W78L52

8-BIT MICROCONTROLLER

Publication Release Date: January 1999

- 1 -

Revision A2

GENERAL DESCRIPTION

The W78L52 microcontroller supplies a wider frequency and supply voltage range than most 8-bit
microcontrollers on the market. It is compatible with the industry standard 80C52 microcontroller
series. The W78L52 contains four 8-bit bidirectional parallel ports, one extra 4-bit bit-addressable I/O

port (Port 4) and two additional external interrupts (

INT2

, INT3 ), three 16-bit timer/counters, one

watchdog timer and a serial port. These peripherals are supported by a eight-source, two-level
interrupt capability. There are 256 bytes of RAM and an 8K byte mask ROM for application
programs.

The W78L52 microcontroller has two power reduction modes, idle mode and power-down mode, both
of which are software selectable. The idle mode turns off the processor clock but allows for continued
peripheral operation. The power-down mode stops the crystal oscillator for minimum power
consumption. The external clock can be stopped at any time and in any state without affecting the
processor.

FEATURES

Fully static design

Supply voltage of 1.8V to 5.5V

DC-24 MHz operation

256 bytes of on-chip scratchpad RAM

8K bytes of on-chip mask ROM

64K bytes program memory address space

64K bytes data memory address space

Four 8-bit bidirectional ports

Three 16-bit timer/counters

One full duplex serial port

Eight

-source, two-level interrupt capability

One extra 4-bit bit-addressable I/O port

Two additional external interrupts

INT2

/ INT3

Watchdog timer

EMI reduction mode

Built-in power management

Code protection

Packages:

DIP 40: W78L52-24

PLCC 44: W78L52P-24

QFP 44: W78L52F-24

W78L52

- 2 -

PIN CONFIGURATIONS

VDD

P0.0, AD0

P0.1, AD1

P0.2, AD2

P0.3, AD3

P0.4, AD4

P0.5, AD5

P0.6, AD6

P0.7, AD7

EA
ALE

PSEN

P2.5, A13

P2.6, A14

P2.7, A15

P2.0, A8

P2.1, A9

P2.2, A10

P2.3, A11

P2.4, A12

T2, P1.0

40-Pin DIP (W78L52)

P1.2

P1.3

P1.4

P1.5

P1.6

RXD, P3.0
TXD, P3.1

P1.7

RST

INT0, P3.2

INT1, P3.3

T0, P3.4

T1, P3.5

WR, P3.6

RD, P3.7

XTAL1

XTAL2

VSS

T2EX, P1.1

44-Pin PLCC (W78L52P)

44-Pin QFP (W78L52F)

