W53300/W53320

16" Voice/Melody/LCD Controller

(ViewTalk

Series)

Publication Release Date: March 1999

- 1 - Revision A2

GENERAL DESCRIPTION

The W53300/W53320 are a high-performance 4-bit microcontroller (

C) with built-in speech, melody

and 16*48/32*48 LCD driver which includes internal pump circuit. The 4-bit uc core contains dual
clock source, 4-bit ALU, two 8-bit timers, one divider, 20 pin input or output, 7 interrupt sources and
8-level subroutine nesting for interrupt applications. Speech unit can be implemented with Winbond
16-sec Power Speech using ADPCM algorithm. Melody unit provides dual tone output and can store
up to 1k notes. Power reduction mode is also built in to minimize power dissipation. It is ideal for
games, educational toys, remote controllers, watches, clocks and other application products which
incorporate both LCD display and melody.

FEATURES

Operating voltage: 2.4 volt ~ 5.5 volt

Dual clock operating system

RC/Crystal (400 KHz to 4 MHz) for main clock

32.768 KHz crystal oscillation circuit for sub-oscillator

Memory

Program ROM: 16K

Data RAM: 512

4 bit (W53320), 704

4 bit(W53300)

LCD RAM: 384

4 bit (W53320), 192

4 bit (W53300)

20 input/output pins

Ports for input only: 2 ports/8 pins

Input/output ports: 2 ports/8 pins

Port for output only: 1 port /4 pins

Power-down mode

Hold function: no operation (except for oscillator)

Seven types of interrupts

Five internal interrupts (Divider ,Timer 0, Timer 1, Speech, Melody)

Two external interrupts (Port RC, Port RD)

One built-in 14-bit clock frequency divider circuit

Two built-in 8-bit programmable countdown timers

Timer 0: one of two internal clock frequencies (FOSC/4 or FOSC/1024) can be selected

Timer 1: built-in auto-reload function includes internal timer, external event counter from RC.0

or TONE output function (can be used as IR carrier output if main clock is 455 kHz)

Built-in 18/14-bit watchdog timer for system reset by mask code option

Powerful instruction sets

8-level subroutine (including interrupt) nesting

W53300/W53320

- 2 -

LCD driver output

32 com

48 seg (W53320), 16 com

48 seg (W53300)

1/16 or 1/32 duty, 1/5 or 1/7 bias, internal pump circuit option by special register

Speech function

Provides 384 kbits dedicated speech ROM

Direct driving output for speaker

Maximum 256 sections available

Melody function

Provides 22 kbits dedicated melody ROM

Provides 6 kinds of beat, 16 kinds of tempo, and pitch range from G3# to C7

Tremolo, triple frequency and 3 kinds of percussion available

Direct driving output for speaker

Maximum 32 scores available

Mix speech with melody available

Multi-engine controller

PWM output current option

Chip On Board available

W53300/W53320

Publication Release Date: March 1999

- 3 - Revision A2

BLOCK DIAGRAM

LCD DRIVER

STACK

(8 Levels)

(896*4)

Timer 0

(8 Bit)

Timing Generator

SEG0 to SEG47

V2 ~ V6

XIN

XOUT

Timer 1
(8 Bit)

Watch Dog Timer

(18/14 Bit)

VDD2

ALU

ACC

Divider

(14/10 Bit)

X32I

X32O

ROM

(16K*20)

DH1, DH2

COM0 to COM31

RAM

Interrup & Hold
Mode Release

Special Register

HCF

HEF

IEF

EVF

FLAG1

PSR0

MR1

MLDH

PEF

SPCH

FLAG0

LUP2

PM0

LUP3

LUP0 LUP1

LUC

RP0L

RP0M

RP0H

PORT RB

PORT RD

PORT RC

PORT RE

Speech

Dual Tone
Melody

(1K*22 ROM)

(384Kbit ROM)

PORT RA

VLCD PUMP CIRCUIT

MLD_play

MLD_busy

SPC_busy

TONE

TEST

RA0~3

RB0~3

RD0~3

RC0~ 3

RE0 to 3

VDD

LED1
LED2

VSS1

RES

VDDP

PWM1

PWM2

ROSC

VDD3

VSS2

W53300/W53320

- 4 -

PIN DESCRIPTION

SYMBOL

I/O

FUNCTION

XIN

Input pin for oscillator. It can be connected to crystal, or can connect a
resistor to VDD to generate main system clock. Oscillator can be
stopped when SCR.1 is set to logic 1.

XOUT

Output pin for oscillator which is connected to another crystal pin.

X32I

32.768 KHz crystal input pin.

X32O

32.768 KHz crystal output pin.

RA0 ~ RA3

I/O

General Input/Output port specified by PM1 register. If output mode is
selected, PM0 register can be used to specify CMOS/NMOS driving
capability option. Initial state is input mode.

RB0 ~ RB3

I/O

General Input/Output port specified by PM2 register. If output mode is
selected, PM0 register can be used to specify CMOS/NMOS driving
capability option. Initial state is input mode.

