SPECIFICATION
SP-750-5
MODEL
DC VOLTAGE
RATED CURRENT
CURRENT RANGE
RATED POWER
OUTPUT
VOLTAGE ADJ. RANGE
LINE REGULATION
LOAD REGULATION
SETUP, RISE, HOLD TIME
VOLTAGE RANGE
FREQUENCY RANGE
EFFICIENCY (Typ.)
INPUT
INRUSH CURRENT (max.)
LEAKAGE CURRENT
OVER TEMPERATURE
WORKING TEMP.
REMOTE CONTROL
POWER GOOD/FAIL
WORKING HUMIDITY
STORAGE TEMP., HUMIDITY
TEMP. COEFFICIENT
VIBRATION
MTBF
DIMENSION
OTHERS
NOTE
PACKING
OVER LOAD
OVER VOLTAGE
AC CURRENT
5V
120A
0 ~ 120A
600W
120mVp-p
4.75 ~ 5.5V
2.0%
0.5%
2.0%
1000ms, 50ms, 16ms/230VAC
1000ms, 50ms, 16ms/115VAC at full load
90 ~ 264VAC
127 ~ 370VDC
47 ~ 63Hz
81%
11A/115VAC
5.3A/230VAC
30A/115VAC
50A/230VAC
<2.0mA / 240VAC
105~125% rated output power
5.75 ~ 6.3V
13.8 ~ 16.2V
18 ~ 21V
27.6 ~ 32.4V
31 ~ 36.5V
57.6 ~ 67.2V
Protection type : Constant current limiting, unit will Hiccup after 3 sec.
Protection type : Shut down o/p voltage, re-power on to recover
85
5
(TSW1 ) Detect on heatsink of power transistor
85
5
(TSW2 ) Detect on heatsink of power diode
Protection type : Shut down o/p voltage, recovers automatically after temperature goes down
-20 ~ +60
(Refer to output load derating curve)
RC+/RC- short power on, open power off
50ms/1ms
20~90% RH non-condensing
-40 ~ +85
, 10 ~ 95% RH
0.05%/
(0 ~ 50
)
10 ~ 500Hz, 2G 10min./1cycle, 60min. each along X, Y, Z axes
769.3K hrs min.
MIL-HDBK-217F (25
)
278*127*63.5mm (L*W*H)
2.9Kg; 6pcs / 18.4Kg / 0.98CUFT
86%
87%
89%
89%
90%
0.5%
0.5%
0.5%
0.5%
0.5%
0.3%
0.3%
0.2%
0.2%
0.2%
1.0%
1.0%
1.0%
1.0%
1.0%
120mVp-p
10 ~ 13.5V
120mVp-p
13.5 ~ 16.5V
120mVp-p
22 ~ 26.4V
120mVp-p
24 ~ 30V
120mVp-p
43 ~ 56V
12V
62.5A
0 ~ 62.5A
750W
15V
50A
0 ~ 50A
750W
24V
31.3A
0 ~ 31.3A
751.2W
27V
27.8A
0 ~ 27.8A
750.6W
48V
15.7A
0 ~ 15.7A
753.6W
SP-750-12
SP-750-15
SP-750-24
SP-750-27
SP-750-48
1. All parameters NOT specially mentioned are measured at 230VAC input, rated load and 25
of ambient temperature.
2. Ripple & noise are measured at 20MHz of bandwidth by using a 12" twisted pair-wire terminated with a 0.1uf & 47uf parallel capacitor.
3. Tolerance : includes set up tolerance, line regulation and load regulation.
4. The power supply is considered a component which will be installed into a final equipment. The final equipment must be re-confirmed that it still meets
EMC directives.
3
POWER FACTOR
0.95/230VAC
0.96/115VAC at full load
SAFETY STANDARDS
HARMONIC CURRENT
EMS IMMUNITY
UL60950-1, TUV EN60950-1 Approved
Compliance to EN55011 (CISPR11),
Class B
EN55022 (CISPR22)
Compliance to EN61000-3-2,-3
Compliance to EN61000-4-2,3,4,5,6,8,11, ENV50204, EN55024, EN61000-6-2, EN61204-3 Heavy industry level, criteria A
750W Single Output Power Supply
Universal AC input/Full range
AC input active surge current limiting
Built-in active PFC function,PF>0.95
Protections:Short circuit, overload, over voltage, over temperature
Forced air cooling by built-in DC ball bearing fan
High power density 5.48/inch
Built-in constant current limiting circuit
With power good and fail signal output
Built-in remote ON-OFF control
Built-in remote sense function
3 years warranty
Features :
S P - 7 5 0
s e r i e s
RIPPLE & NOISE (max.)
Note.2
VOLTAGE TOLERANCE
Note.3
EMI CONDUCTION & RADIATION
WITHSTAND VOLTAGE
ISOLATION RESISTANCE
I/P-O/P:3KVAC
I/P-FG:1.5KVAC
O/P-FG:0.5KVAC
I/P-O/P, I/P-FG, O/P-FG:100M Ohms/500VDC
ENVIRONMENT
SAFETY &
EMC
(Note 4)
PROTECTION
FUNCTION
TOTAL POWER INT'L
Total Power Int'l
418 Bridge Street
Lowell, MA 01850
PH: 978-453-7272 FX: 978-453-7395
Web: www.total-power.com Sales: sales@total-power.com
PDF 
ZIP