1345-Type Receiver with

Clock Recovery and Data Retiming

Data Sheet

February 2003

TriQuint Optoelectronics

Operating at 1.3

µm or 1.55 µm wavelengths and at

155 Mb/s or 622 Mb/s, the versatile 1345-Type Receiver is man-
ufactured in a 20-pin, plastic DIP with a multimode fiber pig-
tail.

Features

Backward compatible with 1330 family

Space-saving, self-contained, 20-pin plastic DIP

Silicon based ICs

Single 5 V power supply operation including
photocurrent monitor capability

Exceeds all SONET (GR-253-CORE) and ITU-T
G.958 jitter requirements

Clocked decision circuit

Regenerated differential clock signal

Wide dynamic range

Qualified to meet the intent of Telcordia Technolo-
gies

TM reliability practices

Operates at data rates of 155 Mb/s or
622 Mb/s

Positive ECL (PECL) data outputs

CMOS (TTL) link-status flag output

Operation at 1.3

µm or 1.55 µm wavelengths

Operating temperature range of 40 °C to +85 °C

Applications

Telecommunications:
-- Inter- and intraoffice SONET/ITU-T SDH
-- Subscriber loop
-- Metropolitan area networks

High-speed data communications

Description

The 1345-Type fiber-optic receiver is designed for
use in transmission systems or medium- to high-
speed data communication applications. Used in
intermediate- and long-reach applications, the
receiver operates at the SONET OC-3 or OC-12 data
rate as well as the ITU-T synchronous digital hierar-
chy (SDH) rate of STM-1 or STM-4, depending on
the receiver model chosen. The receiver meets all
present Telcordia Technologies GR-253-CORE
requirements, the current ANSI T1X1.5 intraoffice
specifications, and the ITU-T G.957 and G.958 rec-
ommendations. Compact packaging, a high level of
integration, and a wide dynamic range make these
receivers ideal for data communications.

Manufactured in a 20-pin DIP, the receiver consists
of a planar InGaAs PIN photodetector, a silicon
preamplifier, a silicon bipolar limiting amplifier that
converts the small signal to ECL levels, a timing
recovery unit to recover the clock, and a silicon bipo-
lar decision circuit.

riQ

uint

SEM

ICO

NDU

CTO

Rec

eive

134

5-Ty

2
2

For additional information and latest specifications, see our website: www.triquint.com

1345-Type Receiver with

Data Sheet

Clock Recovery and Data Retiming

February 2003

Description

(continued)

The receiver converts optical signals in the range of
1.1

µm to 1.6 µm into retimed clock and data signals.

The clock and data outputs are raised-ECL (PECL)
logic levels. A CMOS-level flag output indicates when
there is a loss of optical signal.

The receiver requires a 5 V power supply for the ampli-
fier, logic, and PLL CRC circuits. The operating case
temperature range is 40 °C to +85 °C.

Pin 10

Pin 10 on the 1345-Type receiver is not an internally
connected (NIC) pin. This definition allows the 1345 to
be used in most customer 20-pin receiver module
applications. Customer's printed-wiring boards that are
designed with ground, +5 V, 5 V, or no connection to
this pin are all acceptable options. For those applica-
tions that require monitoring the photocurrent of the
PIN photodetector for power monitoring purposes,
there are versions of the 1345 that require +5 V or 5 V
applied to Pin 10. Check Tables 3 and 4 for ordering
information.

Flag Output

When the optical input falls below the link status flag
switching threshold, the link status flag is deactivated
and its output logic level changes from a CMOS logic
HIGH to a CMOS logic LOW.

Squelched Data and Clock Outputs

In some versions of the 1345 receiver (see Table 4),
when the link status flag is deactivated, the data and
clock outputs are squelched (stop outputting a signal).
When this occurs, the DATA, DATA, CLOCK, and
CLOCK

outputs switch to a constant dc output voltage

level of 1.3 V.

Nonsquelched Data and Clock Outputs

TriQuint also manufactures nonsquelching versions of
the 1345 receiver for those applications that require the
data and clock outputs to continue to function after the
link status flag is deactivated. In those versions of the
receiver, when the link status flag is deactivated, a sig-
nal will continue to appear at the DATA, DATA, CLOCK,
and CLOCK outputs. See Table 4 for nonsquelching
codes.