RC0 ~ RC3

4-bit schmitt input with internal pull high option specified by PM0
register. RC0 can be used as clock source for Timer 1. Each pin has
an independent interrupt capability specified by PEFL special register.

RD0 ~ RD3

4-bit schmitt input port with internal pull high option specified by PM0
register. Each pin has an independent interrupt capability specified by
PEFH special register.

RE0~RE3/TONE

Output port only. RE3 may use as TONE if bit 0 of MR0 special
register is set to logic 1.

RES

System reset pin with internal pull-high resistor is active low.

TEST

Test pin. No connect for normal use.

ROSC

Connects resistor to VDD to generate speech or melody clock source.

VDDP

Power source for PWM output.

LED1

Synchronous LED1 output while speech play/melody is active.

LED2

Synchronous LED2 output only while speech play is active.

PWM1

Speaker direct driving output 1 while speech or melody is active.

PWM2

Speaker direct driving output 2 while speech or melody is active.

SEG0

SEG47

LCD segment output pins.

COM0

COM31

LCD common signal output pins. The LCD alternating frequency is
fixed at 64Hz. COM16~31 are useless for W53300.

DH1, DH2

Connection terminals for voltage doubler capacitor.

VDD2

Connects a 1uF capacitor to VSS1 to double VDD voltage output if
triple pump option is enabled. Otherwise, VDD2 connects to VDD
directly if double pump option is enabled.

VDD3

O/I

An output if internal pump circuit is enabled. It connects a 1uF
capacitor to VSS. Triple VDD voltage will be output if triple pump
option is enabled. Otherwise, double VDD voltage will be output if
double pump option is enabled.
An input if internal pump voltage is disabled.

W53300/W53320

Publication Release Date: March 1999

- 5 - Revision A2

V2 ~ V5

LCD COM/SEG output driving voltage. If internal shunt resistor is
disabled, external resistors need to be supplied to V2, V3, V4, V5 . A
capacitor is suggestted for stable LCD voltage level.

External variable resistor connects between VDD3 and V6 to adjust
LCD maximun voltage level.

VDD

Microcontroller Positive power supply (+).

VSS1

Negative power supply (-).

VSS2

Negative power supply (-).

ABSOLUTE MAXIMUM RATINGS

PARAMETER

RATING

UNIT

Supply Voltage to Ground Potential

-0.3 to +7.0

Applied Input/Output Voltage

-0.3 to +7.0

Power Dissipation

120

Ambient Operating Temperature

0 to +70

Storage Temperature

-55 to +150

VDD3 Input Voltage

Note: Exposure to conditions beyond those listed under Absolute Maximum Ratings may adversely
affect the life and reliability of the device.

DC CHARACTERISTICS

(VDD

VSS = 3.0V, F

= 1 MHz, Fs = 32.768 KHz, TA = 25

C, LCD on; unless otherwise specified)

PARAMETER

SYM. CONDITIONS

MIN.

TYP.

MAX.

UNIT

Op. Voltage

2.4

5.5

Op. Current

OP1

Dual clock with crystal

250

300

(No Load)

Dual clock with RC type

250

300

Single Clock

100

Halt Mode Current

Iop2

Dual clock with crystal

120

150

(No Load, LCD OFF)

Dual clock with RC type

120

150

Single clock

Input Low Voltage

VSS

0.3*VDD

Input High Voltage

0.7

VDD

Port RA, RB Output Low
Voltage

ABL

IOL = 2.0 mA

0.4

Port RA, RB Output High
Voltage

ABH

IOH = -2.0 mA

2.4

Port RE Sink Current

VOL = 0.4V

Port RE Source Current

VOH = 2.4V

-2

W53300/W53320

- 6 -

PARAMETER

SYM. CONDITIONS

MIN.

TYP.

MAX.

UNIT

Pull-up Resistor

Port RC, RD

100

350

1000

RES Pull-up Resistor

RES

100

500

LED1/LED2 Sink Current

LED

VO=1 volt

PWM1/2 Source Current

SPH

VOL = 2.4V CUR1~0=00

-30

VOL = 2.4V CUR1~0=01

-60

VOL = 2.4V CUR1~0=10

-90

VOL = 2.4V CUR1~0=11

-120

PWM1/2 Sink Current

SPL

VOL = 0.6V CUR1~0=00

VOL = 0.6V CUR1~0=01

VOL = 0.6V CUR1~0=10

VOL = 0.6V CUR1~0=11

120

LCD Supply Current

LCD

No Load, All Seg. ON

COM/SEG On Resistor

Ron

IOH =

10K

VDD2 output voltage

DOB

VLCDEXT=0 & PMPV3B=0

VDD

VLCDEXT=0 & PMPV3B=1

VDD3 output Voltage

TRI

VLCDEXT=0 & PMPV3B=0

VDD

VLCDEXT=0 & PMPV3B=1

VDD3 Input Voltage

LCD

VLCDEXT=1

AC CHARATERISTICS

(VDD

VSS = 3.0V, F

= 1 MHz, Fs = 32.768 KHz, TA = 25

C, LCD on; unless otherwise specified)

PARAMETER

SYM.

