ACK

NO ACK

R/W

NO ACK

that is the most significant memory address bits
(b14-b6 for the M24256-B and b13-b6 for the
M24128-B) are the same. If more bytes are sent
than will fit up to the end of the row, a condition
known as `roll-over' occurs. Data starts to become
overwritten (in a way not formally specified in this
data sheet).
The master sends from one up to 64 bytes of data,
each of which is acknowledged by the memory if
the WC pin is low. If the WC pin is high, the con-
tents of the addressed memory location are not
modified, and each data byte is followed by a
NoAck. After each byte is transferred, the internal
byte address counter (the 6 least significant bits
only) is incremented. The transfer is terminated by
the master generating a STOP condition.
When the master generates a STOP condition im-
mediately after the Ack bit (in the "10

bit" time

slot), either at the end of a byte write or a page
write, the internal memory write cycle is triggered.

A STOP condition at any other time does not trig-
ger the internal write cycle.
During the internal write cycle, the SDA input is
disabled internally, and the device does not re-
spond to any requests.

7/19

M24256-B, M24128-B

Figure 6. Write Mode Sequences with WC=0 (data write enabled)

STOP

START

BYTE WRITE

DEV SEL

BYTE ADDR

DATA IN

START

PAGE WRITE

DEV SEL

BYTE ADDR

DATA IN 1

DATA IN 2

AI01106B

PAGE WRITE
(cont'd)

WC (cont'd)

STOP

DATA IN N

ACK

R/W

ACK

R/W

ACK

Minimizing System Delays by Polling On ACK
During the internal write cycle, the memory discon-
nects itself from the bus, and copies the data from
its internal latches to the memory cells. The maxi-
mum write time (t

) is shown in Table 9, but the

typical time is shorter. To make use of this, an Ack
polling sequence can be used by the master.
The sequence, as shown in Figure 7, is:
Initial condition: a Write is in progress.
Step 1: the master issues a START condition

followed by a Device Select Code (the first byte
of the new instruction).

Step 2: if the memory is busy with the internal

write cycle, no Ack will be returned and the mas-
ter goes back to Step 1. If the memory has ter-
minated the internal write cycle, it responds with
an Ack, indicating that the memory is ready to
receive the second part of the next instruction
(the first byte of this instruction having been sent
during Step 1).

Read Operations
Read operations are performed independently of
the state of the WC pin.
Random Address Read
A dummy write is performed to load the address
into the address counter, as shown in Figure 8.
Then,

without sending a STOP condition, the mas-

ter sends another START condition, and repeats
the Device Select Code, with the RW bit set to `1'.
The memory acknowledges this, and outputs the
contents of the addressed byte. The master must
not acknowledge the byte output, and terminates
the transfer with a STOP condition.
Current Address Read
The device has an internal address counter which
is incremented each time a byte is read. For the
Current Address Read mode, following a START
condition, the master sends a Device Select Code
with the RW bit set to `1'. The memory acknowl-
edges this, and outputs the byte addressed by the

M24256-B, M24128-B

8/19

Acknowledge in Read Mode
In all read modes, the memory waits, after each
byte read, for an acknowledgment during the 9

bit time. If the master does not pull the SDA line
low during this time, the memory terminates the
data transfer and switches to its stand-by state.

internal address counter. The counter is then in-
cremented. The master terminates the transfer
with a STOP condition, as shown in Figure 8,

with-

out acknowledging the byte output.
Sequential Read
This mode can be initiated with either a Current
Address Read or a Random Address Read. The
master

does acknowledge the data byte output in

this case, and the memory continues to output the
next byte in sequence. To terminate the stream of
bytes, the master must

not acknowledge the last

byte output, and

must generate a STOP condition.

The output data comes from consecutive address-
es, with the internal address counter automatically
incremented after each byte output. After the last
memory address, the address counter `rolls-over'
and the memory continues to output data from
memory address 00h.

Figure 7. Write Cycle Polling Flowchart using ACK

WRITE Cycle

in Progress

AI01847

Operation is

Addressing the

Memory

START Condition

DEVICE SELECT

with RW = 0

ACK

Returned

YES

ReSTART

STOP

Proceed

WRITE Operation

Proceed

Random Address

READ Operation

Send

Byte Address

First byte of instruction
with RW = 0 already
decoded by M24xxx

M24256-B, M24128-B

10/19

Table 7. DC Characteristics
(T

= 40 to 85

C; V

= 4.5 to 5.5 V or 2.5 to 5.5 V)

= 20 to 85

C; V

= 1.8 to 3.6 V)

Note: 1. This is preliminary data.

Table 8. Input Parameters

= 25

C, f = 400 kHz)

Note: 1. Sampled only, not 100% tested.

Symbol

Parameter

Test Condition

Min.

Max.