1-724(C)

Figure 1. Block Diagram

FILTER

PREAMPLIFIER

InGaAs

SILICON BIPOLAR

LIMITING AMPLIFIER

5 V

DATA

SILICON BIPOLAR

DECISION CIRCUIT

FLAG

PLL TIMING

RECOVERY UNIT

CLOCK

FLAG

OPTIONAL V

For additional information and latest specifications, see our website: www.triquint.com

Data Sheet

1345-Type Receiver with

February 2003

Clock Recovery and Data Retiming

Absolute Maximum Ratings

Stresses in excess of the absolute maximum ratings can cause permanent damage to the device. These are abso-
lute stress ratings only. Functional operation of the device is not implied at these or any other conditions in excess
of those given in the operational sections of the data sheet. Exposure to absolute maximum ratings for extended
periods can adversely affect device reliability.

Parameter

Symbol

Min

Max

Unit

Supply Voltage

5.5

Operating Case Temperature Range

°C

Storage Case Temperature Range

stg

°C

Lead Soldering Temperature/Time

250/10

°C/s

Operating Wavelength Range

1.1

1.6

µm

Minimum Fiber Bend Radius

1.0 (25.4)

in. (mm)

Pin Information

* Pins designated as no user connection are not connected inter-

nally. However, to allow for future functional upgrades, it is recom-
mended that the user not make any connections to these pins.

The link status flag is a logic flag that indicates the presence or

absence of a minimum acceptable level of optical input. A logic
high on the FLAG output indicates the presence of a valid optical
signal.

Mounting and Connections

The pigtail consists of a 39 in. ± 4 in. (1 m ± 10 cm),
62.5

µm core/125 µm cladding multimode fiber. The

standard fiber has a 0.036 in. (914 µm) diameter tight-
buffered outer-jacket. The minimum fiber bending
radius during operation is 1.0 in. (25.4 mm).

Electrostatic Discharge

CAUTION: This device is susceptible to damage

as a result of electrostatic discharge
(ESD). Take proper precautions during
both handling and testing. Follow guide-
lines such as EIA

Standard EIA-625.

Although protection circuitry is designed into the
device, take proper precautions to avoid exposure to
ESD.

TriQuint. employs a human-body model (HBM) for ESD
susceptibility testing and protection-design evaluation.
ESD voltage thresholds are dependent on the critical
parameters used to define the model. A standard HBM
(resistance = 1.5 k

capacitance = 100 pF) is widely

used and, therefore, can be used for comparison pur-
poses. The HBM ESD threshold established for the
1345 receiver is ±1000 V.

Receiver Processing

The 1345-Type receiver devices can withstand normal
wave-soldering processes. The complete receiver
module is not hermetically sealed; therefore, it should
not be immersed in or sprayed with any cleaning solu-
tion or solvents. The process cap and fiber pigtail
jacket can deform at temperatures greater than 85 °C.
The receiver pins can be wave-soldered at maximum
temperature of 250 °C for 10 seconds.

Pin

Name

Pin

Name

Ground

No User Connection*

Ground

No User Connection*

Ground

No User Connection*

CLOCK

No User Connection*

CLOCK

Ground

DATA

FLAG

Ground

DATA

FLAG

No Internal
Connection or
Optional V

1345-Type Receiver with

Data Sheet

Clock Recovery and Data Retiming

February 2003

4
4

For additional information and latest specifications, see our website: www.triquint.com

Application Information

The 1345 receiver is a highly sensitive fiber-optic
receiver. Although the data outputs are digital logic lev-
els (PECL), the device should be thought of as an ana-
log component. When laying out the printed-wiring
board (PWB), the 1345 receiver should be given the
same type of consideration one would give to a sensi-
tive analog component.

At a minimum, a double-sided printed-wiring board with
a large component-side ground plane beneath the
receiver must be used. In applications that include
many other high-speed devices, a multilayer PWB is
highly recommended. This permits the placement of
power and ground connections on separate layers,
which helps minimize the coupling of unwanted signal
noise into the power supplies of the receiver.

