July 2001
1/10
Rev. 1.1
ST6200L/01L/03L
LOW VOLTAGE 8-BIT ROM MCUs WITH A/D CONVERTER,
TWO TIMERS & SAFE RESET
s
Memories
1K or 2K bytes Program memory with read-
out protection
64 bytes RAM
s
Clock, Reset and Supply Management
Enhanced reset system
Clock sources: crystal/ceramic resonator or
RC network, external clock
2 Power Saving Modes: Wait and Stop
s
Interrupt Management
4 interrupt vectors plus NMI and RESET
9 external interrupt lines (on 2 vectors)
s
9 I/O Ports
9 multifunctional bidirectional I/O lines
4 alternate function lines
3 high sink outputs (12mA)
s
2 Timers
Configurable watchdog timer
8-bit timer/counter with a 7-bit prescaler
s
Analog Peripheral
8-bit ADC with 4 input channels (except on
ST6203L)
s
Instruction Set
8-bit data manipulation
40 basic instructions
9 addressing modes
Bit manipulation
s
Development Tools
Full hardware/software development package
Device Summary
(See
Section 1.3
for Ordering Information)
PDIP16
SO16
SSOP16
Features
ST6200L
ST6201L
ST6203L
Program memory - bytes
1K
2K
1K
RAM - bytes
64
Operating Supply
2.4V to 3.9V
Analog Inputs
4
-
Clock Frequency
4MHz Max
Operating Temperature
0C to +70C
Packages
PDIP16 / SO16 / SSOP16
1
2/10
ST6200L/01L/03L
1 GENERAL DESCRIPTION
1.1 INTRODUCTION
The ST6200L/01L and 03L are low voltage mask
programmed ROM version of ST62T00C,T01C
and T03C OTP devices.
They offer the same functionality as OTP devices,
selecting as ROM options the options defined in
the programmable option byte of the OTP version,
with the exception of the LVD Reset and the OSG
that are not available.
Figure 1. Programming wave form
1.2 ROM READOUT PROTECTION
If the ROM READOUT PROTECTION option is
selected, a protection fuse can be blown to pre-
vent any access to the program memory content.
In case the user wants to blow this fuse, high volt-
age must be applied on the V
PP
pin.
Figure 2. Programming Circuit
Note: ZPD15 is used for overvoltage protection
VR02001
0.5s min
15
10
5
14V typ
100 s max
t
t
4mA typ
100mA
150 s typ
max
V
V
PP
PP
VR02003
PROTECT
ZPD15
5V
V
SS
V
DD
V
47 F
m
100nF
100nF
15V
14V
PP
1
3/10
ST6200L/01L/03L
1.3 ORDERING INFORMATION
The following section deals with the procedure for
transfer of customer codes to STMicroelectronics.
1.3.1 Transfer of Customer Code
Customer code is made up of the ROM contents
and the list of the selected mask options. The
ROM contents are to be sent on diskette, or by
electronic means, with the hexadecimal file gener-
ated by the development tool. All unused bytes
must be set to FFh.
The selected mask options are communicated to
STMicroelectronics using the correctly filled OP-
TION LIST appended. See
page 4
.
1.3.2 Listing Generation and Verification
When STMicroelectronics receives the user's
ROM contents, a computer listing is generated
from it. This listing refers exactly to the mask which
will be used to produce the specified MCU. The
listing is then returned to the customer who must
thoroughly check, complete, sign and return it to
STMicroelectronics. The signed listing forms a
part of the contractual agreement for the creation
of the specific customer mask.
The STMicroelectronics Sales Organization will be
pleased to provide detailed information on con-
tractual points.
