18-Bit Registered Transceivers
CY74FCT16501T
CY74FCT162501T
CY74FCT162H501T
SCCS057 - August 1994 - Revised March 2000
Data sheet acquired from Cypress Semiconductor Corporation.
Data sheet modified to remove devices not offered.
Copyright
2000, Texas Instruments Incorporated
1CY74FCT162H501
T
Features
FCT-E speed at 3.8 ns
Power-off disable outputs permits live insertion
Edge-rate control circuitry for significantly improved
noise characteristics
Typical output skew < 250 ps
ESD > 2000V
TSSOP (19.6 mil pitch) and SSOP (25-mil pitch)
packages
Industrial temperature range of
-
40C to +85C
V
CC
= 5V
10%
CY74FCT16501T Features:
64 mA sink current, 32 mA source current
Typical V
OLP
(ground bounce) <1.0V at V
CC
= 5V,
T
A
= 25C
CY74FCT162501T Features:
Balanced 24 mA output drivers
Reduced system switching noise
Typical V
OLP
(ground bounce) <0.6V at V
CC
= 5V,
T
A
= 25C
CY74FCT162H501T Features:
Bus hold retains last active state
Eliminates the need for external pull-up or pull-down
resistors
Functional Description
These 18-bit universal bus transceivers can be operated in
transparent, latched or clock modes by combining D-type
latches and D-type flip-flops. Data flow in each direction is
controlled by output enable (OEAB and OEBA), latch enable
(LEAB and LEBA), and clock inputs (CLKAB and CLKBA). For
A-to-B data flow, the device operates in transparent mode
when LEAB is HIGH. When LEAB is LOW, the A data is latched
if CLKAB is held at a HIGH or LOW logic level. If LEAB is LOW,
the A bus data is stored in the latch/flip-flop on the
LOW-to-HIGH transition of CLKAB. OEAB performs the output
enable function on the B port. Data flow from B-to-A is similar
to that of A-to-B and is controlled by OEBA, LEBA, and CLKBA.
The output buffers are designed with a power-off disable
feature to allow live insertion of boards.
The
CY74FCT16501T
is
ideally
suited
for
driving
high-capacitance loads and low-impedance backplanes.
THE CY74FCT162501T has 24-mA balanced output drivers
with current limiting resistors in the outputs. This reduces the
need for external terminating resistors and provides for minimal
undershoot
and
reduced
ground
bounce.
The
CY74FCT162501T is ideal for driving transmission lines.
The CY74FCT162H501T is a 24-mA balanced output part, that
has "bus hold" on the data inputs. The device retains the input's
last state whenever the input goes to high impedance. This
eliminates the need for pull-up/down resistors and prevents
floating inputs.
GND
Functional Block Diagram
Pin Configuration
1
2
3
4
5
6
7
8
9
10
11
12
OEAB
SSOP/TSSOP
Top View
13
14
15
16
17
18
19
20
21
22
23
24
LEAB
A
1
GND
GND
V
CC
GND
GND
FCT16501-1
A
2
A
3
A
4
A
5
A
6
A
7
A
8
A
9
GND
25
26
27
28
GND
A
10
A
11
A
12
V
CC
A
13
A
14
A
15
A
16
A
17
A
18
OEBA
LEBA
56
55
54
53
52
51
50
49
48
47
46
45
44
43
42
41
40
39
38
37
36
35
34
33
32
31
30
29
GND
CLKAB
B
1
GND
B
2
B
3
V
CC
B
4
B
5
B
6
GND
B
7
B
8
B
9
B
10
B
11
B
12
B
13
B
14
B
15
V
CC
B
16
B
17
B
18
CLKBA
OEAB
CLKBA
LEBA
OEBA
CLKAB
LEAB
C
D
C
D
C
D
A
1
B
1
C
D
TO 17 OTHER CHANNELS
FCT16501-2
CY74FCT16501T
CY74FCT162501T
CY74FCT162H501T
2
Maximum Ratings
[6, 7]
(Above which the useful life may be impaired. For user
guidelines, not tested.)
