ChipFind - документация

Электронный компонент: SN54ABT16245

Скачать:  PDF   ZIP

Document Outline

www.ti.com
FEATURES
SN54ABT16245A . . . WD PACKAGE
SN74ABT16245A . . . DGG, DGV, OR DL PACKAGE
(TOP VIEW)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
48
47
46
45
44
43
42
41
40
39
38
37
36
35
34
33
32
31
30
29
28
27
26
25
1DIR
1B1
1B2
GND
1B3
1B4
V
CC
1B5
1B6
GND
1B7
1B8
2B1
2B2
GND
2B3
2B4
V
CC
2B5
2B6
GND
2B7
2B8
2DIR
1OE
1A1
1A2
GND
1A3
1A4
V
CC
1A5
1A6
GND
1A7
1A8
2A1
2A2
GND
2A3
2A4
V
CC
2A5
2A6
GND
2A7
2A8
2OE
DESCRIPTION
SN54ABT16245A, SN74ABT16245A
16-BIT BUS TRANSCEIVERS
WITH 3-STATE OUTPUTS
SCBS300F MARCH 1994 REVISED JULY 2005
Members of the Texas Instruments
WidebusTM Family
State-of-the-Art EPIC-IIBTM BiCMOS Design
Significantly Reduces Power Dissipation
Typical V
OLP
(Output Ground Bounce) <1 V at
V
CC
= 5 V, T
A
= 25
C
High-Impedance State During Power Up and
Power Down
Distributed V
CC
and GND Pin Configuration
Minimizes High-Speed Switching Noise
Flow-Through Architecture Optimizes PCB
Layout
High-Drive Outputs (32-mA I
OH
, 64-mA I
OL
)
Latch-Up Performance Exceeds 500 mA Per
JESD 70
ESD Protection Exceeds 2000 V Per
MIL-STD-883, Method 3015; Exceeds 200 V
Using Machine Model (C = 200 pF, R = 0)
Package Options Includes Plastic Thin Very
Small-Outline (DGV), Shrink Small-Outline
(DL), and Thin Shrink Small-Outline (DGG)
Packages and 380-mil Fine-Pitch Ceramic
(WD) Flat Package Using 25-mil
Center-to-Center Spacings
The 'ABT16245A devices are 16-bit noninverting 3-state transceivers designed for synchronous two-way
communication
between
data
buses.
The
control-function
implementation
minimizes
external
timing
requirements.
These devices can be used as two 8-bit transceviers or one 16-bit transceiver. They allow data transmission from
the A bus to the B bus or from the B bus to the A bus, depending on the logic level at the direction-control (DIR)
input. The output-enable (OE) input can be used to disable the device so that the buses are effectively isolated.
When V
CC
is between 0 and 2.1 V, the device is in the high-impedance state during power up or power down.
However, to ensure the high-impendance state above 2.1 V, OE should be tied to V
CC
through a pullup resistor;
the minimum value of the resistor is determined by the current-sinking capability of the driver.
The SN54ABT16245A is characterized for operation over the full military temperature range of 55
C to 125
C.
The SN74ABT16245A is characterized for operation from 40
C to 85
C.
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas
Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
Widebus, EPIC-IIB are trademarks of Texas Instruments.
PRODUCTION DATA information is current as of publication date.
Copyright 19942005, Texas Instruments Incorporated
Products conform to specifications per the terms of the Texas
On products compliant to MIL-PRF-38535, all parameters are
Instruments standard warranty. Production processing does not
tested unless otherwise noted. On all other products, production
necessarily include testing of all parameters.
processing does not necessarily include testing of all parameters.