1 44 43 42 41

39
38

30
29

P1.5

P1.6

P1.7

RST

RXD, P3.0

TXD, P3.1

INT0, P3.2

INT1, P3.3

T0, P3.4

T1, P3.5

A
D
3
,
P
0
.
3

T
2
,
P
1
.
0

P
1
.
2

V
D
D

A
D
2
,
P
0
.
2

A
D
1
,
P
0
.
1

A
D
0
,
P
0
.
0

T
2
E
X
,
P
1
.
1

P
1
.
3

P
1
.
4

X
T
A
L
1

V
S
S

P
2
.
4
,
A
1
2

P
2
.
3
,
A
1
1

P
2
.
2
,
A
1
0

P
2
.
1
,
A
9

P
2
.
0
,
A
8

X
T
A
L
2

P
3
.
7
,
/
R
D

P
3
.
6
,
/
W
R

P0.4, AD4

P0.5, AD5

P0.6, AD6

P0.7, AD7

ALE

PSEN
P2.7, A15

P2.6, A14

P2.5, A13

P4.1

P
4
.
0

INT2, P4.3

/
I
N
T
3
,
P
4
.
2

40 39 38 37 36 35

44 43 42 41

33
32

24
23

P0.4, AD4

P0.5, AD5

P0.6, AD6

P0.7, AD7

ALE

PSEN
P2.7, A15

P2.6, A14

P2.5, A13

P1.5

P1.6

P1.7

RST

RXD, P3.0

TXD, P3.1

INT0, P3.2

INT1, P3.3

T0, P3.4

T1, P3.5

X
T
A
L
1

V
S
S

P
2
.
4
,
A
1
2

P
2
.
3
,
A
1
1

P
2
.
2
,
A
1
0

P
2
.
1
,
A
9

P
2
.
0
,
A
8

X
T
A
L
2

P
3
.
7
,
/
R
D

P
3
.
6
,
/
W
R

A
D
3
,
P
0
.
3

T
2
,
P
1
.
0

P
1
.
2

V
D
D

A
D
2
,
P
0
.
2

A
D
1
,
P
0
.
1

A
D
0
,
P
0
.
0

T
2
E
X
,
P
1
.
1

P
1
.
3

P
1
.
4

P
4
.
0

/
I
N
T
3
,
P
4
.
2

P4.1

INT2, P4.3

W78L52

Publication Release Date: January 1999

- 3 -

Revision A2

PIN DESCRIPTION

P0.0

P0.7

Port 0, Bits 0 through 7. Port 0 is a bidirectional I/O port. This port also provides a multiplexed low
order address/data bus during accesses to external memory.

P1.0

P1.7

Port 1, Bits 0 through 7. Port 1 is a bidirectional I/O port with internal pull-ups. Pins P1.0 and P1.1
also serve as T2 (Timer 2 external input) and T2EX (Timer 2 capture/reload trigger), respectively.

P2.0

P2.7

Port 2, Bits 0 through 7. Port 2 is a bidirectional I/O port with internal pull-ups. This port also provides
the upper address bits for accesses to external memory.

P3.0

P3.7

Port 3, Bits 0 through 7. Port 3 is a bidirectional I/O port with internal pull-ups. All bits have alternate
functions, which are described below:

PIN

ALTERNATE FUNCTION

P3.0

RXD Serial Receive Data

P3.1

TXD Serial Transmit Data

P3.2

INT0 External Interrupt 0

P3.3

INT1 External Interrupt 1

P3.4

T0 Timer 0 Input

P3.5

T1 Timer 1 Input

P3.6

WR Data Write Strobe

P3.7

RD Data Read Strobe

P4.0

P4.3

Another bit-addressable bidirectional I/O port P4. P4.3 and P4.2 are alternative function pins. It can

be used as general I/O pins or external interrupt input sources (

INT2

/ INT3 ).

EA
External Address Input, active low. This pin forces the processor to execute out of external ROM.
This pin should be kept low for all W78C32 operations.

RST

Reset Input, active high. This pin resets the processor. It must be kept high for at least two machine
cycles in order to be recognized by the processor.

W78L52

- 4 -

ALE
Address Latch Enable Output, active high. ALE is used to enable the address latch that separates the
address from the data on Port 0. ALE runs at 1/6th of the oscillator frequency. A single ALE pulse is
skipped during external data memory accesses. ALE goes to a high impedance state during reset with
a weak pull-up.

PSEN
Program Store Enable Output, active low.

PSEN

enables the external ROM onto the Port 0

address/data bus during fetch and MOVC operations.

PSEN

goes to a high impedance state during

reset with a weak pull-up.

XTAL1

Crystal 1. This is the crystal oscillator input. This pin may be driven by an external clock.

XTAL2

Crystal 2. This is the crystal oscillator output. It is the inversion of XTAL1.

, V

Power Supplies. These are the chip ground and positive supplies.

BLOCK DIAGRAM

P3.0
~
P3.7

P1.0

P1.7

ALU

Port 0

Latch

Port 1

Latch

Timer

Port

UART

XTAL1

PSEN

ALE

GND

VDD

RST

XTAL2

Oscillator

Interrupt

PSW

Instruction

Decoder

Sequencer

Reset Block

Bus & Clock

Controller

SFR RAM

Address

Power control

256 bytes

RAM & SFR

Stack

Pointer

Addr. Reg.

