Supertex inc.
Supertex inc.
1235 Bordeaux Drive, Sunnyvale, CA 94089
Tel: (408) 222-8888
FAX: (408) 222-4895
www.supertex.com
1
HV835
Initial Release
Low Noise Dual EL Lamp Driver
Features
Low audible noise
Independent input control for lamp selection
160V
PP
output voltage
Split supply capability
Patented output timing
One miniature inductor to power both lamps
Low shutdown current
Wide input voltage range 2.0V to 5.8V
Output voltage regulation
No SCR output
Available in MLP/DFN-10 package
Applications
Dual display cellular phones
Keypad and LCD backlighting
Portable instrumentation
Dual segment lamps
Handheld wireless communication devices
General Description
The Supertex HV835 is a high voltage driver designed for driving
two EL lamps with a combined area of 3.5 square inches. The
input supply voltage range is from 2.0V to 5.8V. The device is
designed to reduce the amount of audible noise emitted by the
lamp. This device uses a single inductor and a minimum num-
ber of passive components to drive two EL lamps. The nominal
regulated output voltage of 80V is applied to the EL lamps.
The two EL lamps can be turned ON and OFF by the two logic
input control pins, C
1
and C
2
. The device is disabled when both
C
1
and C
2
(pins 1 and 4) are at logic low.
The HV835 has an internal oscillator, a switching MOSFET, and
two high voltage EL lamp drivers. Each driver has its own half
bridge common output (COM1 and COM2) connected to a single
pin called COM which minimizes the DC offset seen by the EL
lamp. An external resistor connected between the R
SW-OSC
pin and
the voltage supply pin, V
DD
, sets the frequency for the switching
MOSFET. The EL lamp driver frequency is set by dividing the
MOSFET switching frequency by 512. An external inductor is
connected between the L
X
and the V
DD
pins. Depending on the EL
lamp size, a 1.0 to 10.0nF, 100V capacitor is connected between
C
S
and Ground. The switching MOSFET charges the external
inductor and discharges it into the capacitor at C
S
. The voltage
at C
S
increases. Once the voltage at C
S
reaches a nominal value
of 80V, the switching MOSFET is turned OFF to conserve power.
Typical Application Circuit
HV835K7-G
D
+
-
+
-
1.0F
1
2
3
4
5
6
7
8
9
10
V
DD
Com
GND
EL
2
L
X
C
S
EL
1
C
1
C
2
R
SW-OSC
1.5V
0
1.5V
0
V
DD
V
IN
C
IN
4.7F
C
DD
0.1F
845k
3.3M
3.3M
EL Lamp 1
EL Lamp 2
1.0F
L
X
330
H
C
S
3.3nF, 100V
2
HV835
Ordering Information
Device
Package Options
MLP/DFN-10 (K7)
HV835
HV835K7-G
-G indicates package is RoHS compliant (`Green')
Absolute Maximum Ratings
Symbol
Parameter
Min
Typ
Max
Units
Conditions
Electrical Characteristics
(Over recommended operating conditions unless otherwise specifi ed: V
IN
= V
DD
= 3.3V, T
A
=25C)
Absolute Maximum Ratings are those values beyond which damage to the device may
occur. Functional operation under these conditions is not implied. Continuous operation
of the device at the absolute rating level may affect device reliability. All voltages are
referenced to device ground.