www.ti.com
1A2
46
1A3
44
1A4
43
1A5
41
1A6
40
1A7
38
1A8
37
2A2
35
2A3
33
2A4
32
2A5
30
2A6
29
2A7
27
2A8
26
1OE
2OE
1A1
47
G3
48
3 EN1 [BA]
1
1DIR
3 EN2 [AB]
G6
25
6 EN4 [BA]
24
2DIR
6 EN5 [AB]
1B1
2
1B2
3
1B3
5
1B4
6
1B5
8
1B6
9
1B7
11
1B8
12
2A1
36
2B1
13
2B2
14
2B3
16
2B4
17
2B5
19
2B6
20
2B7
22
2B8
23
1
2
4
5
SN54ABT16245A, SN74ABT16245A
16-BIT BUS TRANSCEIVERS
WITH 3-STATE OUTPUTS
SCBS300F MARCH 1994 REVISED JULY 2005
FUNCTION TABLE
(EACH 8-BIT SECTION)
INPUTS
OPERATION
OE
DIR
L
L
B data to A bus
L
H
A data to B bus
H
X
Isolation
LOGIC SYMBOL
(1)
(1)
This symbol is in accordance with ANSI/IEEE Std 91-1984 and IEC Publication 617-12.
2
www.ti.com
To Seven Other Channels
1DIR
1A1
1B1
1OE
To Seven Other Channels
2DIR
2A1
2B1
2OE
1
47
24
36
48
2
25
13
Absolute Maximum Ratings
(1)
SN54ABT16245A, SN74ABT16245A
16-BIT BUS TRANSCEIVERS
WITH 3-STATE OUTPUTS
SCBS300F MARCH 1994 REVISED JULY 2005
LOGIC DIAGRAM (POSITIVE LOGIC)
over operating free-air temperature range (unless otherwise noted)
MIN
MAX
UNIT
V
CC
Supply voltage range
0.5
7
V
V
I
Input voltage range (except I/O ports)
(2)
0.5
7
V
V
O
Voltage range applied to any output in the high or power-off state
0.5
5.5
V
SN54ABT16245A
96
I
O
Current into any output in the low state
mA
SN74ABT16245A
128
I
IK
Input clamp current
V
I
< 0
18
mA
I
OK
Output clamp current
V
O
< 0
50
mA
DGG package
89
JA
Package thermal impedance
(3)
DGV package
93
C/W
DL package
94
T
stg
Storage temperature range
65
150
C
(1)
Stresses beyond those listed under "absolute maximum ratings" may cause permanent damage to the device. These are stress ratings
only, and functional operation of the device at these or any other conditions beyond those indicated under "recommended operating
conditions" is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability
(2)
The input and output negative-voltage ratings may be exceeded if the input and output clamp-current ratings are observed.
(3)
The package thermal impedance is calculated in accordance with JESD 51.
3
www.ti.com
Recommended Operating Conditions
(1)
SN54ABT16245A, SN74ABT16245A
16-BIT BUS TRANSCEIVERS
WITH 3-STATE OUTPUTS
SCBS300F MARCH 1994 REVISED JULY 2005
SN54ABT16245A SN74ABT16245A
UNIT
MIN
MAX
MIN
MAX
V
CC
Supply voltage
4.5
5.5
4.5
5.5
V
V
IH
High-level input voltage
2
2
V
V
IL
Low-level input voltage
0.8
0.8
V
V
I
Input voltage
0
V
CC
0
V
CC
V
I
OH
High-level output current
24
32
mA
I
OL
Low-level output current
48
64
mA
t/
v
Input transition rise or fall rate
Outputs enabled
10
10
ns/V
t/
V
CC
Power-up ramp rate
200
200
s/V
T
A
Operating free-air temperature
55
125
40
85
C
(1)
All unused inputs of the device must be held at V
CC
or GND to ensure proper device operation. Refer to the TI application report,
Implications of Slow or Floating CMOS Inputs, literature number SCBA004.