Layout Considerations

A fiber-optic receiver employs a very high-gain, wide-
bandwidth transimpedance amplifier. The amplifier
detects and amplifies signals that are only tens of nA in
amplitude. Any unwanted signal currents that couple
into the receiver circuitry cause a decrease in the
receiver's sensitivity and can also degrade the perfor-
mance of the receiver's loss of signal (FLAG) circuit. To
minimize the coupling of unwanted noise into the
receiver, route high-level, high-speed signals such as
transmitter inputs and clock lines as far away as possi-
ble from the receiver pins. If this is not possible, then
the PWB layout engineer should consider interleaving
the receiver signal and flag traces with ground traces in
order to provide the required isolation.

Noise that couples into the receiver through the power
supply pins can also degrade device performance. The
application schematics, Figures 2--3, show recom-
mended power supply filtering that helps minimize
noise coupling into the receiver. The bypass capacitors
should be high-quality ceramic devices rated for RF
applications. They should be surface-mount compo-
nents placed as close as possible to the receiver power
supply pins. The ferrite bead should have as high an
impedance as possible in the frequency range that is
most likely to cause problems. This will vary for each
application and is dependent on the signaling frequen-
cies present on the application circuit card. Surface-
mount, high-impedance beads are available from sev-
eral manufacturers.

Data and Flag Outputs

The data and clock outputs of the 1345 receiver are
driven by open-emitter NPN transistors which have an
output impedance of approximately 7

. Each output

can provide approximately 50 mA maximum output
current. Due to the high switching speeds of ECL out-
puts, transmission line design must be used to inter-
connect components. To ensure optimum signal fidelity,
both data outputs (DATA and DATA) and clock outputs
(CLOCK and CLOCK) should be terminated identically.
The signal lines connecting the data and clock outputs
to the next device should be equal in length and should
have matched impedances.

Controlled impedance stripline or microstrip construc-
tion must be used in order not to degrade the quality of
the signal into the next component and to minimize
reflections back into the receiver. Excessive ringing
due to reflections caused by improperly terminated sig-
nal lines makes it difficult for the component receiving
these signals to decipher the proper logic levels and
may cause transitions to occur where none were
intended. Also, by minimizing high frequency ringing
due to reflections caused by improperly designed and
terminated signal lines, possible EMI problems can be
avoided. The applications sections in the Signetics

ECL 10K/100K Data Manual or the National Semicon-
ductor

ECL Logic Databook and Design Guide pro-

vide excellent design information on ECL interfacing.

The FLAG and FLAG

outputs of the OC-3/STM-1

155 Mb/s receiver and the OC-12/STM-4 622 Mb/s
receiver are 5 V TTL logic-level compatible. The FLAG
output is provided directly by the comparator IC. How-
ever, the FLAG output is derived from the FLAG output
through an inverter. Excessive loading of the FLAG
output can cause the FLAG output to malfunction.

Recommended User Interface

The 1345 receiver is designed to be operated from a
5 V power supply and provides raised or pseudo-ECL
(PECL) data outputs. Figures 2 and 3 show two possi-
ble application circuits for the 1345 receiver. Figure 2
represents an application for a PECL compatible inter-
face while Figure 3 shows a possible application for an
ac-coupled, ECL-compatible interface. In both
instances, the DATA outputs are terminated with a
Thévenin equivalent circuit, which provides the equiva-
lent of a 50

load terminated to (V

2 V). A single

resistor terminated to (V

2 V) could also be

used, but this requires a second power supply. Other
methods of terminating ECL-type outputs are dis-
cussed in the references previously mentioned.

1345-Type Receiver with

Data Sheet

Clock Recovery and Data Retiming

February 2003

6
6

For additional information and latest specifications, see our website: www.triquint.com

Installation Considerations

Although the receiver has been designed with ruggedness in mind, care should be used during handling. The opti-
cal connector should be kept free from dust, and the process cap should be kept in place as a dust cover when the
device is not connected to a cable. If contamination is present on the optical connector, the use of canned air with
an extension tube should remove any debris. Other cleaning procedures are identified in the Cleaning Fiber-Optic
Assemblies Technical Note (TN95-010LWP).

Characteristics

Minimum and maximum values specified over operating case temperature range and end-of-life (EOL). Typical val-

ues are measured at beginning-of-life (BOL) room temperature unless otherwise noted.

Table 1. Electrical Characteristics

1. Customers have the option for either a +5 V or 5 V supply.
2. Includes approximately 50 mA of DATA and CLOCK output termination current.
3. Measured with 50

load terminated to (V

2.00) V.