Unit

Input Leakage Current

(SCL, SDA)

0 V

Output Leakage Current

0 V

OUT

CC,

SDA in Hi-Z

Supply Current

=5V, f

=400kHz (rise/fall time < 30ns)

-W series:

=2.5V, f

=400kHz (rise/fall time < 30ns)

-R series:

=1.8V, f

=100kHz (rise/fall time < 30ns)

0.5

CC1

Supply Current
(Stand-by)

= V

or V

, V

= 5 V

-W series:

= V

or V

, V

= 2.5 V

-R series:

= V

or V

, V

= 1.8 V

Input Low Voltage (SCL, SDA)

0.3

0.3V

Input High Voltage (SCL, SDA)

0.7V

Input Low Voltage
(E0-E2, WC)

0.3

0.5

Input High Voltage
(E0-E2, WC)

0.7V

Output Low
Voltage

= 3 mA, V

= 5 V

0.4

-W series:

= 2.1 mA, V

= 2.5 V

0.4

-R series:

= 0.7 mA, V

= 1.8 V

0.2

Symbol

Parameter

Test Condition

Min.

Max.

Unit

Input Capacitance (SDA)

Input Capacitance (other pins)

Input Impedance (E0-E2, WC)

0.5 V

Input Impedance (E0-E2, WC)

0.7V

500

Pulse width ignored
(Input Filter on SCL and SDA)

Single glitch

100

11/19

M24256-B, M24128-B

Table 9. AC Characteristics

Note: 1. For a reSTART condition, or following a write cycle.

2. Sampled only, not 100% tested.
3. To avoid spurious STAR T and STOP conditions, a minimum delay is placed between SCL=1 and the falling or rising edge of SDA.
4. This is preliminary data.

Symbol

Alt.

Parameter

M24256-B / M24128-B

Unit

=4.5 to 5.5 V

=40 to 85

=2.5 to 5.5 V

=40 to 85

=1.8 to 3.6 V

=20 to 85

Min

Max

Min

Max

Min

Max

CH1CH2

Clock Rise Time

300

CL1CL2

Clock Fall Time

300

DH1DH2

SDA Rise Time

300

DL1DL2

SDA Fall Time

300

CHDX

SU:STA

Clock High to Input Transition

600

CHCL

HIGH

Clock Pulse Width High

600

DLCL

HD:STA

Input Low to Clock Low (START)

600

CLDX

HD:DAT

Clock Low to Input Transition

CLCH

LOW

Clock Pulse Width Low

1.3

DXCX

SU:DAT

Input Transition to Clock
Transition

100

CHDH

SU:STO

Clock High to Input High (STOP)

600

DHDL

BUF

Input High to Input Low (Bus
Free)

1.3

CLQV

Clock Low to Data Out Valid

200

900

200

900

200

900

CLQX

Data Out Hold Time After Clock
Low

200

SCL

Clock Frequency

400

kHz

Write Time

Table 10. AC Measurement Conditions

Input Rise and Fall Times

50 ns

Input Pulse Voltages

0.2V

to 0.8V

Input and Output Timing
Reference Voltages

0.3V

to 0.7V

Figure 9. AC Testing Input Output Waveforms

AI00825

0.8VCC

0.2VCC

0.7VCC

0.3VCC

13/19

M24256-B, M24128-B

Table 11. Ordering Information Scheme

Note: 1. Available only on request.

Example:

M24256

Memory Capacity

Option

256

256 Kbit (32K x 8)

Tape and Reel Packing

128

128 Kbit (16K x 8)

Temperature Range

C to 85

Operating Voltage

Package

blank

4.5 V to 5.5 V

PSDIP8 (0.25 mm frame)

2.5 V to 5.5 V

SO8 (150 mil width)

1.8 V to 3.6 V

TSSOP8 (169 mil width)

TSSOP14 (169 mil width)

ORDERING INFORMATION
Devices are shipped from the factory with the
memory content set at all `1's (FFh).
The notation used for the device number is as
shown in Table 11. For a list of available options
(speed, package, etc.) or for further information on
any aspect of this device, please contact your
nearest ST Sales Office.

19/19

M24256-B, M24128-B

Information furnished is believed to be accurate and reliable. However, STMi croelectronics assumes no responsibility for the consequences
of use of such information nor for any infringement of patents or other rights of third parties which may result from its use. No license is granted
by implication or otherwise under any patent or patent rights of STMicroelectronics. Specifications mentioned in this publication are subject
to change without notice. This publication supersedes and replaces all information previously supplied. STMicroelectronics products are not
authorized for use as criti cal components in life support devices or systems without express writt en approval of STMicroelectronics.

The ST logo is a registered trademark of STMicroelectronics.

All other names are the property of their respective owners.

STMicroelectronics GROUP OF COMPANIES

Australia - Brazil - China - Finland - France - Germany - Hong Kong - India - Italy - Japan - Malaysia - Malta - Morocco - Singapore - Spain -

Sweden - Switzerland - United Kingdom - U.S.A.

http:// www.st.com

Ð­Ð»ÐµÐºÑ‚Ñ€Ð¾Ð½Ð½Ñ‹Ð¹ ÐºÐ¾Ð¼Ð¿Ð¾Ð½ÐµÐ½Ñ‚: M24256-B

ÐÐ»ÐµÐºÑ‚Ñ€Ð¾Ð½Ð½Ñ‹Ð¹ ÐºÐ¾Ð¼Ð¿Ð¾Ð½ÐµÐ½Ñ‚: M24256-B