DESCRIPTION
UCC5619 provides 27 lines of active termination for a SCSI (Small Com-
puter Systems Interface) parallel bus. The SCSI standard recommends ac-
tive termination at both ends of the cable.
The UCC5619 is ideal for high performance 5V SCSI systems. During dis-
connect the supply current is typically only 100
A, which makes the IC at-
tractive for lower powered systems.
The UCC5619 is designed with a low channel capacitance of 2.5pF, which
eliminates effects on signal integrity from disconnected terminators at in-
terim points on the bus.
The power amplifier output stage allows the UCC5619 to source full termi-
nation current and sink active negation current when all termination lines
are actively negated.
The UCC5619, as with all Unitrode terminators, is completely hot pluggable
and appears as high impedance at the teminating channels with V
TRMPWR
= 0V or open.
Internal circuit trimming is utilized, first to trim the 110
impedance, and
then most importantly, to trim the output current as close to the maximum
SCSI-3 specification as possible, which maximizes noise margin in fast
SCSI operation.
Other features include thermal shutdown and current limit. This device is
offered in low thermal resistance versions of the industry standard 36 pin
wide body QSSOP (MWP) and 48 pin LQFP (FQP).
Consult SSOP-36 (MWP QSSOP-36) and FQP-48 Packaging Diagram for
exact dimensions.
UCC5619
27-Line SCSI Terminator With Reverse Disconnect
BLOCK DIAGRAM
FEATURES
Complies with SCSI, SCSI-2, SCSI-3,
SPI and FAST-20 (Ultra) Standards
2.5pF Channel Capacitance during
Disconnect
100
A Supply Current in Disconnect
Mode
4V To 7V Operation
110
Termination
Completely Meets SCSI Hot Plugging
900mA Sourcing Current for
Termination
+500mA Sinking Current for Active
Negation
Logic Command Disconnects all
Termination Lines
Trimmed Impedance to 5%
Current Limit and Thermal Shutdown
Protection
10/98
UDG-96108
Circuit Design Patented
2
UCC5619
ABSOLUTE MAXIMUM RATINGS
TRMPWR Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . +7V
Signal Line Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . 0V to +7V
Regulator Output Current . . . . . . . . . . . . . . . . . . . . . . . . . . 1.5A
Storage Temperature . . . . . . . . . . . . . . . . . . .
-
65C to +150C
Junction Temperature . . . . . . . . . . . . . . . . . . .
-
55C to +150C
Lead Temperature (Soldering, 10 Sec.). . . . . . . . . . . . . +300C
Currents are positive into, negative out of the specified termi-
nal. Consult Packaging Section of Databook for thermal limita-
tions and considerations of packages.
LINE5
LINE6
LINE7
LINE22
LINE21
LINE19
LINE20
REG
LINE9
LINE8
GND*
LINE26
LINE27
LINE23
LINE24
LINE25
GND*
GND*
GND*
36
35
34
33
32
31
30
29
28
27
1
2
3
4
5
6
7
8
9
10
GND*
11
12
13
14
15
26
25
24
23
22
16
17
18
21
20
19
LINE12
LINE11
LINE10
DISCNCT
LINE13
LINE14
LINE1
LINE2
LINE17
LINE18
TRMPWR
GND*
LINE16
LINE15
LINE4
LINE3
* MWP package pins 8 - 10 and 26 - 28 serve as heatsink/
ground.
QSSOP-36 (Top View)
MWP Package
48
47
46
45
1
44
43
42
41
40
39
38
37
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
36
35
34
33
32
31
30
29
28
27
26
25
LINE 22
LINE 5
LINE 6
LINE 7
LINE 8
HS/GND
N/C
LINE 24
LINE 9
HS/GND
HS/GND
REG
LINE 19
LINE 20
LINE 21
TRMPWR
HS/GND
LINE 17
LINE 18
LINE 16
LINE 4
LINE 15
LINE 2
LINE 3
N/C
LINE 12
LINE 13
LINE 14
HS/GND
LINE 27
LINE 26
LINE 25
DISCNCT1
HS/GND
LINE 10
N/C
LINE 11
HS/GND
HS/GND
HS/GND
LINE 23
HS/GND
HS/GND
LINE 1
HS/GND
HS/GND
HS/GND
N/C
CONNECTION DIAGRAM
LFQP-48 (Top View)
FQP Package
ELECTRICAL CHARACTERISTICS
Unless otherwise stated, these specifications apply for T
A
= 0C to 70C,
TRMPWR = 4.75V, DISCNCT = 4.75V, T
A
= T
J
.
