Data Sheet
Part Number 855738
70 MHz SAW Filter
Subject to change or obsolescence without notice
Rev A
23-May-2002
Page 1 of 5
Features
For broadband applications
Typical 3dB bandwidth of 1 MHz
High attenuation
Single-ended operation
Ceramic Surface Mount Package (SMP)
Replaces Sawtek P/N 851545 (BW 3dB=1.5 MHz)
Package
Pin Configuration
Surface Mount 24.60 x 9.00 x 2.31 mm
Bottom View
6
7
10 9 8
5
4
3
2
1
Pin No. Description
5
Output
10
Input
1,2,3,4
6,7,8,9
Case Ground
Case Ground
R0.5
2.31
2.31 NOM.
2.62 MAX.
3.53 x 4.83
1.02
1.80
9.00
1.02
1.91
24.6
Dimensions shown are nominal in millimeters
All tolerances are
0.15mm except overall
length
0.20mm and width +0.13/-0.20mm
Body: Al
2
O
3
ceramic
Lid: Kovar, Ni plated
Terminations: Au plating 0.5 - 1.0
m,
over a 2 - 6
m Ni plating
Data Sheet
Part Number 855738
70 MHz SAW Filter
Subject to change or obsolescence without notice
Rev A
23-May-2002
Page 2 of 5
Electrical Specifications
(1)
Operating Temperature Range:
(2)
0 to +70
o
C
Parameter
(3)
Minimum
Typical
Maximum
Unit
Center Frequency
- 70 -
MHz
Minimum Insertion Loss
- 21.6 23
dB
Lower 1 dB Bandedge
(4)
Upper 1 dB Bandedge
-
70.65
69.30
70.70
69.35
-
MHz
MHz
Lower 3 dB Bandedge
(4)
Upper 3 dB Bandedge
-
70.78
69.18
70.81
69.22
-
MHz
MHz
Lower 40 dB Bandedge
(4)
Upper 40 dB Bandedge
68.71
-
68.74
71.26
-
71.29
MHz
MHz
Amplitude Variation
69.35
-
70.65
MHz
-
0.64
1
dB p-p
Phase Linearity
69.35
-
70.65
MHz
-
2.4
5
deg p-p
Group Delay Variation
69.35
-
70.65
MHz
-
97
200
nsec
Relative Attenuation
(4)
10
-
68
MHz
72
-
110
MHz
110
-
118
MHz
118
-
124
MHz
124
-
133
MHz
133
-
200
MHz
50
50
30
50
30
50
64
60
35
66
37
66
-
-
-
-
-
-
dB
dB
dB
dB
dB
dB
Source Impedance
(5)
- 50 -
Load Impedance
(5)
- 50 -
Substrate Material
- Quartz
- -
Notes:
1. All specifications are based on the test circuit shown below
2. In production, devices will be tested at room temperature to a guardbanded specification to ensure electrical compliance over
temperature
3. Electrical margin has been built into the design to account for the variations due to temperature drift and manufacturing tolerances
4. All attenuation measurements are measured relative to minimum insertion loss
5. This is the optimum impedance in order to achieve the performance shown
Test Circuit:
Actual matching values may vary due to PCB layout and parasitics
50
Single-ended
1,2,3,4
6,7,8,9
50
330nH
10
5
270nH
50
Data Sheet
Part Number 855738
70 MHz SAW Filter
Subject to change or obsolescence without notice
Rev A
23-May-2002
Page 3 of 5
Typical Performance
(at +25
o
C)
Data Sheet
Part Number 855738
70 MHz SAW Filter
Subject to change or obsolescence without notice
Rev A
23-May-2002
Page 4 of 5
Matching Schematics
50
Single-ended
1,2,3,4
6,7,8,9
50
330nH
10
5
270nH
50
Marking
PCB Footprint
XXXXXX
855738
SAWTEK
Date code
ID dot
1.95
1.22
.69
9.19
8.84
Date code is the day of the current year in Julian format, last digit
of the year, and hour of the day
This footprint represents a recommendation only
Dimensions shown are nominal in millimeters
Tape and Reel
9.39
0.20
2.6
Section A-A
R0.75
12.0
A
1.5
25.6
2.0
0.36
20.2
1.75
4.0
1.5
A
40.4
44.0
20.2
13.0
2.7
102
330
44.8
Direction of travel
2.0
ID dot
Dimensions shown are nominal in millimeters
Packaging quantity: 1000 units/reel
Data Sheet
Part Number 855738
70 MHz SAW Filter
Subject to change or obsolescence without notice
Rev A
23-May-2002
Page 5 of 5
Maximum Ratings
Parameter
Symbol
Minimum
Maximum
Unit
Operating Temperature Range
T
0
+70
o
C
Storage Temperature Range
T
stg
-40 +85
o
C
Warnings
Electrostatic Sensitive Device (ESD)
Avoid ultrasonic exposure
Links to Additional Technical Information
PCB Layout Tips
Qualification Flowchart
Soldering Profile
S-Parameters
Other Technical Information
Sawtek's liability is limited only to the Surface Acoustic Wave (SAW) component(s) described in this data sheet. Sawtek does not accept any liability for
applications, processes, circuits or assemblies which are implemented using any Sawtek component described in this data sheet.
Contact Information
PO Box 609501
Orlando, FL 32860-9501
USA
Phone: +1 (407) 886-8860
Fax: +1 (407) 886-7061
Email:
custservice@sawtek.com
Web:
www.sawtek.com
Or contact one of our worldwide
network of
sales offices,
representatives or distributors
PDF 
ZIP