W528SXX

ADPCM VOICE SYNTHESIZER

(PowerSpeech)

Publication Release Date: Nov 2000

- 1 - Revision A1

GENERAL DESCRIPTION

The W528xxx family are programmable speech synthesis ICs that utilize the ADPCM coding method to
generate all types of voice effects.

The W528xxx's LOAD and JUMP commands and four programmable registers provide powerful user-
programmable functions that make this chip suitable for an extremely wide range of speech IC
applications.

The W528xxx family includes 12 kinds of bodies which are the same except for the voice duration
shown below:

BODY

W528S03 W528S05 W528S08A W528S10 W528S12

W528S15

Second

3 Sec

5 Sec

8 Sec

10 Sec

12 Sec

15 Sec

BODY

W528S20 W528S25

W528S30

W528S40 W528S50

W528S60

Second

20 Sec

25 Sec

30 Sec

40 Sec

50 Sec

60 Sec

Note: The voice durations are estimated by 6.4KHz sampling rate.

FEATURES

Programmable speech synthesizer

Wide operating voltage range: 2.4 to 5.5 volts

4-bit ADPCM synthesis method

Provides 4 direct trigger inputs that can easily be extended to 8 or 12 matrix trigger inputs

Two trigger input debounce times (20 to 40 mS or 160 to 320

S) can be set

Provides up to 2 LEDs and 3 STOP outputs

Every LED pin can drive 3 LEDs simultaneously

LED flash frequency: 3 Hz

AUD output current: 5 mA

Flexible functions programmable through the following:

LD (load), JP (jump) commands

Four registers: R0, EN, STOP, and MODE

Conditional instructions

Speech equation

END instruction

Global repeat (GR) setting

Output frequency and LED flash type setting

Programmable power-on initialization (POI) (can be interrupted by trigger inputs)

W528SXX

- 2 -

POI delay time of 160 mS ensures stable voltage when chip is powered on

Can be programmed for the following functions:

Interrupt or non-interrupt for rising or falling edge of each trigger pin (this feature determines

retriggerable, non-retriggerable, overwrite, and non-overwrite features of each trigger pin)

Four playing modes:

One Shot (OS)

Level Hold (LH)

Single-cycle level hold (S_LH)

Complete-cycle level hold (C_LH)

Stop output signal setting

Serial, direct, or random trigger mode setting

Four frequency options (4/4.8/6/8 KHz) and LED On/Off control can be set independently in each

GO instruction of speech equation

Independent control of LED1 and LED2

Total of 256 voice group entries available for programming

Provides the following mask options:

LED flash type: synchronous/alternate

LED1 section-controlled: Yes/No

LED2: section-controlled/STPC-controlled

LED volume-controlled: No/Yes

PAD CONFIGURATIONS

TG4/LED2/STPC

W5285-9

W5281-4

TEST

TG1

TG2

TG3

LED1

STPB

STPA

SPK

OSC

TEST4

TG1

TG2

TG3

TG4/LED2/STPC

LED1

STPB

STPA

SPK

TEST1 TEST2

OSC

TEST3

W528S03-S12

W528S15-S60

W528SXX

Publication Release Date: Nov 2000

- 3 - Revision A1

PAD DESCRIPTION

PAD NAME

I/O

FUNCTION

TG1

Trigger Input 1

TG2

Trigger Input 2

TG3

Trigger Input 3

TG4/LED2/STPC

I/O

Trigger Input 4 or LED 2 or Stop Signal C

LED1

LED 1

STPB

Stop Signal B

STPA

Stop Signal A

SPK

Current Output for Speaker

Negative Power Supply

Positive Power Supply

OSC

Oscillation Frequency Control

*Test1

Test Pin

*Test2

Test Pin

*Test3

Test Pin

Test4

Test Pin

* These pads only exist in W528S15~60.

W528SXX

- 4 -

BLOCK DIAGRAM

OSC

TIMING

GENERATOR

DATA ROM

TG1

TG2

TG3

LED1

TG4/LED2/STPC

CONTROLLER

COUNTER

REGISTER

STPA

STPB

SYNTHESIZER

ADPCM

CONVERTER

REGISTER

SPK

& SHIFT

SHIFT

D/A

*TEST1

*TEST2

*TEST3

TEST4

* These pins only exist in W528S15~60.

