Preliminary Data Sheet
Part Number 856327
915 MHz SAW Filter
Features
For ISM band applications
Usable bandwidth 26 MHz
Low loss
High attenuation
No impedance matching required for operation
at 50
Single-ended operation
Chip Scale Package (CSP)
Small size
Package
Pin Configuration
Surface Mount 2.00 x 1.50 x 0.76 mm
Bottom View
3
4
2
1
Pin No.
Description
1
Input
3
Output
2,4
Case
ground
0.76 NOM.
0.84 MAX.
1.30
1.50
0.42
0.56
0.25x45 CHAMFER
1.80
2.00
Dimensions shown are nominal in millimeters
All tolerances are
0.10mm
Body: Al
2
O
3
ceramic
Lid: Kovar or Alloy 42, Au over Ni plated
Terminations: Au plating 0.5 - 1.0
m,
over a 2 - 6
m Ni plating
Subject to change or obsolescence without notice
Rev -
15-Dec-2003
Page 1 of 5
Preliminary Data Sheet
Part Number 856327
915 MHz SAW Filter
Electrical Specifications
(1)
Operating Temperature Range:
(2)
-30 to +85
o
C
Parameter
(3)
Minimum
Typical
(4)
Maximum
Unit
Center Frequency
- 915 -
MHz
Maximum Insertion Loss
902
-
928
MHz
-
2.3
3.0
dB
Absolute Attenuation
10
-
857.5
MHz
857.5 - 882.5 MHz
970
-
1005
MHz
1005
-
1110
MHz
1110
-
3000
MHz
40
35
35
40
30
47
43
40
50
30
-
-
-
-
-
dB
dB
dB
dB
dB
Amplitude Ripple
902
-
928
MHz
-
0.35
1
dB p-p
Group Delay Variation
902
-
928
MHz
-
15
50
nS p-p
Input/Output Return Loss
902
-
928
MHz
10
14
-
dB
Source Impedance
(5)
- 50 -
Load Impedance
(5)
- 50 -
Notes:
1. All specifications are based on the test circuit shown below
2. In production, devices will be tested at room temperature to a guardbanded specification to ensure electrical compliance over
temperature
3. Electrical margin has been built into the design to account for the variations due to temperature drift and manufacturing tolerances
4. Typical values are given at 25
o
C
5. This is the optimum impedance in order to achieve the performance shown
Test Circuit:
50
Single-ended
2,4
1
3
50
50
No impedance matching
required
Subject to change or obsolescence without notice
Rev -
15-Dec-2003
Page 2 of 5
Preliminary Data Sheet
Part Number 856327
915 MHz SAW Filter
Typical Performance
(at +25
o
C)
Subject to change or obsolescence without notice
Rev -
15-Dec-2003
Page 3 of 5
Preliminary Data Sheet
Part Number 856327
915 MHz SAW Filter
Matching Schematics
50
Single-ended
2,4
1
3
50
50
No impedance matching
required
Marking
PCB Footprint
Marking
code
MFG site
5 M
WWY
ID dot
Date code
0.31x45
CHAMFER
0.76
2.00
0.62
1.50
This footprint represents a recommendation only
Dimensions shown are nominal in millimeters
Tape and Reel
1.83
Section A-A
0.3
1.09
2.34
1.5
1.0
4.0
4.0
2.0
A
A
8.0
3.5
1.75
8.8
ID dot
2.0
Direction of travel
330
20.2
13.0
102
2.7
Dimensions shown are nominal in millimeters
Packaging quantity: 10000 units/reel
Subject to change or obsolescence without notice
Rev -
15-Dec-2003
Page 4 of 5
Preliminary Data Sheet
Part Number 856327
915 MHz SAW Filter
Maximum Ratings
Parameter
Symbol
Minimum
Maximum
Unit
Operating Temperature Range
T
-30
+85
o
C
Storage Temperature Range
T
stg
-40 +85
o
C
Warnings
Electrostatic Sensitive Device (ESD)
Avoid ultrasonic exposure
Links to Additional Technical Information
PCB Layout Tips
Qualification Flowchart
S-Parameters
Sawtek's liability is limited only to the Surface Acoustic Wave (SAW) component(s) described in this data sheet. Sawtek does not accept any liability for
applications, processes, circuits or assemblies which are implemented using any Sawtek component described in this data sheet.
Contact Information
PO Box 609501
Orlando, FL 32860-9501
USA
Phone: +1 (407) 886-8860
Fax: +1 (407) 886-7061
Email:
custservice@sawtek.com
Web:
www.sawtek.com
Or contact one of our worldwide
Network of
sales offices,
Representatives or distributors
Soldering Profile
Other Technical Information
Subject to change or obsolescence without notice
Rev -
15-Dec-2003
Page 5 of 5
PDF 
ZIP