CONDITIONS

MIN.

TYP.

MAX.

UNIT

Sub-clock Frequency

Crystal type

32768

Main-clock Frequency

RC type/Crystal type

400K

Op. Frequency

OSC

SCR.0=1

32768

SCR.0=0

400K

Instruction Cycle Time

CYC

One machine cycle

4/F

OSC

Reset Active Width

RAW

FOSC = 32.768 KHz

Interrupt Active Width

IAW

FOSC = 32.768 KHz

Main clock RC frequency

RXIN

RXIN =2.4 M

400K

RXIN =1.2 M

800K

RXIN =910 K

RXIN =160 K

Frequency Deviation of
main-clock FRXIN =1MHz

f(3V) f(2.4V)

f(3V)

ROSC Frequency

ROSC

ROSC =1.2M

3.23

MHz

Frequency Deviation of
FROSC = 3MHz

f(3V) f(2.4V)

f(3V)

Frame frequency

LCD

W53300/W53320

Publication Release Date: March 1999

- 7 - Revision A2

TYPICAL APPLICATION CIRCUIT

RES

XOUT

XIN

DH1

DH2

RC2
RC3

RA0

RA3

Output Signal

RB0
RB1
RB2

COM0

COM31

RB3

RC0
RC1

SEG0

SEG47

RD0

RD1

RD2

RD3

LCD

PANEL

(1/7 Bias
1/32 Duty)

VDD

X32I

X32O

32.768

KHz

0.1 uF

RE0

RE1

RE2

RE3

LED2

LED1

32 COM *48 SEG

W53320

RXIN

VDDP

PWM1

PWM2

ROSC

buzzer
or
speaker

VCC2

VCC1

Note: 1.VCC2 supports high current driving capability to PWM1, PWM2, LED1 and LED2.
2.Triple pump, 1/7 bias
3. Two resistors could be added that one is V6~V5, and another V2~VSS for good display.

VSS

1 uF

VDD2

VDD3

V5
V4

1 uF

0.1 uF

VSS1 VSS2

VCC1

VCC2

W53300/W53320

- 8 -

RES

XOUT

XIN

DH1

DH2

RC2
RC3

RA0

RA3

Output Signal

RB0
RB1
RB2

COM0

COM15

RB3

RC0
RC1

SEG0

SEG47

RD0

RD1

RD2

RD3

LCD

PANEL

(1/5 Bias
1/16 Duty)

VDD

X32I

X32O

32.768

KHz

0.1 uF

RE0

RE1

RE2

RE3

LED2

LED1

16 COM *48 SEG

W53300

RXIN

VDDP

PWM1

PWM2

ROSC

buzzer
or
speaker

VCC2

VCC1

Note: 1.VCC2 supports high current driving capability to PWM1, PWM2, LED1 and LED2.
2.Double pump, 1/5 bias
3.Two resistors could be added that one is V5~V6, anther V2~VSS for good display.

VSS

1 uF

VDD2

VDD3

V5
V4

1 uF

0.1 uF

VSS1 VSS2

VCC1

VCC2

VSS

VCC1

W53300/W53320

Publication Release Date: March 1999

- 9 - Revision A2

Headquarters

No. 4, Creation Rd. III,
Science-Based Industrial Park,
Hsinchu, Taiwan
TEL: 886-3-5770066
FAX: 886-3-5792697
http://www.winbond.com.tw/
Voice & Fax-on-demand: 886-2-7197006

Taipei Office

11F, No. 115, Sec. 3, Min-Sheng East Rd.,
Taipei, Taiwan
TEL: 886-2-7190505
FAX: 886-2-7197502

Winbond Electronics (H.K.) Ltd.

Rm. 803, World Trade Square, Tower II,
123 Hoi Bun Rd., Kwun Tong,
Kowloon, Hong Kong
TEL: 852-27513100
FAX: 852-27552064

Winbond Electronics North America Corp.
Winbond Memory Lab.
Winbond Microelectronics Corp.
Winbond Systems Lab.

2730 Orchard Parkway, San Jose,
CA 95134, U.S.A.
TEL: 1-408-9436666
FAX: 1-408-9436668

Note: All data and specifications are subject to change without notice.

Document Outline

Ð­Ð»ÐµÐºÑ‚Ñ€Ð¾Ð½Ð½Ñ‹Ð¹ ÐºÐ¾Ð¼Ð¿Ð¾Ð½ÐµÐ½Ñ‚: W53300RXIN

Document Outline

ÐÐ»ÐµÐºÑ‚Ñ€Ð¾Ð½Ð½Ñ‹Ð¹ ÐºÐ¾Ð¼Ð¿Ð¾Ð½ÐµÐ½Ñ‚: W53300RXIN