4
www.ti.com
Electrical Characteristics
SN54ABT16245A, SN74ABT16245A
16-BIT BUS TRANSCEIVERS
WITH 3-STATE OUTPUTS
SCBS300F MARCH 1994 REVISED JULY 2005
over recommended operating free-air temperature range (unless otherwise noted)
T
A
= 25
C
SN54ABT16245A SN74ABT16245A
PARAMETER
TEST CONDITIONS
UNIT
MIN TYP
(1)
MAX
MIN
MAX
MIN
MAX
V
IK
V
CC
= 4.5 V,
I
I
= 18 mA
1.2
8
1.2
1.2
V
V
CC
= 4.5 V,
I
OH
= 3 mA
2.5
2.5
2.5
V
CC
= 5 V,
I
OH
= 3 mA
3
3
3
V
OH
V
I
OH
= 24 mA
2
2
V
CC
= 4.5 V
I
OH
= 32 mA
2
(2)
2
I
OL
= 48 mA
0.55
0.55
V
OL
V
CC
= 4.5 V
V
I
OL
= 64 mA
0.55
(2)
0.55
V
hys
100
mV
Control
V
CC
= 0 to 5.5 V, V
I
= V
CC
or GND
1
1
1
inputs
I
I
A
A or B
V
CC
= 2.1 V to 5.5 V, V
I
= V
CC
or GND
20
(2)
100
20
port
I
OZPU
V
CC
= 0 to 2.1 V, V
O
= 0.5 V to 2.7 V, OE = X
50
(3)
50
(3)
50
A
I
OZPD
V
CC
= 2.1 V to 0, V
O
= 0.5 V to 2.7 V, OE = X
50
(3)
50
(3)
50
A
I
OZH
(4)
V
CC
= 2.1 V to 5.5 V, V
O
= 2.7 V, OE
2 V
10
(5)
10
10
(5)
A
I
OZL
(4)
V
CC
= 2.1 V to 5.5 V, V
O
= 0.5 V, OE
2 V
10
(5)
10
10
(5)
A
I
off
V
CC
= 0,
V
I
or V
O
5.5 V
100
100
A
V
CC
= 5.5 V,
I
CEX
Outputs high
50
50
50
A
V
O
= 5.5 V
I
O
(6)
V
CC
= 5.5 V,
V
O
= 2.5 V
50
100
180
50
180
50
180
mA
Outputs high
2
2
2
A or B
V
CC
= 5.5 V, I
O
= 0,
I
CC
Outputs low
32
32
32
mA
port
V
I
= V
CC
or GND
Outputs disabled
2
2
2
V
CC
= 5.5 V,
Outputs enabled
2
1.5
2
Data
One inputs at 3.4 V,
inputs
Other inputs at
Outputs disabled
0.05
1
0.05
I
CC
(7)
mA
V
CC
or GND
Control
V
CC
= 5.5 V, One input at 3.4 V,
1.5
1.5
1.5
inputs
Other inputs at V
CC
or GND
Control
C
i
V
I
= 2.5 V or 0.5 V
3
pF
inputs
A or B
C
o
V
O
= 2.5 V or 0.5 V
6
pF
port
(1)
All typical values are at V
CC
= 5 V.
(2)
On products compliant to MIL-PRF-38535, this parameter does not apply.
(3)
On products compliant to MIL-PRF-38535, this parameter is not production tested.
(4)
The parameters I
OZH
and I
OZL
include the input leakage current.
(5)
This limit may vary among suppliers.
(6)
Not more than one output should be tested at a time, and the duration of the test should not exceed one second.
(7)
This is the increase in supply current for each input that is at the specified TTL voltage level rather than V
CC
or GND.