4. DATA and CLOCK outputs are 10K ECL compatible.
5. Measured as shown in Figure 4.
6. Measured with an input data pseudorandom word 2

Parameter

Symbol

Min

Typ

Max

Unit

dc Power Supply Voltages

4.75

5.0

5.25

PIN Photodetector Supply Voltage (Pin 10)

4.75

5.25

5.0

5.25

4.75

V
V

dc Power Supply Currents:

OC-3/STM-1 Version
OC-12/STM-4 Version

--
--

110

150

150
200

mA
mA

Output Data/Clock Voltage:

3, 4

Low
High

1.95

1.03

1.63

0.88

V
V

Output Data/Clock Rise and Fall Time:

OC-3/STM-1 Version
OC-12/STM-4 Version

1100

320

1300

360

1700

500

ps
ps

Output Flag Voltage:

Low
High

0.5

--
--

0.6

V
V

Clock/Data Alignment:

OC-3/STM-1 Version

OC-12/STM-4 Version

CDA

800
300

--
--

800
300

ps
ps

Clock Duty Cycle

Output Clock Random Jitter:

OC-3/STM-1 Version
OC-12/STM-4 Version

--
--

0.003
0.005

0.008

0.01

UI
UI

Output Clock Jitter Peaking

0.04

0.05

0.1

Jitter Tolerance

Telcordia Technologies GR-253-CORE and ITU-T G.958 Compliant

Jitter Transfer

Telcordia Technologies GR-253-CORE and ITU-T G.958 Compliant

For additional information and latest specifications, see our website: www.triquint.com

Data Sheet

1345-Type Receiver with

February 2003

Clock Recovery and Data Retiming

Characteristics

(continued)

Table 2. Optical Characteristics

* For a 1 x 10

BER. Measured with a 2

1 pseudorandom word optical input having a 50% average duty cycle.

Whenever the flag output is deasserted (logic low), the DATA and CLOCK outputs are silenced. See the Flag Output section on

page 2 for the DATA and CLOCK output signal levels.

Power supply noise in excess of 50 mVp-p may degrade the performance of the receiver. See User Interface section for recom-

mended power supply filtering.

1-725(C)

Figure 4. Clock/Data Alignment

Parameter

Symbol

Data Rates

Mb/s

Min

Typ

Max

Unit

Measured Average Sensitivity:*

OC-3
OC-12

OC-3/STM-1

OC-12/STM-4

--
--

32.5

36
30

dBm
dBm

Maximum Input Power

MAX

OC-3/STM-1

OC-12/STM-4

--
--

dBm
dBm

Link Status Flag Threshold:

Decreasing Light Input

LST

OC-3/STM-1

OC-12/STM-4

OC-3/STM-1

OC-12/STM-4

50
50
50
50

38.8

38
35

37.5
32.5
37.0
32.0

dBm
dBm
dBm
dBm

Flag Hysteresis

HYS

155/622

0.5

Flag Response Time

FLAG

155/622

100

µs

Detector Responsivity

155/622

0.7

0.8

1.2

A/W

50%

CLOCK

OUT

DATA

OUT

CDA

For additional information and latest specifications, see our website: www.triquint.com

1345-Type Receiver with

Data Sheet

Clock Recovery and Data Retiming

February 2003

PWB Layout Guidelines

Follow high-speed ECL design rules.

All high-speed output lines must be controlled-impedance lines, and the termination impedance must match
the line impedance. Controlled-impedance interruptions should be avoided (i.e., 90° bends, etc.) and paired lines
(i.e., DATA and

DATA

) should be of equal length.

Each output line should be terminated at the end of the line and must have a bypass capacitor on the voltage
side of the resistor for each termination.

Data and clock output lines should be as short and as straight as possible and isolated from noise sources (and
each other) to prevent noise from feeding back into the receiver.

Noise that couples into the receiver through the power supply pins can degrade device performance. See
Figure 2 for an example of power supply filtering for the receiver 5 V power supply pins.

Use a multilayer board so that the ground plane surrounds the areas occupied by the receiver and directly under-

neath it. Directly attach all pins listed as ground pins to the ground plane with no additional lead length.