Storage Temperature
.................................... -
55
C to +125
C
Ambient Temperature with
Power Applied
.................................................. -
55
C to +125
C
DC Input Voltage
................................................. -
0.5V to +7.0V
DC Output Voltage
.............................................. -
0.5V to +7.0V
DC Output Current
(Maximum Sink Current/Pin)
........................... -
60 to +120 mA
Power Dissipation.......................................................... 1.0W
Static Discharge Voltage ........................................... >2001V
(per MIL-STD-883, Method 3015)
Notes:
1.
On the 74FCT162H501T these pins have bus hold.
2.
A-to-B data flow is shown. B-to-A data flow is similar but uses OEBA, LEBA, and CLKBA.
3.
H = HIGH Voltage Level
L = LOW Voltage Level
X = Don't Care
Z = High-impedance
= LOW-to-HIGH Transition
4.
Output level before the indicated steady-state input conditions were established.
5.
Output level before the indicated steady-state input conditions were established, provided that CLKAB was HIGH before LEAB went LOW.
6.
Operation beyond the limits set forth may impair the useful life of the device. Unless otherwise noted, these limits are over the operating free-air temperature range.
7.
Unused inputs must always be connected to an appropriate logic voltage level, preferably either V
CC
or ground.
Pin Description
Name
Description
OEAB
A-to-B Output Enable Input
OEBA
B-to-A Output Enable Input (Active LOW)
LEAB
A-to-B Latch Enable Input
LEBA
B-to-A Latch Enable Input
CLKAB
A-to-B Clock Input
CLKBA
B-to-A Clock Input
A
A-to-B Data Inputs or B-to-A Three-State
Outputs
[1]
B
B-to-A Data Inputs or A-to-B Three-State
Outputs
[1]
Function Table
[2, 3]
Inputs
Outputs
OEAB
LEAB
CLKAB
A
B
L
X
X
X
Z
H
H
X
L
L
H
H
X
H
H
H
L
L
L
H
L
H
H
H
L
L
X
B
[4]
H
L
H
X
B
[5]
Operating Range
Range
Ambient
Temperature
V
CC
Industrial
-
40
C to +85
C
5V
10%
CY74FCT16501T
CY74FCT162501T
CY74FCT162H501T
3
Electrical Characteristics
Over the Operating Range
Parameter
Description
Test Conditions
Min.
Typ.
[8]
Max.
Unit
V
IH
Input HIGH Voltage
2.0
V
V
IL
Input LOW Voltage
0.8
V
V
H
Input Hysteresis
[9]
100
mV
V
IK
Input Clamp Diode Voltage
V
CC
=Min., I
IN
=
-
18 mA
-
0.7
-
1.2
V
I
IH
Input HIGH Current
Standard
V
CC
=Max., V
I
=V
CC
1
A
Bus Hold
100
I
IL
Input LOW Current
Standard
V
CC
=Max., V
I
=GND
1
A
Bus Hold
100
A
I
BBH
I
BBL
Bus Hold Sustain Current on Bus Hold Input
[10]
V
CC
=Min.,
V
I
=2.0V
-
50
A
V
I
=0.8V
+50
A
I
BHHO
I
BHLO
Bus Hold Overdrive Current on Bus Hold In-
put
[10]
V
CC
=Max., V
I
=1.5V
TBD
mA
I
OZH
High Impedance Output Current
(Three-State Output pins)
V
CC
=Max., V
OUT
=2.7V
1
A
I
OZL
High Impedance Output Current
(Three-State Output pins)
V
CC
=Max., V
OUT
=0.5V
1
A
I
OS
Short Circuit Current
[11]
V
CC
=Max., V
OUT
=GND
-
80
-
140
-
200
mA
I
O
Output Drive Current
[11]
V
CC
=Max., V
OUT
=2.5V
-
50
-
180
mA
I
OFF
Power-Off Disable
V
CC
=0V, V
OUT
4.5V
[12]
1
A
Output Drive Characteristics for CY74FCT16501T
Parameter
Description
Test Conditions
Min.