5
www.ti.com
Switching Characteristics
Switching Characteristics
SN54ABT16245A, SN74ABT16245A
16-BIT BUS TRANSCEIVERS
WITH 3-STATE OUTPUTS
SCBS300F MARCH 1994 REVISED JULY 2005
over recommended operating ranges of supply voltage and operating free-air temperature, C
L
= 50 pF
(unless otherwise noted) (see
Figure 1
)
SN54ABT16245A
FROM
TO
V
CC
= 5 V,
PARAMETER
UNIT
(INPUT)
(OUTPUT)
T
A
= 25
C
MIN
MAX
MIN
TYP
MAX
t
PLH
0.5
2.2
3.4
0.5
4
A or B
B or A
ns
t
PHL
0.5
2.3
3.8
0.5
4.6
t
PZH
0.8
3.6
5.2
0.8
5.5
OE
B or A
ns
t
PZL
0.9
3.7
6.1
0.1
7.3
t
PHZ
1.3
4.4
5.8
1.3
6.3
OE
B or A
ns
t
PLZ
1.4
3.3
4.7
1.4
5.5
over recommended operating ranges of supply voltage and operating free-air temperature, C
L
= 50 pF
(unless otherwise noted) (see
Figure 1
)
SN74ABT16245A
FROM
TO
V
CC
= 5 V,
PARAMETER
UNIT
(INPUT)
(OUTPUT)
T
A
= 25
C
MIN
MAX
MIN
TYP
MAX
t
PLH
1
2.2
3.4
1
3.9
A or B
B or A
ns
t
PHL
1
2.3
3.7
1
4.2
t
PZH
1
3.6
5.2
1
6.3
OE
B or A
ns
t
PZL
1
3.7
5.4
1
6.4
t
PHZ
2
4.4
5.8
2
6.3
OE
B or A
ns
t
PLZ
1.5
3.3
4.7
1.5
5.2
6
www.ti.com
PARAMETER MEASUREMENT INFORMATION
1.5 V
t
h
t
su
From Output
Under Test
C
L
= 50 pF
(see Note A)
LOAD CIRCUIT
S1
7 V
Open
GND
500
500
Data Input
Timing Input
1.5 V
3 V
0 V
1.5 V
1.5 V
3 V
0 V
3 V
0 V
1.5 V
t
w
Input
VOLTAGE WAVEFORMS
SETUP AND HOLD TIMES
VOLTAGE WAVEFORMS
PROPAGATION DELAY TIMES
INVERTING AND NONINVERTING OUTPUTS
VOLTAGE WAVEFORMS
PULSE DURATION
t
PLH
t
PHL
t
PHL
t
PLH
V
OH
V
OH
V
OL
V
OL
1.5 V
1.5 V
3 V
0 V
1.5 V
1.5 V
Input
1.5 V
Output
Control
Output
Waveform 1
S1 at 7 V
(see Note B)
Output
Waveform 2
S1 at Open
(see Note B)
V
OL
V
OH
t
PZL
t
PZH
t
PLZ
t
PHZ
1.5 V
1.5 V
3.5 V
0 V
1.5 V
V
OL
+ 0.3 V
1.5 V
V
OH
- 0.3 V
0 V
3 V
VOLTAGE WAVEFORMS
ENABLE AND DISABLE TIMES
LOW- AND HIGH-LEVEL ENABLING
Output
Output
t
PLH
/t
PHL
t
PLZ
/t
PZL
t
PHZ
/t
PZH
Open
7 V
Open
TEST
S1
NOTES: A. C
L
includes probe and jig capacitance.
B. Waveform 1 is for an output with internal conditions such that the output is low, except when disabled by the output control.
Waveform 2 is for an output with internal conditions such that the output is high, except when disabled by the output control.
C. All input pulses are supplied by generators having the following characteristics: PRR
10 MHz, Z
O
= 50
, t
r
2.5 ns, t
f
2.5 ns.