FUNCTIONAL DESCRIPTION

The W528Sxx family provides up to four direct trigger pins, which can be extended to eight or twelve
matrix trigger inputs, up to three stop signal output pins, an LED section control, and powerful
programmable features. The JUMP and LOAD commands and four programmable registers can be
used to program the desired playing mode, stop output signal form, LED flash type, and trigger pin
interrupt modes.

The chip's programmable features can also be used to develop new, customized functions for a wide
variety of innovative applications.

A. Instruction Set Description

This section describes three types of instructions:

Unconditional instructions, which are executed immediately after they are issued.

Conditional instructions, which are executed only when the conditions specified in the instructions

are satisfied.

END instruction, which is used to stop all device activity.

Instructions are programmed by writing LOAD and JUMP commands into the R0, EN, STOP, and
MODE registers.

W528SXX

Publication Release Date: Nov 2000

- 5 - Revision A1

Unconditional Instructions:

1. LOAD (LD) Command:

LD R0, value:

This instruction is used to load a voice-group entry value into register R0. The voice-group entry value
may range from 0 to 255. The initial value of the R0 register is "00000000."

LD EN, operand:

This instruction is used to define the trigger interrupt settings by loading the operand message into
register EN. The initial value of the EN register is "11111111."

a. The operand is an 8-bit value that can be entered in decimal (default) or hexadecimal

(with "0x" as a prefix).

b. EN is an 8-bit register that is used to enable/disable the rising/falling edge of each of the four

trigger inputs.

The 8 bits correspond to the rising/falling edges of the triggers as shown below:

Bit:

TG:

where "nR/F" represents the rising/falling edge of the n-th trigger pin.

c. When any one of the eight bits is set to "1" (default), the corresponding trigger will interrupt the

current state at the edge indicated. When the bits are set to "0," the triggers will be disabled.

d. The voice group entry addresses correspond to the interrupt vectors as follows:

TG:

Group:

EXAMPLE:

The instruction "LD EN, 0x41" is programmed.

EXPLANATION:

a. "41" is a hexadecimal value equal to the binary value "0100 0001."

b. These 8 bits of data represent the following trigger interrupt settings:

4R,

3R,

2R,

1R,

4F,

3F,

2F,

RESULT:

a. When the rising edge of TG3 (3R) is activated, the EN register will cause TG3 to interrupt the
current playing state and jump immediately to voice group 6, the voice group that corresponds
to 3R.

b. When the falling edge of TG1 goes active, the EN register will cause TG1 to interrupt the current

playing state and jump immediately to voice group 0, the voice group that corresponds to 1F.

W528SXX

- 6 -

c. No action will be taken when the other trigger pins are pressed, because the corresponding bits
are set to "0."

LD STOP, operand:

This instruction loads the operand message into the STOP register to set the output levels of the stop
signals. The initial value of the STOP register is "XXXXX111."

a. This register is used to program the output levels of the three STOP signals, STPA, STPB,

and STPC. Only three of the bits in the register are used, as shown below (an "X" indicates
"Don't care"):

Bit:

Stop:

STPC

STPB

STPA

b. When a particular STOP bit is set to "1," The corresponding stop signal will be a high output;

when a bit is set to "0," the corresponding stop signal will be a low output.

EXAMPLE:

The instruction "LD STOP, 0x43" is programmed.

EXPLANATION:

a. "43" is a hexadecimal value equal to a binary value of "0100 0011."

b. These 8 bits of data represent the following settings:

STPC,

STPB,

STPA

RESULT:

a. The STPA and STPB outputs will be high outputs.

b. The STPC signal will be a low output.

c. The sixth bit "1" is a "Don't Care" bit and so has no effect on the stop signal output

settings.

LD MODE, operand:

This instruction is used to select various operating modes. It loads an operand message into the
MODE register to select one mode from each of four pairs of modes, which correspond to bits 4
through 7 of the register (bits 0 to 3 are "Don't Care" bits). The four pairs of modes and the
corresponding bits are as follows:

Bit:

MODE: Flash/DC LED2/STPC TG4/LED2_STPC 45 mS/350

A "1" for one of these bits selects the first of the pair of modes indicated; a "0" selects the second of
the pair. The initial value of the mode register is "1111XXXX."