Table 1. ROM Memory Map for ST6200L,03L
Table 2. ROM Memory Map for ST6201L
Table 3. ROM version Ordering Information
Device Address
Description
0000h-0B9Fh
0BA0h-0F9Fh
0FA0h-0FEFh
0FF0h-0FF7h
0FF8h-0FFBh
0FFCh-0FFDh
0FFEh-0FFFh
Reserved
User ROM
Reserved
Interrupt Vectors
Reserved
NMI Interrupt Vector
Reset Vector
Device Address
Description
0000h-087Fh
0880h-0F9Fh
0FA0h-0FEFh
0FF0h-0FF7h
0FF8h-0FFBh
0FFCh-0FFDh
0FFEh-0FFFh
Reserved
User ROM
Reserved
Interrupt Vectors
Reserved
NMI Interrupt Vector
Reset Vector
Sales Type
ROM
Analog inputs
Temperature Range
Package
ST6200LB1/XXX
1036 Bytes
4
0 to +70C
PDIP16
ST6200LM1/XXX
PSO16
ST6200LN1/XXX
SSOP16
ST6201LB1/XXX
1836 Bytes
PDIP16
ST6201LM1/XXX
PSO16
ST6201LN1/XXX
SSOP16
ST6203LB1/XXX
1036 Bytes
None
PDIP16
ST6203LM1/XXX
PSO16
ST6203LN1/XXX
SSOP16
1
4/10
ST6200L/01L/03L
ST6200L/01L/03L MICROCONTROLLER OPTION LIST
Customer:
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Address:
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Contact:
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Phone:
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Reference: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
STMicroelectronics references:
Device:
[ ] ST6200L (1 KB)
[ ] ST6203L (1 KB)
[ ] ST6201L (2 KB)
Package:
[ ] Dual in Line Plastic
[ ] Small Outline Plastic with conditioning
[ ] Shrink Small Outline Plastic with conditioning
Conditioning option:
[ ] Standard (Tube)
[ ] Tape & Reel
Temperature Range:
[ ] 0C to + 70C
Marking:
[ ] Standard marking
[ ] Special marking:
PDIP16 (9 char. max): _ _ _ _ _ _ _ _ _
PSO16 (6 char. max): _ _ _ _ _ _
SSOP16 (10 char. max): _ _ _ _ _ _ _ _ _ _
Authorized characters are letters, digits, '.', '-', '/' and spaces only.
Watchdog Selection:
[ ] Software Activation
[ ] Hardware Activation
NMI pull-up:
[ ] Enabled
[ ] Disabled
Oscillator Selection:
[ ] Quartz crystal / Ceramic resonator
[ ] RC network
Readout Protection:
[ ] Enabled:
[ ] Fuse is blown by STMicroelectronics
[ ] Fuse can be blown by the customer
[ ] Disabled
External STOP Mode Control:
[ ] Enabled
[ ] Disabled
Comments:
Oscillator Frequency in the application:
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Supply Operating Range in the application:
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Notes:
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Date:
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Signature:
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1
5/10
ST6200L/01L/03L
2 ELECTRICAL CHARACTERISTICS
2.1 ABSOLUTE MAXIMUM RATINGS
This product contains devices to protect the inputs
against damage due to high static voltages, how-
ever it is advisable to take normal precaution to
avoid application of any voltage higher than the
specified maximum rated voltages.
For proper operation it is recommended that V
I
and V
O
be higher than V
SS
and lower than V
DD
.
Reliability is enhanced if unused inputs are con-
nected to an appropriate logic voltage level (V
DD
or V
SS
).
Power Considerations.The average chip-junc-
tion temperature, Tj, in Celsius can be obtained
from:
Tj=TA + PD x RthJA
Where:TA = Ambient Temperature.
RthJA =Package thermal resistance (junc-
tion-to ambient).
PD = Pint + Pport.
Pint =IDD x VDD (chip internal power).
Pport =Port power dissipation (determined
by the user).
Notes:
- Stresses above those listed as "absolute maximum ratings" may cause permanent damage to the device. This is a stress rating only and
functional operation of the device at these conditions is not implied. Exposure to maximum rating conditions for extended periods may
affect device reliability.
- (1) Within these limits, clamping diodes are guarantee to be not conductive. Voltages outside these limits are authorised as long as injection
current is kept within the specification.
Symbol
Parameter
Value
Unit
V
DD
Supply Voltage
-0.3 to 7.0
V
V
I
Input Voltage
V
SS
- 0.3 to V
DD
+ 0.3
(1)
V
V
O
Output Voltage
V
SS
- 0.3 to V
DD
+ 0.3
(1)
V
I
O
Current Drain per Pin Excluding V
DD
, V
SS
10
mA
IV
DD
Total Current into V
DD
(source)
50
mA
IV
SS
Total Current out of V
SS
(sink)
50
mA
Tj
Junction Temperature
150
C
T
STG
Storage Temperature
-60 to 150
C
1
PDF 
ZIP