Incrementor

DPTR

Temp Reg.

ACC

Port 3

Latch

Port 4

Latch

Port

Port 2

Latch

P4.0
~
P4.3

Port

Port
0

Port
2

P2.0
~
P2.7

P0.0
~
P0.7

INT2

INT3

Watchdog

Timer

8K bytes

ROM

W78L52

Publication Release Date: January 1999

- 5 -

Revision A2

FUNCTIONAL DESCRIPTION

The W78L52 architecture consists of a core controller surrounded by various registers, five general
purpose I/O ports, 256 bytes of RAM, three timer/counters, one watchdog timer and a serial port. The
processor supports 111 different opcodes and references both a 64K program address space and a
64 K data storage space.

Timers 0, 1, and 2

Timers 0, 1, and 2 each consist of two 8-bit data registers. These are called TL0 and TH0 for Timer
0, TL1 and TH1 for Timer 1, and TL2 and TH2 for Timer 2. The TCON and TMOD registers provide
control functions for timers 0, 1. The T2CON register provides control functions for Timer 2. RCAP2H
and RCAP2L are used as reload/capture registers for Timer 2. The operations of Timer 0 and Timer
1 are the same as in the W78L51. Timer 2 is a special feature of the W78L52: it is a 16-bit
timer/counter that is configured and controlled by the T2CON register. Like Timers 0 and 1, Timer 2
can operate as either an external event counter or as an internal timer, depending on the setting of
bit C/T2 in T2CON. Timer 2 has three operating modes: capture, auto-reload, and baud rate
generator. The clock speed at capture or auto-reload mode is the same as that of Timers 0 and 1.

Clock

The W78L52 is designed to be used with either a crystal oscillator or an external clock. Internally, the
clock is divided by two before it is used. This makes the W78L52 relatively insensitive to duty cycle
variations in the clock.

Crystal Oscillator

The W78L52 incorporates a built-in crystal oscillator. To make the oscillator work, a crystal must be
connected across pins XTAL1 and XTAL2. In addition, a load capacitor must be connected from each
pin to ground, and a resistor must also be connected from XTAL1 to XTAL2 to provide a DC bias
when the crystal frequency is above 24 MHz.

External Clock

An external clock should be connected to pin XTAL1. Pin XTAL2 should be left unconnected. The
XTAL1 input is a CMOS-type input, as required by the crystal oscillator. As a result, the external clock
signal should have an input one level of greater than 3.5 volts when V

= 5 volts.

Power Management

Idle Mode
The idle mode is entered by setting the IDL bit in the PCON register. In the idle mode, the internal
clock to the processor is stopped. The peripherals and the interrupt logic continue to be clocked. The
processor will exit idle mode when either an interrupt or a reset occurs.

Power-down Mode
When the PD bit of the PCON register is set, the processor enters the power-down mode. In this
mode all of the clocks, including the oscillator are stopped. The only way to exit power-down mode is
by a reset.

Reset

The external RESET signal is sampled at S5P2. To take effect, it must be held high for at least two
machine cycles while the oscillator is running. An internal trigger circuit in the reset line is used to
deglitch the reset line when the W78L52 is used with an external RC network. The reset logic also has

W78L52

- 6 -

a special glitch removal circuit that ignores glitches on the reset line. During reset, the ports are
initialized to FFH, the stack pointer to 07H, PCON (with the exception of bit 4) to 00H, and all of the
other SFR registers except SBUF to 00H. SBUF is not reset.