W528SXX

Publication Release Date: Nov 2000

- 7 - Revision A1

EXAMPLE 1:

The four bits are programmed as "1111," so that the eight bits of the register are as follows (an "X"
indicates a "Don't Care" bit):

Flash/DC, LED2/STPC, TG4/LED2_STPC, 45 mS/350

RESULT:

The mode settings are as follows:

a. Pin 4 (TG4/LED2_STPC) is configured as a trigger pin (TG4), and the LED2/STPC option will

be ignored.

b. The LED is set as a flash type, with a flash frequency of 3 Hz.

c. The debounce time of the trigger inputs is set to 45 mS.

EXAMPLE 2:

The four bits are programmed as "0000," so that the eight bits of the register are as follows (an "X"
indicates a "Don't Care" bit):

Flash/DC, LED2/STPC, TG4/LED2_STPC, 45 mS/350

X, X,

RESULT:

The mode settings are as follows:

a. Pin 4 (TG4/LED2_STPC) is configured as either the LED2 or STPC output (determined by bit 6,

LED2/STPC; see next item).

b. Pin 4 is configured as the STPC output pin.

c. LED will be lit constantly during operation.

d. The debounce time of the trigger inputs is set as 350

2. JUMP (JP) Command:

JP value: Instructs device to jump directly to the voice group corresponding to the value indicated.
The voice group value may range from 0 to 127 (direct jump).

JP R0: Instructs device to jump to whatever voice group is indicated by the value currently stored in
register R0, from 0 to 255 (indirect jump).

W528SXX

- 8 -

Conditional Instructions:

Conditional instructions are executed only when the conditions specified in the instructions hold. The
conditional instructions are listed below. An explanation of the notation used in the instructions follows.

(Note: There are no conditional instructions for LD MODE.)

LD R0, VALUE @LAST: VALUE can be set from 0 to 255.

LD R0, VALUE @TGn_STATUS: VALUE can be set from 0 to 255.

LD EN, OPERAND @LAST: EN - 4R, 3R, 2R, 1R, 4F, 3F, 2F, 1F.

LD STOP, OPERAND @LAST: STOP - X, X, X, X, X, STPC, STPB, STPA.

JP VALUE @LAST: VALUE can be set from 0 to 127.

JP R0 @LAST

JP VALUE @TGn_STATUS: VALUE can be set from 0 to 127

JP R0 @TGn_STATUS

EXPLANATION:

@LAST: At last time of global repeat.

@TGn_STATUS: When the status of the trigger specified (TGn) is in the condition specified,

where the possible triggers and conditions are the following:

TG1_HIGH

TG1_LOW

TG2_HIGH

TG2_LOW

TG3_HIGH

TG3_LOW

TG4_HIGH

TG4_LOW

End Instruction:

END: This command instructs the chip to cease all activity immediately.

B. Program Structure Features and Execution Rules

1. There are eight hardware group entry points and 248 software group entry points, as follows:

Group

8 H/W entries:

TG1F:

TG2F:

TG3F:

TG4F:

TG1R:

W528SXX

Publication Release Date: Nov 2000

- 9 - Revision A1

(Continued)

TG2R:

TG3R:

TG4R:

248 S/W entries:

.
.
.

POI:

.
.
.

254

255

2. Execution begins from group entry and is terminated by END instruction.

3. A H/W trigger interrupt stops the group currently being executed immediately and begins a new
group.

C. Mask Options

There are four mask options for the W528xxx family; the mask options are used to select features that
cannot be programmed through the chip's registers.

The options are the following:

LED flash type (synchronous/alternate)

LED volume-controlled: No/Yes

LED1 section-controlled: Yes/No

LED2: section-controlled/STPC-controlled

D. Speech Equation Description

The format of the speech equations for the W528xxx family is the same as that of the equations used
in the Winbond W52160, W525XX, and W527XX series speech ICs. The following is an example of
the speech equation format:

GR = N

H4+m1*SOUND1_FL+m2*SOUND2_FL+[1FFFF]+...+T4

END

where

W528SXX

- 10 -

GR = N defines the number of global repeats (from 1 to 16);

m1 and m2 define the number of local repeats (from 1 to 7);

SOUND1 and SOUND2 are the *.WAM files of ADPCM converted voice data;

_FL is the section control setting, for which the parameters F and L are as follows:

F: Voice output frequency setting:

0 = 4 KHz, 1 = 4.8 KHz, 2 = 6 KHz, 3 = 8 KHz;

L: LED output setting:

1: ON

0: OFF; and

[1FFFF] is a period of silence of length 1FFFF;

H4, T4: Represent head and tail ADPCM files, respectively.