D. The outputs are measured one at a time, with one transition per measurement.
1.5 V
SN54ABT16245A, SN74ABT16245A
16-BIT BUS TRANSCEIVERS
WITH 3-STATE OUTPUTS
SCBS300F MARCH 1994 REVISED JULY 2005
Figure 1. Load Circuit and Voltage Waveforms
7
PACKAGING INFORMATION
Orderable Device
Status
(1)
Package
Type
Package
Drawing
Pins Package
Qty
Eco Plan
(2)
Lead/Ball Finish
MSL Peak Temp
(3)
5962-9317501MXA
ACTIVE
CFP
WD
48
1
TBD
Call TI
Level-NC-NC-NC
74ABT16245ADGGRG4
ACTIVE
TSSOP
DGG
48
2000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
74ABT16245ADGVRE4
ACTIVE
TVSOP
DGV
48
2000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
SN74ABT16245ADGGR
ACTIVE
TSSOP
DGG
48
2000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
SN74ABT16245ADGVR
ACTIVE
TVSOP
DGV
48
2000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
SN74ABT16245ADL
ACTIVE
SSOP
DL
48
25
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
SN74ABT16245ADLR
ACTIVE
SSOP
DL
48
1000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
SN74ABT16245ADLRG4
ACTIVE
SSOP
DL
48
1000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
SNJ54ABT16245AWD
ACTIVE
CFP
WD
48
1
TBD
Call TI
Level-NC-NC-NC
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in
a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
Eco
Plan
-
The
planned
eco-friendly
classification:
Pb-Free
(RoHS)
or
Green
(RoHS
&
no
Sb/Br)
-
please
check
http://www.ti.com/productcontent
for the latest availability information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements
for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered
at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame
retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material)
(3)
MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder
temperature.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is
provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the
accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take
reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on
incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited
information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI
to Customer on an annual basis.
PACKAGE OPTION ADDENDUM
www.ti.com
26-Sep-2005
Addendum-Page 1
MECHANICAL DATA
MCFP010B JANUARY 1995 REVISED NOVEMBER 1997
POST OFFICE BOX 655303
DALLAS, TEXAS 75265
WD (R-GDFP-F**)
CERAMIC DUAL FLATPACK
4040176 / D 10/97
48 LEADS SHOWN
48
48
25
56
0.610
(18,80)
0.710
(18,03)
0.740
0.640
0.390 (9,91)
0.370 (9,40)
0.870 (22,10)
1.130 (28,70)
1
A
0.120 (3,05)
0.075 (1,91)
LEADS**
24
NO. OF
A MIN
A MAX
(16,26)
(15,49)
0.025 (0,635)
0.009 (0,23)
0.004 (0,10)
0.370 (9,40)
0.250 (6,35)
0.370 (9,40)
0.250 (6,35)
0.014 (0,36)
0.008 (0,20)
NOTES: A. All linear dimensions are in inches (millimeters).
B. This drawing is subject to change without notice.
C. This package can be hermetically sealed with a ceramic lid using glass frit.
D. Index point is provided on cap for terminal identification only
E. Falls within MIL STD 1835: GDFP1-F48 and JEDEC MO -146AA
GDFP1-F56 and JEDEC MO -146AB
MECHANICAL DATA
MPDS006C FEBRUARY 1996 REVISED AUGUST 2000
POST OFFICE BOX 655303
DALLAS, TEXAS 75265
DGV (R-PDSO-G**)
PLASTIC SMALL-OUTLINE
24 PINS SHOWN
14
3,70
3,50
4,90
5,10
20
DIM
PINS **
4073251/E 08/00
1,20 MAX
Seating Plane
0,05
0,15
0,25
0,50
0,75
0,23
0,13
1
12
24
13
4,30
4,50
0,16 NOM
Gage Plane
A
7,90
7,70
38
24
16
4,90
5,10
3,70
3,50
A MAX
A MIN
6,60
6,20
11,20
11,40
56
9,60
9,80
48
0,08
M
0,07
0,40
0
8
NOTES: A. All linear dimensions are in millimeters.