Typ.
[8]
Max.
Unit
V
OH
Output HIGH Voltage
V
CC
=Min., I
OH
=
-
3 mA
2.5
3.5
V
V
CC
=Min., I
OH
=
-
15 mA
2.4
3.5
V
CC
=Min., I
OH
=
-
32 mA
2.0
3.0
V
OL
Output LOW Voltage
V
CC
=Min., I
OL
=64 mA
0.2
0.55
V
Output Drive Characteristics for CY74FCT162501T, CY74FCT162H501T
Parameter
Description
Test Conditions
Min.
Typ.
[8]
Max.
Unit
I
ODL
Output LOW Current
[11]
V
CC
=5V, V
IN
=V
IH
or V
IL
, V
OUT
=1.5V
60
115
150
mA
I
ODH
Output HIGH Current
[11]
V
CC
=5V, V
IN
=V
IH
or V
IL
, V
OUT
=1.5V
-
60
-
115
-
150
mA
V
OH
Output HIGH Voltage
V
CC
=Min., I
OH
=
-
24 mA
2.4
3.3
V
V
OL
Output LOW Voltage
V
CC
=Min., I
OL
=24 mA
0.3
0.55
V
Notes:
8.
Typical values are at V
CC
= 5.0V, T
A
= +25C ambient.
9.
This parameter is specified but not tested.
10. Pins with bus hold are described in Pin Description.
11. Not more than one output should be shorted at a time. Duration of short should not exceed one second. The use of high-speed test apparatus and/or sample
and hold techniques are preferable in order to minimize internal chip heating and more accurately reflect operational values. Otherwise prolonged shorting of
a high output may raise the chip temperature well above normal and thereby cause invalid readings in other parametric tests. In any sequence of parameter
tests, I
OS
tests should be performed last.
12. Tested at +25C.
CY74FCT16501T
CY74FCT162501T
CY74FCT162H501T
4
Capacitance
[9]
(T
A
= +25C, f = 1.0 MHz)
Parameter
Description
Test Conditions
Typ.
[8]
Max.
Unit
C
IN
Input Capacitance
V
IN
= 0V
4.5
6.0
pF
C
OUT
Output Capacitance
V
OUT
= 0V
5.5
8.0
pF
Power Supply Characteristics
Sym.
Parameter
Test Conditions
[13]
Min.
Typ.
[8]
Max.
Unit
I
CC
Quiescent Power Supply
Current
V
CC
=Max.
V
IN
<0.2V
V
IN
>V
CC
-
0.2V
--
5
500
A
I
CC
Quiescent Power Supply
Current TTL inputs HIGH
V
CC
= Max., V
IN =
3.4V
[14]
--
0.5
1.5
mA
I
CCD
Dynamic Power Supply
Current
[15]
V
CC
=Max., Outputs Open
OEAB=OEBA=V
CC
or GND
One Input Toggling,
50% Duty Cycle
V
IN
=V
CC
or
V
IN
=GND
--
75
120
A/
MHz
I
C
Total Power Supply
Current
[16]
V
CC
=Max., Outputs Open
f
0
=10MHz (CLKAB)
50% Duty Cycle
OEAB=OEBA=V
CC
LEAB = GND, One Bit Toggling
f
1
= 5MHz, 50% Duty Cycle
V
IN
=V
CC
or
V
IN
=GND
--
0.8
1.7
mA
V
IN
=3.4V or
V
IN
=GND
--
1.3
3.2
V
CC
=Max., Outputs Open
f
0
= 10MHz (CLKAB)
50% Duty Cycle
OEAB=OEBA=V
CC
LEAB=GND
Eighteen Bits Toggling
f
1
=2.5MHz, 50% Duty Cycle
V
IN
=V
CC
or
V
IN
=GND
--
3.8
6.5
[17]
V
IN
=3.4V or
V
IN
=GND
--
8.5
20.8
[17]
Notes:
13. For conditions shown as Max. or Min., use appropriate value specified under Electrical Characteristics for the applicable device type.