E. Programmable Power-on Initialization

Whenever the W528xxx is powered on, the program contained in the 32nd voice group will be
executed after the power-on delay (about 160 mS), so the user can write a program into this group to
set the power-on initial state. If the user does not wish to execute a program at power-on, an "END"
instruction should be entered in group 32. The W528xxx power-on initialization process can be
interrupted by trigger inputs.

F. Progamming Examples

This section presents several examples of how the functions of the W528xxx may be programmed.
Customer programs should be written in ASCII code using a text editor; after compiling, the sound
effects resulting from the programs can be tested using a Winbond demo board.

EXAMPLE1: Four playing mode settings:

a. One-Shot Trigger Mode

0: LD EN, 0x01 ; Enable TG1 falling edge input only.

H4 + sound1 + T4

END

The timing diagram for this example is shown below:

TG1:

AUD:

Sound 1

case 1:

case 2:

Sound 1

W528SXX

Publication Release Date: Nov 2000

- 11 - Revision A1

b. Level-Hold Trigger Mode

0: LD EN, 0x11 ; Enable TG1 rising/falling edge input.

H4 + sound1 + T4

JP 0 ; Repeat sound1 until TG1 key released.

4: END ; As soon as TG1 key is released, execute this group entry.

The timing diagram is shown below:

TG1:

AUD:

Stop Immediately

Sound 1

case 1:

case 2:

TG1:

AUD:

Stop Immediately

c. Complete-Cycle Level Hold

0: LD EN, 0x01 ; Enable TG1 falling edge only.

H4 + sound1 + T4

JP 0 @TG1_LOW ; If TG1 status is low level voltage (trigger is pressed), then j ump
to 0;

if not, execute next instruction (END).

END

The timing diagram is shown below:

AUD:

TG1:

Sound 1

case 1:

case 2:

TG1:

AUD:

Sound 1

d. Single-Cycle Level Hold

0: LD EN, 0x11 ; Enable both falling and rising edge input of TG1.

H4 + sound1 + T4

END

4: END ; As soon as TG1 is key released, execute this group entry.

W528SXX

- 12 -

The timing diagram is shown below:

TG1:

AUD:

Sound 1

case 1:

case 2:

TG1:

AUD:

Stop Immediately

EXAMPLE 2: Retriggerable and Non-retriggerable setting

a. Retriggerable:

0: LD EN, 0x01 ; 0x01 = 00000001B, only TG1 falling edge interrupt is enabled.

END

The timing diagram is shown below:

TG1:

AUD:

Sound 1

Restart

Sound 1

b. Non-retriggerable:

0: LD EN, 0x00 ; 0x00 = 00000000B, TG1 falling edge interrupt is disabled.

LD EN, 0x11 ; Recover the TG1 falling and rising edge interrupt is enabled.

END

The timing diagram is shown below:

AUD:

TG1:

Sound 1

W528SXX

Publication Release Date: Nov 2000

- 13 - Revision A1

ABSOLUTE MAXIMUM RATINGS

PARAMETER

SYMBOL

CONDITIONS

RATED VALUE

UNIT

Power Supply

-0.3 to +7.0

Input Voltage

All Inputs

-0.3 to V

+0.3

Storage Temp.

STG

-55 to +150

Operating Temp.

OPR

0 to +70

Note: Exposure to conditions beyond those listed under Absolute Maximum Ratings may adversely affect the life and reliability
of the device.

ELECTRICAL CHARACTERISTICS

= 25

C, V

= 0 V)

PARAMETER

SYM.

CONDITIONS

LIMITS

UNIT

MIN.

TYP. MAX.