B. This drawing is subject to change without notice.
C. Body dimensions do not include mold flash or protrusion, not to exceed 0,15 per side.
D. Falls within JEDEC: 24/48 Pins MO-153
14/16/20/56 Pins MO-194
MECHANICAL DATA

MSSO001C JANUARY 1995 REVISED DECEMBER 2001
POST OFFICE BOX 655303
DALLAS, TEXAS 75265
DL (R-PDSO-G**)
PLASTIC SMALL-OUTLINE PACKAGE
4040048 / E 12/01
48 PINS SHOWN
56
0.730
(18,54)
0.720
(18,29)
48
28
0.370
(9,40)
(9,65)
0.380
Gage Plane
DIM
0.420 (10,67)
0.395 (10,03)
A MIN
A MAX
0.010 (0,25)
PINS **
0.630
(16,00)
(15,75)
0.620
0.010 (0,25)
Seating Plane
0.020 (0,51)
0.040 (1,02)
25
24
0.008 (0,203)
0.0135 (0,343)
48
1
0.008 (0,20) MIN
A
0.110 (2,79) MAX
0.299 (7,59)
0.291 (7,39)
0.004 (0,10)
M
0.005 (0,13)
0.025 (0,635)
0
8
0.005 (0,13)
NOTES: A. All linear dimensions are in inches (millimeters).
B. This drawing is subject to change without notice.
C. Body dimensions do not include mold flash or protrusion not to exceed 0.006 (0,15).
D. Falls within JEDEC MO-118
MECHANICAL DATA

MTSS003D JANUARY 1995 REVISED JANUARY 1998
POST OFFICE BOX 655303
DALLAS, TEXAS 75265
DGG (R-PDSO-G**)
PLASTIC SMALL-OUTLINE PACKAGE
4040078 / F 12/97
48 PINS SHOWN
0,25
0,15 NOM
Gage Plane
6,00
6,20
8,30
7,90
0,75
0,50
Seating Plane
25
0,27
0,17
24
A
48
1
1,20 MAX
M
0,08
0,10
0,50
0
8
56
14,10
13,90
48
DIM
A MAX
A MIN
PINS **
12,40
12,60
64
17,10
16,90
0,15
0,05
NOTES: A. All linear dimensions are in millimeters.
B. This drawing is subject to change without notice.
C. Body dimensions do not include mold protrusion not to exceed 0,15.
D. Falls within JEDEC MO-153
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications,
enhancements, improvements, and other changes to its products and services at any time and to discontinue
any product or service without notice. Customers should obtain the latest relevant information before placing
orders and should verify that such information is current and complete. All products are sold subject to TI's terms
and conditions of sale supplied at the time of order acknowledgment.
TI warrants performance of its hardware products to the specifications applicable at the time of sale in
accordance with TI's standard warranty. Testing and other quality control techniques are used to the extent TI
deems necessary to support this warranty. Except where mandated by government requirements, testing of all
parameters of each product is not necessarily performed.
TI assumes no liability for applications assistance or customer product design. Customers are responsible for
their products and applications using TI components. To minimize the risks associated with customer products
and applications, customers should provide adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right,
copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process
in which TI products or services are used. Information published by TI regarding third-party products or services
does not constitute a license from TI to use such products or services or a warranty or endorsement thereof.
Use of such information may require a license from a third party under the patents or other intellectual property
of the third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of information in TI data books or data sheets is permissible only if reproduction is without
alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction
of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for
such altered documentation.
Resale of TI products or services with statements different from or beyond the parameters stated by TI for that
product or service voids all express and any implied warranties for the associated TI product or service and
is an unfair and deceptive business practice. TI is not responsible or liable for any such statements.
Following are URLs where you can obtain information on other Texas Instruments products and application
solutions:
Products
Applications
Amplifiers
amplifier.ti.com
Audio
www.ti.com/audio
Data Converters
dataconverter.ti.com
Automotive
www.ti.com/automotive
DSP
dsp.ti.com
Broadband
www.ti.com/broadband
Interface
interface.ti.com
Digital Control
www.ti.com/digitalcontrol
Logic
logic.ti.com
Military
www.ti.com/military
Power Mgmt
power.ti.com
Optical Networking
www.ti.com/opticalnetwork
Microcontrollers
microcontroller.ti.com
Security
www.ti.com/security
Telephony
www.ti.com/telephony
Video & Imaging
www.ti.com/video
Wireless
www.ti.com/wireless
Mailing Address:
Texas Instruments
Post Office Box 655303 Dallas, Texas 75265
Copyright
2005, Texas Instruments Incorporated