14. Per TTL driven input (V
IN
=3.4V); all other inputs at V
CC
or GND.
15. This parameter is not directly testable, but is derived for use in Total Power Supply.
16. I
C
=
I
QUIESCENT
+ I
INPUTS
+ I
DYNAMIC
I
C
=
I
CC
+
I
CC
D
H
N
T
+I
CCD
(f
0
/2 + f
1
N
1
)
I
CC
=
Quiescent Current with CMOS input levels
I
CC
=
Power Supply Current for a TTL HIGH input (V
IN
=3.4V)
D
H
=
Duty Cycle for TTL inputs HIGH
N
T
=
Number of TTL inputs at D
H
I
CCD
=
Dynamic Current caused by an input transition pair (HLH or LHL)
f
0
=
Clock frequency for registered devices, otherwise zero
f
1
=
Input signal frequency
N
1
=
Number of inputs changing at f
1
All currents are in milliamps and all frequencies are in megahertz.
17. Values for these conditions are examples of the I
CC
formula. These limits are specified but not tested.
CY74FCT16501T
CY74FCT162501T
CY74FCT162H501T
5
Switching Characteristics
Over the Operating Range
[18]
CY74FCT16501AT
CY74FCT162501AT
CY74FCT162501CT
CY74FCT162H501CT
CY74FCT16501ET
CY74FCT162501ET
CY74FCT162H501ET
Fig.
No.
[19]
Parameter
Description
Min.
Max.
Min.
Max.
Min.
Max.
Unit
f
MAX
CLKAB or CLKBA
frequency
[20]
--
150
--
150
--
150
MHz
--
t
PLH
t
PHL
Propagation Delay
A to B or B to A
1.5
5.1
1.5
4.6
1.5
3.8
ns
1,3
t
PLH
t
PHL
Propagation Delay
LEBA to A, LEAB to B
1.5
5.6
1.5
5.3
1.5
4.2
ns
1,5
t
PLH
t
PHL
Propagation Delay
CLKBA to A,
CLKAB to B
1.5
5.6
1.5
5.3
1.5
4.2
ns
1,5
t
PZH
t
PZL
Output Enable Time
OEBA to A, OEAB to B
1.5
6.0
1.5
5.6
1.5
4.8
ns
1,7,8
t
PHZ
t
PLZ
Output Disable Time
OEBA to A, OEAB to B
1.5
5.6
1.5
5.2
1.5
5.2
ns
1,7,8
t
SU
Set-Up Time,
HIGH or LOW
A to CLKAB,
B to CLKBA
3.0
--
3.0
--
2.4
--
ns
4
t
H
Hold Time
HIGH or LOW
A to CLKAB,
B to CLKBA
0
--
0
--
0
--
ns
4
t
SU
Set-Up Time,
HIGH or LOW
A to LEAB,
B to LEBA
Clock
LOW
3.0
--
3.0
--
2.0
--
ns
4
Clock
HIGH
1.5
--
1.5
--
1.5
--
ns
4
t
H
Hold Time, HIGH or
LOW, A to LEAB,
B to LEBA
1.5
--
1.5
--
0.5
--
ns
4
t
W
LEAB or LEBA Pulse
Width HIGH
[20]
3.0
--
3.0
--
3.0
--
ns
5
t
W
CLKAB or CLKBA
Pulse Width HIGH or
LOW
[20]
3.0
--
3.0
--
3.0
--
ns
5
t
SK(O)
Output Skew
[21]
--
0.5
--
0.5
--
0.5
ns
--
Notes:
