Preliminary Data Sheet
Part Number 856020
140 MHz SAW Filter
Subject to change or obsolescence without notice
Rev C
17-Jun-2002
Page 1 of 5
Features
For broadband applications
Typical 3dB bandwidth of 65 MHz
High attenuation
Single-ended operation
Ceramic Surface Mount Package (SMP)
Small size
Replaces Sawtek P/N 851948 (BW 3dB=64 MHz)
Package
Pin Configuration
Surface Mount 9.00 x 7.01 x 1.50 mm
Bottom View
5
4
10
9
8
7
6
3
2
1
Pin No.
Description
4
Output
5
Output
return
9
Input
10
Input
return
1,2,3,6,7,8
Case
ground
0.76
9.00
2.54
2.54
1.12
1.02
7.01
1.80
1.50 NOM.
1.65 MAX.
1.02 x 2.54
Dimensions shown are nominal in millimeters
All tolerances are
0.15mm except overall
length and width +0.10mm/-0.15mm
Body: Al
2
O
3
ceramic
Lid: Kovar, Ni plated
Terminations: Au plating 0.5 - 1.0
m,
over a 2 - 6
m Ni plating
Preliminary Data Sheet
Part Number 856020
140 MHz SAW Filter
Subject to change or obsolescence without notice
Rev C
17-Jun-2002
Page 2 of 5
Electrical Specifications
(1)
Operating Temperature Range:
(2)
0 to +70
o
C
Parameter
(3)
Minimum
Typical
Maximum
Unit
Center Frequency
- 140 -
MHz
Minimum Insertion Loss -
17.8
20
dB
Lower 1 dB Bandedge
(4)
Upper 1 dB Bandedge
-
168.25
108.85
170.27
111.75
-
MHz
MHz
Lower 3 dB Bandedge
(4)
Upper 3 dB Bandedge
-
171.5
107.45
172.61
108.5
-
MHz
MHz
Lower 40 dB Bandedge
(4)
Upper 40 dB Bandedge
98
-
102.35
180.78
-
182
MHz
MHz
Amplitude Variation
111.75 - 168.25
MHz
-
0.6
1.0
dB p-p
Phase Linearity
111.75 - 168.25
MHz
-
5.35
10
deg p-p
Group Delay Variation
111.75 - 168.25
MHz
-
21
55
ns p-p
Absolute Delay
- 0.539 -
sec
Relative Attenuation
(4)
15
-
75
MHz
75
-
98
MHz
182
-
205
MHz
205
-
350
MHz
45
40
40
45
51
50
43
50
-
-
-
-
dB
dB
dB
dB
Terminating Source Impedance
(5)
- 50 -
Terminating Load Impedance
(5)
- 50 -
Substrate Material
- 128
LiNbO
3
- -
Temperature Coefficient of Frequency
- -74 -
ppm/
o
C
Notes:
1. All specifications are based on the test circuit shown below
2. In production, devices will be tested at room temperature to a guardbanded specification to ensure electrical compliance over
temperature
3. Electrical margin has been built into the design to account for the variations due to temperature and manufacturing tolerances
4. All attenuation measurements are measured relative to minimum insertion loss
5. This is the optimum impedance in order to achieve the performance shown
Test Circuit:
Actual matching values may vary due to PCB layout and parasitics
50
Single-ended
1,2,3,5
6,7,8,10
50
27nH
9
4
56nH
50
47pF 33nH
22pF
Preliminary Data Sheet
Part Number 856020
140 MHz SAW Filter
Subject to change or obsolescence without notice
Rev C
17-Jun-2002
Page 3 of 5
Typical Performance
(at +25
o
C)
Preliminary Data Sheet
Part Number 856020
140 MHz SAW Filter
Subject to change or obsolescence without notice
Rev C
17-Jun-2002
Page 4 of 5
Matching Schematics
Actual matching values may vary due to PCB layout and parasitics
50
Single-ended
1,2,3,5
6,7,8,10
50
27nH
9
4
56nH
50
47pF 33nH
22pF
Marking
PCB Footprint
Date code
ID dot
SAWTEK
XXXXXX
856020
1.22
9.19
1.32
1.22
3.76
1.32
1.32
2.07
7.21
The date code consists of: day of the current year (Julian,
3 digits), last digit of the year (1 digit) and hour (2 digits)
This footprint represents a recommendation only
Dimensions shown are nominal in millimeters
Tape and Reel
A
A
1.5
12.0
4.0
1.5
2.0
9.22
7.22
2.2
Section A-A
0.3
16.0
7.5
1.75
13.0
20.2
102
330
16.8
2.7
ID dot
Direction of travel
2.0
Dimensions shown are nominal in millimeters
Packaging quantity: 2000 units/reel
Preliminary Data Sheet
Part Number 856020
140 MHz SAW Filter
Subject to change or obsolescence without notice
Rev C
17-Jun-2002
Page 5 of 5
Maximum Ratings
Parameter
Symbol
Minimum
Typical Maximum
Unit
Operating Temperature Range
T
0
+25
+70
o
C
Storage Temperature Range
T
stg
-40 - +85
o
C
Warnings
Electrostatic Sensitive Device (ESD)
Avoid ultrasonic exposure
Links to Additional Technical Information
PCB Layout Tips
Qualification Flowchart
Soldering Profile
S-Parameters
Reel and Packaging Label
Other Technical Information
Sawtek's liability is limited only to the Surface Acoustic Wave (SAW) component(s) described in this data sheet. Sawtek does not accept any liability for
applications, processes, circuits or assemblies which are implemented using any Sawtek component described in this data sheet.
Contact Information
PO Box 609501
Orlando, FL 32860-9501
USA
Phone: +1 (407) 886-8860
Fax: +1 (407) 886-7061
Email:
custservice@sawtek.com
Web:
www.sawtek.com
Or contact one of our worldwide
Network of
sales offices,
Representatives or distributors
PDF 
ZIP