SPECIFICATION
MODEL
DC VOLTAGE
RATED CURRENT
CURRENT RANGE
RATED POWER
OUTPUT
VOLTAGE ADJ. RANGE
LINE REGULATION
LOAD REGULATION
SETUP, RISE, HOLD TIME
VOLTAGE RANGE
FREQUENCY RANGE
EFFICIENCY(Typ.)
AC CURRENT
INPUT
INRUSH CURRENT(max.)
LEAKAGE CURRENT
WORKING HUMIDITY
WORKING TEMP.
STORAGE TEMP., HUMIDITY
TEMP. COEFFICIENT
VIBRATION
MTBF
DIMENSION
OTHERS
NOTE
PACKING
OVER LOAD
OVER VOLTAGE
12V
15V
24V
3.5A
2.8A
1.8A
0 ~ 3.5A
0 ~ 2.8A
0 ~ 1.8A
42W
43W
100mVp-p
100mVp-p
100mVp-p
1.0%
10.8 ~ 13.2V
13.5 ~ 16.5V
21.6 ~ 26.4V
1.0%
1.0%
0.5%
0.5%
0.5%
0.5%
0.5%
%
0.5
300ms, 50ms, 60ms/230VAC
800ms, 50ms, 15ms/115VAC at full load
85 ~ 264VAC
120 ~ 370VDC
47 ~ 63Hz
72%/115VAC
76%/115VAC
76%/115VAC
78%/115VAC
1.2A/115VAC
0.6A/230VAC
COLD START 30A/115VAC
60A/230VAC
<1mA / 240VAC
105 ~ 150% rated output power
Protection type : Hiccup mode, recovers automatically after fault condition is removed
Protection type : Hiccup mode, recovers automatically after fault condition is removed
-10 ~ +60
(Refer to output load derating curve)
20 ~ 90% RH non-condensing
-20 ~ +85
, 10 ~ 95% RH
0.03%/
(0 ~ 50
)
10 ~ 500Hz, 2G 10min./1cycle, period for 60min. each along X, Y, Z axes
314.1K hrs min.
MIL-HDBK-217F (25
)
129*98*38mm (L*W*H)
5V
8A
0 ~ 8A
40W
42W
75mVp-p
4.75 ~ 5.5V
2.0%
0.5%
1.0%
S-40-5
S-40-12
S-40-15
S-40-24
0.45Kg; 30pcs/13.5Kg/0.86CUFT
17.25 ~ 20.25
27.6 ~ 32.4V
13.8 ~ 16.2V
5.75 ~ 6.75V
SAFETY STANDARDS
UL1012, UL1950, TUV EN60950 Approved
Compliance to EN55022 (CISPR22) Class B
HARMONIC CURRENT
EMS IMMUNITY
Compliance to EN61000-3-2,-3
Compliance to EN61000-4-2,3,4,5; ENV50204, EN55024, Light industry level, criteria A
40W Single Output Switching Power Supply
Universal AC input / Full range
Protections:Short circuit/Over load
Cooling by free air convection
100% full load burn-in test
Fixed switching frequency at 36KHz
2 years warranty
Features :
S - 4 0
s e r i e s
WITHSTAND VOLTAGE
ISOLATION RESISTANCE
I/P-O/P, I/P-FG, O/P-FG:100M Ohms/500VDC
I/P-O/P:3KVAC
I/P-FG:1.5KVAC
O/P-FG:0.5KVAC
RIPPLE & NOISE (max.)
Note.2
VOLTAGE TOLERANCE
Note.3
EMI CONDUCTION & RADIATION
ENVIRONMENT
SAFETY &
EMC
(Note 4)
PROTECTION
1. All parameters NOT specially mentioned are measured at 230VAC input, rated load and 25
of ambient temperature.
2. Ripple & noise are measured at 20MHz of bandwidth by using a 12" twisted pair-wire terminated with a 0.1uf & 47uf parallel capacitor.
3. Tolerance : includes set up tolerance, line regulation and load regulation.
4. The power supply is considered a component which will be installed into a final equipment. The final equipment must be re-confirmed that it still meets
EMC directives.
TOTAL POWER INT'L
PDF 
ZIP