All unused outputs must be terminated as shown. All resistors are 1/8 W, thin-film, ceramic chips. All capacitors are

25 Vdc, ceramic X7R or equivalent.

Qualification and Reliability

To help ensure high product reliability and customer satisfaction, TriQuint is committed to an intensive quality pro-
gram that starts in the design phase and proceeds through the manufacturing process. Optoelectronics modules
are qualified to TriQuint internal standards using MIL-STD-883 test methods and procedures and using sampling
techniques consistent with Telcordia Technologies requirements. The 1345 series of receivers have undergone an
extensive and rigorous set of qualification tests. This qualification program fully meets the intent of Telcordia Tech-
nologies reliability practices TR-NWT-000468 and TA-NWT-000983. In addition, the design, development, and
manufacturing facility of the Optoelectronics unit at TriQuint is certified to be in full compliance with the latest ISO

9001 Quality System Standards.

For additional information and latest specifications, see our website: www.triquint.com

1345-Type Receiver with

Data Sheet

Clock Recovery and Data Retiming

February 2003

Ordering Information

Table 3. OC-3/STM-1 Receiver Versions

* These versions have nonsquelching data and clock outputs. See Nonsquelched Data and Clock Outputs section on page 2.

Table 4. OC-12/STM-4 Receiver Versions

* These versions have nonsquelching data and clock outputs. See Nonsquelched Data and Clock Outputs section on page 2.

Table 5. Related Products

Device Code

Pin 10 Requirements

Connector

Comcode

1345FMPC

Internal

Connections

FC-PC

108339979

1345CMPC

108354473

1345TMPC

108572421

1345FMPD

FC-PC

108354515

1345CMPD

108354481

1345TMPD

108572439

1345FAPC

Requires

+5 V

5 V

FC-PC

108468687

1345CAPC

108359175

1345TAPC

108572249

1345FAPD*

FC-PC

108572322

1345CAPD*

108572280

1345TAPD*

108572389

Device Code

Pin 10 Requirements

Connector

Comcode

1345FNPC

Internal

Connections

FC-PC

108155722

1345CNPC

107354499

1345TNPC

108572447

1345FNPD

FC-PC

108354523

1345CNPD

108354507

1345TNPD*

108572454

1345FBPC

Requires

+5 V

5 V

FC-PC

108572355

1345CBPC

108572298

1345TBPC

108572397

1345FBPD*

FC-PC

108573965

1345CBPD*

108572306

1345TBPD*

108572413

Description

Document Number

1241/1243/1245-Type Receivers for SONET/SDH Applications

00-228

1340-Type Receiver with Clock Recovery and Data Retiming

DS00-098

Additional Information

For the latest specifications, additional product information, worldwide sales and distribution locations, and information about TriQuint:

Web: www.triquint.com

Tel: (503) 615-9000

E-mail: info_opto@tqs.com

Fax: (503) 615-8902

For technical questions and additional information on specific applications:

E-mail: info_opto@tqs.com

The information provided herein is believed to be reliable; TriQuint assumes no liability for inaccuracies or omissions. TriQuint assumes no responsibility for the use of this information, and all
such information shall be entirely at the user's own risk. Prices and specifications are subject to change without notice. No patent rights or licenses to any of the circuits described herein are
implied or granted to any third party.
TriQuint does not authorize or warranty any TriQuint product for use in life-support devices and/or systems.

DS00-099 Revision 1.1, February, 2003

1345-Type Receiver with

Data Sheet

Clock Recovery and Data Retiming

February 2003

Telcordia Technologies is a trademark of Telcordia Technologies Inc.

EIA is a registered trademark of Electronic Industries Association.

Signetics is a registered trademark of Signetics Corp.

National Semiconductor is a registered trademark of National Semiconductor Corporation.

ISO is a registered trademark of The International Organization for Standardization.

Document Outline

Ð­Ð»ÐµÐºÑ‚Ñ€Ð¾Ð½Ð½Ñ‹Ð¹ ÐºÐ¾Ð¼Ð¿Ð¾Ð½ÐµÐ½Ñ‚: 1345FAPD

Document Outline

ÐÐ»ÐµÐºÑ‚Ñ€Ð¾Ð½Ð½Ñ‹Ð¹ ÐºÐ¾Ð¼Ð¿Ð¾Ð½ÐµÐ½Ñ‚: 1345FAPD