New Defined Peripheral

In order to be more suitable for I/O, an extra 4-bit bit-addressable port P4 and two external interrupts

INT2

, INT3 have been added to either the PLCC or QFP package. And description follows:

INT2

/ INT3

Two additional external interrupts,

INT2

and INT3 , whose functions are similar to those of external

interrupt 0 and 1 in the standard 80C52. The functions/status of these interrupts are
determined/shown by the bits in the XICON (External Interrupt Control) register. The XICON register
is bit-addressable but is not a standard register in the standard 80C52. Its address is at 0C0H. To
set/clear bits in the XICON register, one can use the "SETB (/CLR) bit" instruction. For example,
"SETB 0C2H" sets the EX2 bit of XICON.

***XICON - external interrupt control (C0H)

PX3

EX3

IE3

IT3

PX2

EX2

IE2

IT2

PX3: External interrupt 3 priority high if set

EX3: External interrupt 3 enable if set

IE3: If IT3 = 1, IE3 is set/cleared automatically by hardware when interrupt is detected/serviced

IT3: External interrupt 3 is falling-edge/low-level triggered when this bit is set/cleared by software

PX2: External interrupt 2 priority high if set

EX2: External interrupt 2 enable if set

IE2: If IT2 = 1, IE2 is set/cleared automatically by hardware when interrupt is detected/serviced

IT2: External interrupt 2 is falling-edge/low-level triggered when this bit is set/cleared by software

Eight-source interrupt informations:

INTERRUPT

SOURCE

VECTOR

ADDRESS

POLLING

SEQUENCE WITHIN

PRIORITY LEVEL

ENABLE

REQUIRED

SETTINGS

INTERRUPT

TYPE

EDGE/LEVEL

External Interrupt 0

03H

0 (highest)

IE.0

TCON.0

Timer/Counter 0

0BH

IE.1

External Interrupt 1

13H

IE.2

TCON.2

Timer/Counter 1

1BH

IE.3

Serial Port

23H

IE.4

Timer/Counter 2

2BH

IE.5

External Interrupt 2

33H

XICON.2

XICON.0

External Interrupt 3

3BH

7 (lowest)

XICON.6

XICON.3

W78L52

Publication Release Date: January 1999

- 7 -

Revision A2

2. PORT4
Another bit-addressable port P4 is also available and only 4 bits (P4<3:0>) can be used. This port
address is located at 0D8H with the same function as that of port P1, except the P4.3 and P4.2 are

alternative function pins. It can be used as general I/O pins or external interrupt input sources (

INT2

INT3 ).

Example: P4

REG

0D8H

MOV

P4, #0AH

; Output data "A" through P4.0

P4.3.

MOV

A, P4

; Read P4 status to Accumulator.

SETB

P4.0

; Set bit P4.0

CLR

P4.1

; Clear bit P4.1

Watchdog Timer

The Watchdog timer is a free-running timer which can be programmed by the user to serve as a
system monitor, a time-base generator or an event timer. It is basically a set of dividers that divide
the system clock. The divider output is selectable and determines the time-out interval. When the
time-out occurs a system reset can also be caused if it is enabled. The main use of the Watchdog
timer is as a system monitor. This is important in real-time control applications. In case of power
glitches or electro-magnetic interference, the processor may begin to execute errant code. If this is
left unchecked the entire system may crash. The watchdog time-out selection will result in different
time-out values depending on the clock speed. The Watchdog timer will de disabled on reset. In
general, software should restart the Watchdog timer to put it into a known state. The control bits that
support the Watchdog timer are discussed below.

Watchdog Timer Control Register

Bit:

ENW

CLRW

WIDL

PS2

PS1

PS0

Mnemonic: WDTC

Address: 8FH

ENW : Enable watch-dog if set.
CLRW: Clear watch-dog timer and prescaler if set. This flag will be cleared automatically
WIDL : If this bit is set, watch-dog is enabled under IDLE mode. If cleared, watch-dog is disabled

under IDLE mode. Default is cleared.

