Vectron International, 267 Lowell Rd, Hudson NH 03051-4916 Tel: 1-88-VECTRON-1
Website: www.vectron.com
Page 1 of 6
Rev: Jan 17 2005
Data Sheet
VC-710
Voltage Controlled Crystal Oscillator
Features
Small Industry Standard Package, 5.0 x 7.5 x 1.8 mm
Output Frequencies from 120 MHz to 200 MHz
3.3 V Operation
HFF crystal for ultra low jitter
Complementary PECL Outputs
Low phase noise and custom options
0/70
C or 40/85
C operating temperature
Enable /Disable (PECL)
RoHS compliant lead free construction
Applications
PLL circuits for Clock Smoothing and Frequency Translation
Fiber Channel
SONET
SDH, ITU-T G.709
SONET, GR-253-CORE Issue3
Description
The VC-710 is a voltage controlled crystal oscillator that
operates at the fundamental frequency of the internal HFF
crystal. The HFF crystal is a high-Q quartz device that
enables the circuit to achieve low phase jitter performance
over a wide operating temperature range. The oscillator is
housed in an industry standard hermetically sealed leadless
surface mount package and is available on tape and reel.
VC-710 Voltage Controlled Crystal Oscillator
Vectron International, 267 Lowell Rd, Hudson NH 03051-4916 Tel: 1-88-VECTRON-1
Website: www.vectron.com
Page 2 of 6
Rev: Jan 17 2005
Electrical Performance
Parameter
Symbol
Min
Typical
Maximum
Units
Frequency
f
O
120
155.52
200
MHz
Supply Voltage (+3.3 V)
V
DD
3.135
3.3
3.465
V
Supply Current
I
DD
50
<90
mA
Output Logic Levels
Output Logic High +25 C
Output Logic Low +25 C
V
OH
V
OL
Vcc -1.025
Vcc -1.810
Vcc -0.950
Vcc -1.700
Vcc -0.880
Vcc -1.620
V
V
Transition Times
Rise Time
Fall Time
t
R
t
F
0.5
0.5
1
1
ns
ns
Symmetry or Duty Cycle
SYM
45
50
55
%
Operating temperature (ordering option)
0/70 or 40/85
C
Jitter (12 kHz 20 MHz BW), 155.52 MHz
0.3
ps (rms)
Jitter (50 kHz 80 MHz BW), 155.52 MHz
0.5
ps (rms)
Phase Noise, f
0
= 155.52 MHz
10 Hz offset
100 Hz offset
1kHz offset
10 kHz offset
100 kHz offset
1 MHz offset
10 MHz offset
-64
-95
-123
-143
-146
-146
-146
dBc/Hz
dBc/Hz
dBc/Hz
dBc/Hz
dBc/Hz
dBc/Hz
dBc/Hz
Test Conditions for APR (+3.3V)
V
C
0.3
3.0
V
Absolute Pull Range (APR)
APR
+ 50
ppm
Gain Transfer
Positive, 65
ppm/V
Control Voltage Bandwidth (-3dB)
BW
20
100
kHz
Package Size
5.0 x 7.5 x 1.8
mm
V
OL
50%
V
OH
80%
20%
t
R
t
F
t
A
t
B
SYM = 100 x t
A
/ t
B
Figure 2. PECL Waveform
1
2
3
6
5
4
50
50
Test Circuit Notes:
1) To Permit 50
Measurement of Outputs, all DC Inputs are Biased Down 1.3V.
2) All Voltage Sources Contain Bypass Capacitors to Minimize Supply Noise.
3) 50
Terminations are Within Test Equipment.