Parameter
Value
Supply Voltage, V
DD
-0.5V to 7.5V
Output Voltage, V
CS
-0.5V to 120V
Operating Temperature Range
-40C to 85C
Storage temperature
-65C to 150C
Symbol
Parameter
Min
Typ
Max
Units
Conditions
Recommended Operating Conditions
V
DD
Supply voltage
2.0
-
5.8
V
---
T
A
Operating temperature
-40
-
+85
o
C
---
Pin Confi guration
Thermal Resistance
Package
ja
MLP/DFN-10
60
o
C/W
Note: Mounted on FR4 board, 25mm x 25mm x 1.57mm
R
DS(ON)
On-resistance of switching
transistor
-
-
10
I = 100mA
V
DD
Input voltage range
2.0
-
5.8
V
---
V
CS
Output regulation voltage
72
80
88
V
V
DD
= 2.0V to 5.8V
V
DIFF
Differential output peak to peak
voltage (EL
1
to COM, EL
2
to COM)
144
160
176
V
V
DD
= 2.0V to 5.8V
I
DDQ
Quiescent V
DD
supply current
-
-
150
nA
C
1
= C
2
= 0.1V
-
-
250
nA
C
1
= C
2
= 0.3V
I
DD
Input current into the V
DD
pin
-
-
200
A
V
DD
= 5.8V
I
IN
Average input current including
inductor current when driving both
lamps
-
16
25
mA
V
IN
= 5.5V (See Figure 1)
V
CS
Output voltage on V
CS
when driving
both lamps
-
80
-
V
V
IN
= 5.5V (See Figure 1)
HV835K7-G
Top View
C
1
V
DD
R
SW-OSC
C
2
GND
EL
1
EL
2
COM
C
S
L
X
Pin 1
Note: Pads are on the bottom of the package.
Back-side heat slug is at ground potential.
3
HV835
Functional Block Diagram
V
DIF
Differential output peak to peak volt-
age across each lamp (EL
1
to COM,
EL
2
to COM)
-
160
-
V
V
IN
= 5.5V (See Figure 1)
f
EL
V
DIFF
output drive frequency
170
200
230
Hz
R
SW
= 845k
f
SW
Switching transistor frequency
87
102
118
kHz
R
SW
= 845k
f
SW temp
Switching transistor frequency
tempco
-
15
-
%
T
A
= -40C to +85C
D
Switching transistor duty cycle
-
85
-
%
T
A
= -40C to +85C
I
IL
Input logic low current
-
-
1.0
A
V
DD
= 2.0V to 5.8V
I
IH
Input logic low current
-
-
1.0
A
V
DD
= 2.0V to 5.8V
V
IL
Logic input low voltage
0
-
0.3
V
---
V
IH
Logic input high voltage
1.5
-
V
DD
V
---
Symbol
Parameter
Min
Typ
Max
Units
Conditions
Electrical Characteristics (cont.)
V
CS
Output
Drivers
V
SENSE
-
+
V
REF
Control logic
and switch
oscillator
Disable
Logic control and
divide by 512
EL
1
EL
2
R
SW-OSC
C
S
L
X
V
DD
C
1
C
2
GND
COM1
C
COM
COM2
V
DD
V
CS
V
CS
Function Table
Logic Inputs
Outputs
Device
C
1
C
2
EL
1
EL
2
COM
0
0
Hi Z
Hi Z
Hi Z
OFF
0
1
Hi Z
ON
ON
ON
1
0
ON
Hi Z
ON
ON
1
1
ON
ON
ON
ON
4
HV835
Figure 1 - Test Circuit
+
-
+
-
1
2
3
4
5
6
7
8
9
10
* or any (equivalent or better) > 90V, fast recovery diode
** Cooper LPO6610-334MLB
*** The bigger sized lamp should be tied to EL1 and the smaller
sized lamp to EL2 (pins 10 and 9 respectively)
V
DD
Com
C
2
GND
EL
2
L
X
C
S
EL
1
C
1
R
SW-OSC
HV835K7-G
2.1in
2
EL Lamp 1***
1.8in
2
EL Lamp 2***
620
13nF
620
11nF
1N4148*
C
S
3.3nF, 100V
L
X
330H**
845k
C
DD
0.1F
C
IN
4.7F
V
IH
= ON
0 = OFF
V
IH
= ON
0 = OFF
V
DD
V
IN
Lamp
V
DD
V
IN
I
IN
V
CS
f
EL
Lamp Brightness
EL
1
EL
2
EL
1
ON
3.0V
5.2V
6.15mA
80V
peak
200Hz
13.26 cd/m
2
---
EL
2
ON
5.08mA
---
13.12 cd/m
2
Both EL
1
and EL
2
ON
9.10mA
12.72 cd/m
2
12.23 cd/m
2
EL
1
ON
5.5V
5.7mA
13.34 cd/m
2
---
EL
2
ON
4.76mA
---
13.24 cd/m
2
Both EL
1
and EL
2
ON
8.52mA
12.84 cd/m
2
12.43 cd/m
2
EL
1
ON
5.8V
5.45mA
13.42 cd/m
2
---
EL
2
ON
4.41mA
---
13.30 cd/m
2
Both EL
1
and EL
2
ON
7.94mA
13.00 cd/m
2
12.55 cd/m
2
Typical Performance
5
HV835
Pin Confi guration and Description
Pin #
Function
Description
1
C
1
Enable input signal for EL Lamp 1. Logic high will turn ON the EL lamp 1 and logic low will turn it OFF.