Operating Voltage

2.4

5.5

Input Voltage

All Input Pins

-0.3

0.3

0.7 V

Standby Current

DD1

= 3V, No Playing

0.2

DD2

= 5V, No Playing

0.4

Operating Current

OP1

= 3V, No Load

400

OP2

= 5V, No Load

800

Input Current for TG1

TG4

= 3V, V

= 0V

SPK (D/A Full Scale)

= 4.5V, R

= 100

-4.0

-5.0

-6.0

Output Current of STPC

= 3V, V

OUT

= 0.4V

= 3V, V

OUT

= 2.7V

-0.5

LED1

= 3V, V

OUT

= 1V

Output

LED2

= 4.5V, V

OUT

= 1V

Current

STPA

= 3V, V

OUT

= 0.4V

STPB

= 3V, V

OUT

= 2.7V

-1

-3

Oscillation Freq.

OSC

= 3V, R

OSC

= Typ.

2.7

3.3

MHz

= 4.5V, R

OSC

= Typ.

2.7

3.3

Oscillation Freq. Deviation
by Voltage Drop

OSC

F(3V) F(2.4)

F(3V)

7.5

Input Debounce Time

DEB1

OSC

= 3 MHz,

DEB2

SR = 6 KHz

350

Notes:

1. Rosc = 430KOhm for all bodies in W528xxx

W528SXX

- 14 -

TYPICAL APPLICATION CIRCUIT

Speaker

8 ohm

1/4 watt

OSC

Rosc

TG1

TG2

TG3

TG4/LED2/STPC

LED1

STPB

STPA

SPK

C
s

8050 D

39/100 ohm

Notes:
1. In principle, the playing speed determined by R

OSC

should correspond to the sampling rate during the coding phase.

The playing speed may be adjusted by varying R

OSC

, however.

2. Rs is an optional current-dividing resistor. If Rs is added, the resistance should be between 470 and 750

3. Cs is optional.
4. The DC current gain

of transistor 8050 ranges from 120 to 200.

5. All unused trigger pins can be left open because of their internal pull-high resistance.
6. R is used to limit the current on the LED. Case 1: V

= 3V, R = 39

for 1/2/3 LEDs.

Case 2: V

= 4.5V, R = 39

for 2/3 LEDs and R = 100

for 1 LED.

7. No warranty for production.

SUPPLEMENT

A. Power Bouncing

If an irregularity (such as bouncing) occurs in the power supply to V

, as shown in the diagram, the

W528xxx may hang or the logic state machine may lock up. To return the chip to normal operation,
short V

and V

for the W528xxx and then release again.

Power bouncing

Battery

Power on

W528x

Power on reset

W528SXX

Publication Release Date: Nov 2000

- 15 - Revision A1

B. Ttigger Pin Coupling Effect

The trigger pins (TG1

TG4) are built-in 500K

pull high resistor.

If the wire of the input trigger is very close to the speaker wire in the application environment, the
coupling effect will occur. The input voltage of the trigger pin will be unstable, causing the trigger
operation to become abnormal.

An external pull high resistor (Ri) connecting the trigger pin and V

can resolve this problem. The

value of the Ri depends on your application environment.

SPK

TGn

Headquarters

No. 4, Creation Rd. III,
Science-Based Industrial Park,
Hsinchu, Taiwan
TEL: 886-3-5770066
FAX: 886-3-5792697
http://www.winbond.com.tw/
Voice & Fax-on-demand: 886-2-27197006

Taipei Office

11F, No. 115, Sec. 3, Min-Sheng East Rd.,
Taipei, Taiwan
TEL: 886-2-27190505
FAX: 886-2-27197502

Winbond Electronics (H.K.) Ltd.

Rm. 803, World Trade Square, Tower II,
123 Hoi Bun Rd., Kwun Tong,
Kowloon, Hong Kong
TEL: 852-27513100
FAX: 852-27552064

Winbond Electronics North America Corp.
Winbond Memory Lab.
Winbond Microelectronics Corp.
Winbond Systems Lab.

2727 N. First Street, San Jose,
CA 95134, U.S.A.

TEL: 408-9436666
FAX: 408-5441798

Note: All data and specifications are subject to change without notice.

Ð­Ð»ÐµÐºÑ‚Ñ€Ð¾Ð½Ð½Ñ‹Ð¹ ÐºÐ¾Ð¼Ð¿Ð¾Ð½ÐµÐ½Ñ‚: W5280

ÐÐ»ÐµÐºÑ‚Ñ€Ð¾Ð½Ð½Ñ‹Ð¹ ÐºÐ¾Ð¼Ð¿Ð¾Ð½ÐµÐ½Ñ‚: W5280