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
UNITS
Supply Current Section
TRMPWR Supply Current
All Termination Lines = Open
1
2
mA
All Termination Lines = 0.2V
630
650
mA
Power Down Mode
DISCNCT = 0V
100
200
A
Output Section (Termination Lines)
Termination Impedance
(Note 3)
104.5
110
115.5
Output High Voltage
(Note 1)
2.6
2.8
3.0
V
Max Output Current
V
LINE
= 0.2V, T
J
= 25C
-
22.1
-
23.3
-
24
mA
V
LINE
= 0.2V
-
20.7
-
23.3
-
24
mA
V
LINE
= 0.2V, TRMPWR = 4V, T
J
= 25
C (Note 1)
-
21
-
23
-
24
mA
V
LINE
= 0.2V, TRMPWR = 4V (Note 1)
-
20
-
23
-
24
mA
3
UCC5619
PIN DESCRIPTIONS
DISCNCT: Taking this pin low causes all channels to
become high impedance, and the chip to go into
low-power mode; a high state or leaving it open allows
the channels to provide normal termination.
GND: Ground reference for the IC.
LINE1 - LINE27: 110
termination channels.
REG: Output of the internal 2.7V regulator; bypass with a
4.7 F capacitor to GND.
TRMPWR: Power for the IC; bypass with a 4.7 F
capacitor to GND.
ELECTRICAL CHARACTERISTICS
Unless otherwise stated, these specifications apply for T
A
= 0C to 70C,
TRMPWR = 4.75V, DISCNCT = 4.75V, T
A
= T
J
.
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
UNITS
Output Section (CONT.)
V
LINE
= 0.5V
22.4
mA
Output Leakage
DISCNCT = 0V, TRMPWR = 0V to 5.25V
10
400
nA
Output Capacitance
DISCNCT = 0V (Note 2)
2.5
4
pF
Regulator Section
Regulator Output Voltage
2.6
2.8
3.0
V
Drop Out Voltage
All Termination Lines = 0.2V
0.4
0.8
V
Short Circuit Current
V
REG
= 0V
-
650
-
900
1300
mA
Sinking Current Capability
V
REG
= 3.5V
300
500
900
mA
Thermal Shutdown
170
C
Thermal Shutdown Hysteresis
10
C
Disconnect Section
Disconnect Threshold
0.8
1.5
2.0
V
Input Current
DISCNCT = 0V
20
60
A
11
29
25
TERMPWR
DISCNCT
DATA BYTES
1 AND 2
+2 PARITY BITS
7
REG
4.7
F
4.7
F
TO SCSI BUS
TERMPWR
17
LINE1
LINE27
CONTROL
BYTES
TO DRIVERS
AND
RECEIVERS
UCC5619
Figure 1. Typical wide SCSI bus configuration using the UCC5619
UDG-98072
UNITRODE CORPORATION
7 CONTINENTAL BLVD. MERRIMACK, NH 03054
TEL. (603) 424-2410 FAX (603) 424-3460
IMPORTANT NOTICE
Texas Instruments and its subsidiaries (TI) reserve the right to make changes to their products or to discontinue
any product or service without notice, and advise customers to obtain the latest version of relevant information
to verify, before placing orders, that information being relied on is current and complete. All products are sold
subject to the terms and conditions of sale supplied at the time of order acknowledgement, including those
pertaining to warranty, patent infringement, and limitation of liability.
TI warrants performance of its semiconductor products to the specifications applicable at the time of sale in
accordance with TI's standard warranty. Testing and other quality control techniques are utilized to the extent
TI deems necessary to support this warranty. Specific testing of all parameters of each device is not necessarily
performed, except those mandated by government requirements.
CERTAIN APPLICATIONS USING SEMICONDUCTOR PRODUCTS MAY INVOLVE POTENTIAL RISKS OF
DEATH, PERSONAL INJURY, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE ("CRITICAL
APPLICATIONS"). TI SEMICONDUCTOR PRODUCTS ARE NOT DESIGNED, AUTHORIZED, OR
WARRANTED TO BE SUITABLE FOR USE IN LIFE-SUPPORT DEVICES OR SYSTEMS OR OTHER
CRITICAL APPLICATIONS. INCLUSION OF TI PRODUCTS IN SUCH APPLICATIONS IS UNDERSTOOD TO
BE FULLY AT THE CUSTOMER'S RISK.
In order to minimize risks associated with the customer's applications, adequate design and operating
safeguards must be provided by the customer to minimize inherent or procedural hazards.
TI assumes no liability for applications assistance or customer product design. TI does not warrant or represent
that any license, either express or implied, is granted under any patent right, copyright, mask work right, or other
intellectual property right of TI covering or relating to any combination, machine, or process in which such
semiconductor products or services might be or are used. TI's publication of information regarding any third
party's products or services does not constitute TI's approval, warranty or endorsement thereof.
Copyright
1999, Texas Instruments Incorporated
PDF 
ZIP