18. Minimum limits are specified, but not tested, on propagation delays.
19. See "Parameter Measurement Information" in the General Information section.
20. This parameter is guaranteed but not tested.
21. Skew between any two outputs of the same package switching in the same direction. This parameter ensured by design.
CY74FCT16501T
CY74FCT162501T
CY74FCT162H501T
6
Ordering Information CY74FCT16501T
Speed
(ns)
Ordering Code
Package
Name
Package Type
Operating
Range
3.8
CY74FCT16501ETPACT
Z56
56-Lead (240-Mil) TSSOP
Industrial
CY74FCT16501ETPVC/PVCT
O56
56-Lead (300-Mil) SSOP
5.1
CY74FCT16501ATPVC/PVCT
O56
56-Lead (300-Mil) SSOP
Industrial
Ordering Information CY74FCT162501T
Speed
(ns)
Ordering Code
Package
Name
Package Type
Operating
Range
3.8
74FCT162501ETPACT
Z56
56-Lead (240-Mil) TSSOP
Industrial
CY74FCT162501ETPVC
O56
56-Lead (300-Mil) SSOP
74FCT162501ETPVCT
O56
56-Lead (300-Mil) SSOP
4.6
74FCT162501CTPACT
Z56
56-Lead (240-Mil) TSSOP
Industrial
CY74FCT162501CTPVC
O56
56-Lead (300-Mil) SSOP
74FCT162501CTPVCT
O56
56-Lead (300-Mil) SSOP
5.1
74FCT162501ATPACT
Z56
56-Lead (240-Mil) TSSOP
Industrial
CY74FCT162501ATPVC
O56
56-Lead (300-Mil) SSOP
74FCT162501ATPVCT
O56
56-Lead (300-Mil) SSOP
Ordering Information CY74FCT162H501T
Speed
(ns)
Ordering Code
Package
Name
Package Type
Operating
Range
3.8
74FCT162H501ETPACT
Z56
56-Lead (240-Mil) TSSOP
Industrial
74FCT162H501ETPVC/PVCT
O56
56-Lead (300-Mil) SSOP
4.6
74FCT162H501CTPACT
Z56
56-Lead (240-Mil) TSSOP
Industrial
74FCT162H501CTPVC/PVCT
O56
56-Lead (300-Mil) SSOP
CY74FCT16501T
CY74FCT162501T
CY74FCT162H501T
7
Package Diagrams
56-Lead Shrunk Small Outline Package O56
56-Lead Thin Shrunk Small Outline Package Z56
IMPORTANT NOTICE
Texas Instruments and its subsidiaries (TI) reserve the right to make changes to their products or to discontinue
any product or service without notice, and advise customers to obtain the latest version of relevant information
to verify, before placing orders, that information being relied on is current and complete. All products are sold
subject to the terms and conditions of sale supplied at the time of order acknowledgement, including those
pertaining to warranty, patent infringement, and limitation of liability.
TI warrants performance of its semiconductor products to the specifications applicable at the time of sale in
accordance with TI's standard warranty. Testing and other quality control techniques are utilized to the extent
TI deems necessary to support this warranty. Specific testing of all parameters of each device is not necessarily
performed, except those mandated by government requirements.
CERTAIN APPLICATIONS USING SEMICONDUCTOR PRODUCTS MAY INVOLVE POTENTIAL RISKS OF
DEATH, PERSONAL INJURY, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE ("CRITICAL
APPLICATIONS"). TI SEMICONDUCTOR PRODUCTS ARE NOT DESIGNED, AUTHORIZED, OR
WARRANTED TO BE SUITABLE FOR USE IN LIFE-SUPPORT DEVICES OR SYSTEMS OR OTHER
CRITICAL APPLICATIONS. INCLUSION OF TI PRODUCTS IN SUCH APPLICATIONS IS UNDERSTOOD TO
BE FULLY AT THE CUSTOMER'S RISK.
In order to minimize risks associated with the customer's applications, adequate design and operating
safeguards must be provided by the customer to minimize inherent or procedural hazards.
TI assumes no liability for applications assistance or customer product design. TI does not warrant or represent
that any license, either express or implied, is granted under any patent right, copyright, mask work right, or other
intellectual property right of TI covering or relating to any combination, machine, or process in which such
semiconductor products or services might be or are used. TI's publication of information regarding any third
party's products or services does not constitute TI's approval, warranty or endorsement thereof.
Copyright
2000, Texas Instruments Incorporated
PDF 
ZIP