(-1.3V to +2V)
(-1.3V)
(+2V)
COutput
Output
>1.4V or Open
Figure 1. Test Circuit ( 3.3 V)
VC-710 Voltage Controlled Crystal Oscillator
Vectron International, 267 Lowell Rd, Hudson NH 03051-4916 Tel: 1-88-VECTRON-1
Website: www.vectron.com
Page
3
of 6
Rev: Jan 17 2005
VC-710 Voltage Controlled Crystal Oscillator
Vectron International, 267 Lowell Rd, Hudson NH 03051-4916 Tel: 1-88-VECTRON-1
Website: www.vectron.com
Page
4
of 6
Rev: Jan 17 2005
Outline Diagram
Pad Layout
Pin Out
Pin
Symbol
Function
1
V
C
VCXO Control Voltage
2
OE
Enable / Disable
Enabled = High or Open
Disabled = Low
High impedance output (Oscillator running)
3
GND
Case and Electrical Ground
4
Output
Output
5
COutput
Complementary Output
6
V
CC
Power Supply Voltage (3.3 V)
Tape and Reel (EIA-481-2-A)
Tape Dimensions (mm)
Reel Dimensions (mm)
Dimension
W
F
Do
Po
P1
A
B
C
D
N
W1
W2 # Per
Tolerance
Typ
Typ
Typ
Typ
Typ
Typ
Min
Typ
Min
Min
Typ
Max
Reel
VC-710
16
7.5
1.5
4
8
178
1.5
13
20.2
50
16.4
22.4
200
Po
W
A
N
F
P1
W1
W2
C
B
D
Do
mm
[inch]
5.08
[0.200]
2.54
[0.100]
1.78
[0.070]
3.66
[0.144]
1.96
[0.077]
V C 7 1 0 D F F G F A
X X X . X X X
V I Y W W
5 . 0 8 0 . 1 5
[ 0 . 2 0 0 0 . 0 0 6 ]
1 . 2 7
[ 0 . 0 5 0 ]
5 . 0 8
[ 0 . 2 0 0 ]
m m
[ i n c h ]
6
5
4
1
2
3
1 . 2 7
[ 0 . 0 5 0 ]
1 . 9 1
[ 0 . 0 7 5 ]
R 0 . 6 4
[ 0 . 0 2 5 ]
7 . 4 9 0 . 1 5
[ 0 . 2 9 5 0 . 0 0 6 ]
1 . 7 7 0 . 1 8
[ 0 . 0 7 0 0 . 0 0 7 ]
2 . 5 4
[ 0 . 1 0 0 ]
VC-710 Voltage Controlled Crystal Oscillator
Vectron International, 267 Lowell Rd, Hudson NH 03051-4916 Tel: 1-88-VECTRON-1
Website: www.vectron.com
Page
5
of 6
Rev: Jan 17 2005
Absolute Maximum Ratings
Parameter
Symbol
Ratings
Unit
Power Supply
V
CC
0 to 6
V
Voltage Control Range
V
C
0 to V
CC
V
Storage Temperature
TS
-55 to 125
C
Soldering Temp/Time
T
LS
240/10
C/sec
Stresses in excess of the absolute maximum ratings can permanently damage the device. Functional operation is not implied at these or
any other conditions in excess of conditions represented in the operational sections of this data sheet. Exposure to absolute maximum
ratings for extended periods may adversely affect device reliability.
Reliability
The VC-710 family is capable of meeting the following qualification tests:
Environmental Compliance
Parameter
Conditions
Mechanical Shock
MIL-STD-883, Method 2002
Mechanical Vibration
MIL-STD-883, Method 2007
Solderability
MIL-STD-883, Method 2003
Gross and Fine Leak
MIL-STD-883, Method 1014
Resistance to Solvents
MIL-STD-883, Method 2015
Handling Precautions
Although ESD protection circuitry has been designed into the VC-710 proper precautions should be taken when handling and mounting.
VI employs a human body model and a charged-device model (CDM) for ESD susceptibility testing and design protection evaluation.
ESD Ratings
Model
Minimum
Conditions
Human Body Model
500
MIL-STD 883, Method 3015
Charged Device Model
500
JESD 22-C101
Recommended Solder Reflow Profile
VI qualification includes aging at various extreme temperatures, shock and vibration, temperature cycling, and IR
reflow simulation. The conditions a device can withstand are well understood and devices can be subjected to the
profile above. This profile shows a ramp up condition to prevent thermal shock, a preheat period in which the flux is
activated, a ramp up to 183
C which is the reflow temperature of Sn/Pb eutectic, and a gradual cool down. The
time above 183
C should not exceed 60 seconds and the peak temperature should be no more than 220
C for 10
seconds. The VC-710's are hermetically sealed so an aqueous wash is not an issue.
PDF 
ZIP