1
White Electronic Designs Corporation (508) 366-5151 www.whiteedc.com
Sept. 2002 Rev. 2A
ECO #15633
EDI7F341MC
EDI7F341MC-BNC: 1Mx32 80 PIN SIMM
1Mx32 and 2x1Mx32 Densities
Based on Intel's E28F008SA Flash Device
Fast Read Access Time - 90ns
5- Volt-Only Reprogramming or 12V Reprogram.
Low Power Dissipation
60mA per Device Active Current
10A per Device CMOS Standby Current
Typical Endurance >100,000 Cycles
Single 5 Volt +10% Supply
CMOS and TTL Compatible Inputs and Outputs
Commercial and Industrial Temperature Range
Package
80 Pin SIMM (JEDEC)
The EDI7F341MC and EDI7F2341MC are organized as one and
two banks of 1Mx32 respectively. The modules are based on Intel's
E28F008SA - 1Mx8 Flash device in TSOP packages which are
mounted on an FR4 substrate.
Both modules offer access times between 90 and 150ns allowing
for operation of high-speed microprocessors without wait states.
EDI7F2341MC-BNC: 2x1Mx32 80 PIN SIMM
BLOCK DIAGRAMS
FEATURES
DESCRIPTION
1Mx32 FLASH MODULE
FIG. 1
A0-A19
G\
DQ0-DQ7
DQ8-DQ15
DQ16-DQ23
DQ24-DQ31
1Mx8
1Mx8
1Mx8
1Mx8
E0\
W0\
W1\
W2\
W3\
A0-A19
G\
DQ0-DQ7
DQ8-DQ15
DQ16-DQ23
DQ24-DQ31
1Mx8
1Mx8
1Mx8
1Mx8
1Mx8
1Mx8
1Mx8
1Mx8
E1\
E0\
W0\
W1\
W2\
W3\
2
White Electronic Designs Corporation (508) 366-5151 www.whiteedc.com
Sept. 2002 Rev. 2A
ECO #15633
EDI7F341MC
PIN CONFIGURATIONS
A0-A19
Address input
E0\,E1\
Chip Enable
W0\-W3\
Write Enable
G\
Output Enable
DQ0-DQ31
Data Input/Output
PD
Presence Detect
VCC
Power 5 V +10%
VSS
Ground
NC
No Connect
CAPACITANCE
(f=1.0MHz, VIN = VCC or VSS)
Presence Detect Pin Out
Pin
1Meg
2x1Meg
PD1
NC
VSS
PD2
VSS
VSS
PD3
NC
NC
PD4
VSS
VSS
Simm Density
Pin
1Meg
2x1Meg
21
NC
NC
22
NC
NC
23
NC
E1\
24
E0\
E0\
*TBD
1Meg
2x1Meg
Parameter
Sym
Max
Max
Unit
Address Lines
CA
35
70
pF
Data lines
CDQ
15
30
pF
Chip & Write
CC
15
30
pF
Enable Lines
Output Enable lines
CG
35
70
pF
Pin
Pin
Pin
Pin
Pin
Pin
Pin
Pin
#
Name
#
Name
#
Name
#
Name
1
VSS
21
*
41
A11
61
DQ9
2
VCC
22
*
42
A10
62
DQ8
3
VPP
23
*
43
A9
63
DQ7
4
G\
24
*
44
A8
64
DQ6
5
W0\
25
VSS
45
A7
65
DQ5
6
W1\
26 DQ29
461
A6
66
DQ4
7
NC
27 DQ30
47
A5
67
DQ3
8
DQ16
28 DQ31
48
A4
68
DQ2
9
DQ17
29
W2\
49
A3
69
DQ1
10
DQ18
30
NC
50
A2
70
DQ0
11
DQ19
31
NC
51
A1
71
VPP
12
DQ20
32
NC
52
AO
72
VCC
13
DQ21
33
A19
53
W3\
73
PD1
14
DQ22
34
A18
54
VSS
74
PD2
15
DQ23
35
A17
55
DQ15
75
PD3
16
DQ24
36
A16
56
DQ14
76
PD4
17
DQ25
37
A15
57
DQ13
77
PD5
18
DQ26
38
A14
58
DQ12
78
PD6
19
DQ27
39
A13
59
DQ11
79
PD7
20
DQ28
40
A12
60
DQ10
80
VSS
3
White Electronic Designs Corporation (508) 366-5151 www.whiteedc.com
Sept. 2002 Rev. 2A
ECO #15633
EDI7F341MC
ORDERING INFORMATION
PACKAGE NO. 362: 80 PIN SIMM (JEDEC)
PACKAGE NO. 363: 80 PIN SIMM (JEDEC)
Note: For gold contact option, change EDI7F to EDI7G.
