Document Number: 42033
Revision 17-Nov-03
www.vishay.com
98
Type 131P
Vishay Sprague
For technical questions, contact spresale@vishay.com
FEATURES
Suggested replacement for Type 196P
Moderate cost
Small size
High peak current ratings
High corona starting voltage
DC Life Test: 140% of rated voltage for 250 hours @ + 125C.
No open or short circuits. No visible damage. Maximum
Capacitance Change: 5%. Minimum IR = 60% of initial limit.
Maximum DF = 1.0%.
Moisture Resistance: MIL-STD-202, Method 106E, 10
cycles. No visible damage. Maximum Capacitance Change:
3%. Minimum IR = 60% of initial limit. Maximum DF = 1.2%.
Thermal Shock and Immersion Cycling: No visible damage.
Maximum Capacitance Change: 1%. Minimum IR = 50% of
initial limit. Maximum DF = 1.2%.
0.010
0.022
0.047
0.10
0.22
0.47
131P103X9600S02*
131P223X9600S02*
131P473X9600S02*
131P104X9600S02
131P224X9600S02
131P474X9600S02
0.312 x 0.875 [7.92 x 22.23]
0.400 x 0.875 [10.16 x 22.23]
0.400 x 1.375 [10.16 x 34.93]
0.562 x 1.375 [14.27 x 34.93]
0.670 x 1.625 [17.02 x 41.28]
0.750 x 2.375 [19.05 x 60.33]
0.037
0.058
0.085
0.149
0.354
0.656
1.5
3.3
7.0
15.0
33.0
70.0
0.025
0.041
0.059
0.104
0.247
0.459
1.0
2.3
4.9
10.5
23.1
49.0
ORDERING INFORMATION
* All standard inventoried Part Numbers will be stocked in terminal and case style number S04.
1000 WVDC / 500 VAC
0.010
0.022
0.047
0.10
0.22
0.47
131P103X91K0S02*
131P223X91K0S02*
131P473X91K0S02*
131P104X91K0S02*
131P224X91K0S02*
131P474X91K0S02*
0.400 x 0.875 [10.16 x 22.23]
0.400 x 1.375 [10.16 x 34.93]
0.562 x 1.375 [14.27 x 34.93]
0.670 x 1.625 [17.02 x 41.28]
0.750 x 2.125 [19.05 x 53.98]
1.000 x 2.375 [25.40 x 60.33]
0.039
0.079
0.133
0.241
0.427
0.772
2.5
5.5
11.0
25.0
55.0
117.0
0.027
0.055
0.093
0.168
0.298
0.540
1.7
3.8
7.7
17.5
38.5
81.9
PERFORMANCE CHARACTERISTICS
Operating Temperature: - 65C to + 125C.
Capacitance Range: 0.01F to 0.47F.
Capacitance Tolerance: 20%, 10%, 5%, 2%.
Voltage Rating: 600 WVDC to 1000 WVDC.
Dissipation Factor: 1.0% maximum.
Voltage Test: 200% of rated DC voltage for 2 minutes.
Insulation Resistance: At + 25C: 20,000 Megohm -
Microfarads or 30,000 Megohm minimum. At + 125C:
20 Megohm - Microfarads or 250 Megohm minimum.
Capacitance Change with Temperature: At - 65C,
- 10% typical. At + 125C, + 10% typical.
STANDARD RATINGS in inches [millimeters]
PART NUMBER
10%
TOLERANCE
CAPACITANCE
(
F)
NOMINAL CASE SIZE
D x L
Max. rms
CURRENT
@ +
85
C
Max.
PEAK
CURRENT
@ + 85
C
Max. rms
CURRENT
@ +
125
C
Max.
PEAK
CURRENT
@ + 125
C
PHYSICAL CHARACTERISTICS
Lead Pull: 5 pounds (2.3 kilograms) for one minute.
No physical damage.
Lead Bend: After three complete consecutive bends, no damage.
Lead Wire: Bare, solid tinned wire. Case Diameters: .312"
[7.92mm], No. 22 AWG; .400" [10.16mm] and over, No. 20 AWG.
Marking: Sprague
trademark, type or part number,
capacitance and voltage.
131P
TYPE
This is expressed in picofarads.
The first two digits are the
significant figures. The third is the
number of zeros to follow. Values
must conform to the decade rating
for the tolerance specified.
103
CAPACITANCE
X9
CAPACITANCE
TOLERANCE
X0 = 20%
X9 = 10%
(Inventoried)
X5 = 5%
X2 = 2%
600
DC VOLTAGE
RATING
This is expressed in
volts. (1000 WVDC
coded as 1K0)
S = Wire leads
T = Soldering tab*
S
TERMINAL
Note: Inventoried
items are all S04.
04
CASE
STYLE
* Soldering tabs are available only on case diameters equal to or greater
than 0.400" [10.16mm]. Consult the factory for special case styles and
terminal configurations.
ENVIRONMENTAL CHARACTERISTICS
Vibration Test (Condition B): No mechanical
damage, short, open or intermittent circuits.
Film Snubber Capacitors
Metal-Case, Paper/Polyester, Dielectric
Extended Foil Electrodes
600 WVDC / 370 VAC
Legal Disclaimer Notice
Vishay
Document Number: 91000
www.vishay.com
Revision: 08-Apr-05
1
Notice
Specifications of the products displayed herein are subject to change without notice. Vishay Intertechnology, Inc.,
or anyone on its behalf, assumes no responsibility or liability for any errors or inaccuracies.
Information contained herein is intended to provide a product description only. No license, express or implied, by
estoppel or otherwise, to any intellectual property rights is granted by this document. Except as provided in Vishay's
terms and conditions of sale for such products, Vishay assumes no liability whatsoever, and disclaims any express
or implied warranty, relating to sale and/or use of Vishay products including liability or warranties relating to fitness
for a particular purpose, merchantability, or infringement of any patent, copyright, or other intellectual property right.
The products shown herein are not designed for use in medical, life-saving, or life-sustaining applications.
Customers using or selling these products for use in such applications do so at their own risk and agree to fully
indemnify Vishay for any damages resulting from such improper use or sale.
PDF 
ZIP