Refer to the function table.
2
V
DD
Input voltage supply pin.
3
R
SW-OSC
External resistor connection to set both the switching MOSFET frequency and EL Lamp frequency. The
external resistor should be connected between V
DD
and this pin. The EL lamp frequency is the switch-
ing frequency divided by 512. The switching frequency is inversely proportional to the resistor value.
A 845k resistor will provide a nominal switching frequency of 102kHz and an EL lamp frequency of
200Hz. To change the frequency to f
EL1
, the value of the resistor R
SW-OSC1
can be determined as R
SW-OSC1
= (845 x 200) / f
EL1
k.
4
C
2
Enable input signal for EL Lamp 2. Logic high will turn ON the EL lamp 2 and logic low will turn it OFF.
Refer to the function table.
5
GND
Device ground.
6
L
X
Drain of internal switching MOSFET. Connection for an external inductor. When the switching MOSFET
is turned ON, the inductor is being charged. When the MOSFET is turned OFF, the energy stored in the
inductor is transferred to the high voltage capacitor connected at the C
S
pin.
7
C
S
Connect a 100V capacitor between this pin and GND. This capacitor stores the energy transferred from
the inductor.
8
COM
Common lamp connection for both EL
1
and EL
2
. Connect one end of both the lamps to this pin.
9
EL
2
EL lamp 2 connection. For optimum performance, the smaller of the two lamps should be connected
to this pin.
10
EL
1
EL lamp 1 connection. For optimum performance, the larger of the two lamps should be connected to
this pin.
Figure 2 - Split Supply Confi guration
HV835K7-G
D
C
S
L
X
C
IN
C
DD
1
2
3
4
5
6
7
8
9
10
V
DD
Com
GND
EL
2
L
X
C
S
EL
1
C
1
C
2
R
SW-OSC
V
EN
= ON
0 = OFF
V
EN
= ON
0 = OFF
Regulated Voltage = V
DD
Battery Voltage = V
IN
R
SW-OSC
EL Lamp 1
EL Lamp 2
Split Supply Confi guration
The HV835 can be used in applications operating from a
battery where a regulated voltage is available. This is shown
in Figure 2. The regulated voltage can be used to drive the
internal logic of HV835. The amount of current used to drive
the internal logic is less than 200A. Therefore, the regu-
lated voltage could easily provide the current without being
loaded down.
Supertex inc.
1235 Bordeaux Drive, Sunnyvale, CA 94089
TEL: (408) 222-8888 / FAX: (408) 222-4895
www.supertex.com
2006 Supertex inc. All rights reserved. Unauthorized use or reproduction is prohibited.
Supertex inc.
does not recommend the use of its products in life support applications, and will not knowingly sell its products for use in such applications, unless it receives an adequate
"product liability indemnification insurance agreement". Supertex does not assume responsibility for use of devices described and limits its liability to the replacement of the devices
determined defective due to workmanship. No responsibility is assumed for possible omissions or inaccuracies. Circuitry and specifications are subject to change without notice. For the latest
product specifications, refer to the Supertex website: http//www.supertex.com.
6
Doc.# DSFP - HV835
NR051806
HV835
(The package drawing(s) in this data sheet may not refl ect the most current specifi cations. For the latest package outline
information go to
http://www.supertex.com/packaging.html
.)
10-Lead DFN/MLP (3x3) Package (K7)
Top View
Side View
0.30
+0.15
-0.10
1.60
3.00
All dimensions are in millimeters
0.50
Pin #1 Index
3.00
2.20
0.20
0.25
+0.05
-0.07
0.7 - 0.8
0.0 - 0.05
PDF 
ZIP