Note: For gold contact option, change EDI7F to EDI7G.
8
G
P
1
4
3
2
7
6
5
9
P1
9
4.384
0.125 DIA (2x)
4.655 MAX.
0.250
0.050 TYP.
4.150
2.245
2.192
0.400
MAX.
0.850
R 0.062 (2x)
0.250
MAX.
0.125
MIN.
0.120
8
G
P
1
4
3
2
7
6
5
9
P1
4.384
0.125 DIA (2x)
4.655 MAX.
0.250
0.050 TYP.
2.245
2.192
4.150
0.062 R. (2x)
0.250
0.850
MAX.
0.400
0.170
MAX.
MIN.
0.225
0.125
MIN.
Part Number
Speed
Package
(ns)
No.
EDI7F341MC90BNC
90
362
EDI7F341MC100BNC
100
362
EDI7F341MC120BNC
120
362
EDI7F341MC150BNC
150
362
Part Number
Speed
Package
(ns)
No.
EDI7F2341MC90BNC
90
363
EDI7F2341MC100BNC
100
363
EDI7F2341MC120BNC
120
363
EDI7F2341MC150BNC
150
363
ALL DIMENSIONS ARE IN INCHES
ORDERING INFORMATION
DATASHEET APPROVALS
ECO#
EDI PART NO.
NEW REV
DATE
APPROVAL:
INITIAL
DATE
CORRECTION ON PAGES
JUAN GUZMAN
MUKESH TRIVEDI
PAUL MARIEN
LARRY WINROTH
DAVE KELLY
MARK DOWNEY
DAVE HARRISON
TONY LEE
BOB KHEDERIAN
LUIS ESTELLA
YES
NO
LINE
:________
WILL THIS DATASHEET GO ON THE WEB?
FAMILY:
____________
PROD.TYPE:
________
ORG:___________
IS THIS A NEW DATASHEET?
DENSITY:________
SPEED:__________
WILL THIS DATASHEET REPLACE AN EXISTING
PKG:____________
DATASHEET THAT'S ALREADY ON THE WEB?
VOLTAGE:________
IF YES, WHAT DATASHEET IS IT REPLACING?
WHAT SECTION SHOULD THIS DATASHEET BE
PLACED IN ON THE WEB?
AFTER REVIEWING OR MAKING CORRECTIONS ON THE DATASHEET (S)
PLEASE SIGN-OFF ON THIS SHEET AND ,MAKE YOUR CORRECTIONS ON
THE ORIGINAL COPY(S).
AFTER REVIEWING THE DATA SHEET, TEST ENGINEERING WILL COMPLETE THE SECTION BELOW.
TEST PROGRAM CHANGE REQUIRED:
YES:_________NO____________DATE:___________
TEST ENGINEER SIGNATURE___________________
IF YES, DO NOT RELEASE DATA SHEET UNTIL TEST PROGRAM CHANGE IS COMPLETED.
TEST PROGRAM CHANGE COMPLETION DATE:__________
TEST PROGRAM NAME AND REVISION_________________
TEST ENGINEER SIGNATURE__________________________
FO-00342R1.DOC
ECO# 14942
SHEET 1 OF
1
10/1/02
10/2/02
10/2/02
L.K.
M.A.
EDI7F341MC
2A
15633
10/1/02
PDF 
ZIP