PS2, PS1, PS0: Watch-dog prescaler timer select. Prescaler is selected when set PS2

0 as follows:

PS2 PS1 PS0

PRESCALER SELECT

0 0 0

0 1 0

0 0 1

0 1 1

1 0 0

1 0 1

1 1 0

128

1 1 1

256

W78L52

- 8 -

The time-out period is obtained using the following formula:

OSC

PRESCALER 1000 12 mS

Before Watchdog time-out occurs, the program must clear the 14-bit timer by writing 1 to WDTC.6
(CLRW). After 1 is written to this bit, the 14-bit timer, prescaler and this bit will be reset on the next
instruction cycle. The Watchdog timer is cleared on reset.

OSC

1/12

PRESCALER

14-BIT TIMER

CLEAR

CLRW

EXTERNAL

RESET

INTERNAL

RESET

WIDL

IDLE

ENW

Watchdog Timer Block Diagram

Typical Watchdog time-out period when OSC = 20 MHz

PS2 PS1 PS0

WATCHDOG TIME-OUT PERIOD

0 0 0

19.66 mS

0 1 0

39.32 mS

0 0 1

78.64 mS

0 1 1

157.28 mS

1 0 0

314.57 mS

1 0 1

629.14 mS

1 1 0

1.25 S

1 1 1

2.50 S

Reduce EMI Emission

Because of the on-chip ROM, when a program is running in internal ROM space, the ALE will be
unused. The transition of ALE will cause noise, so it can be turned off to reduce the EMI emission if it
is not needed. Turning off the ALE signal transition only requires setting the bit 0 of the AUXR SFR,
which is located at 08Eh. When ALE is turned off, it will be reactivated when the program accesses
external ROM/RAM data or jumps to execute an external ROM code. The ALE signal will turn off
again after it has been completely accessed or the program returns to internal ROM code space.

AUXR - Auxiliary Register

Bit:

Mnemonic: AUXR

Address: 8Eh

AO:

Turn off ALE signal.

W78L52

Publication Release Date: January 1999

- 9 -

Revision A2

ABSOLUTE MAXIMUM RATINGS

PARAMETER

SYMBOL

MIN.

MAX.

UNIT

DC Power Supply

-0.3

+7.0

Input Voltage

-0.3

+0.3

Operating Temperature

Storage Temperature

-55

+150

Note: Exposure to conditions beyond those listed under Absolute Maximum Ratings may adversely affect the life and reliability of the

device.

DC CHARACTERISTICS

= 0V, T

= 25

C, unless otherwise specified.)

PARAMETER

SYM.

SPECIFICATION

UNIT

TEST CONDITIONS

MIN.

MAX.

Operating Voltage

1.8

5.5

Operating Current

No load V

= 5.5V

No load V

= 2.0V

Idle Current

IDLE

= 5.5V, Fosc = 20 MHz

1.5

= 2.0V, Fosc = 16 MHz

Power Down Current

PWDN

= 5.5V, Fosc = 20 MHz

= 2.0V, Fosc = 16 MHz

Input Current

P1, P2, P3, P4

IN1

-50

+10

= 5.5V

= 0V or V

Input Current

RST

IN2

-10

+300

= 5.5V

0 < V

< V

Input Leakage Current

P0,

-10

+10

= 5.5V

0V < V

< V

Logic 1 to 0 Transition
Current

P1, P2, P3, P4

[*4]

-500

= 5.5V

= 2.0V

Input Low Voltage

IL1

0.8

= 4.5V

P0, P1, P2, P3, P4,

0.5

= 2.0V

Input Low Voltage

IL2

0.8

= 4.5V

RST[*1]

0.3

= 2.0V

W78L52

- 10 -

DC Characteristics, continued

PARAMETER

SYM.

SPECIFICATION

UNIT

TEST CONDITIONS

MIN.

MAX.

Input Low Voltage

IL3

0.8

= 4.5V

XTAL1 [*3]

0.5

= 2.0V

Input High Voltage

IH1

2.0

+0.2

= 5.5V

P0, P1, P2, P3, P4,

1.4

+0.2

= 2.0V

Input High Voltage

IH2

3.5

+0.2

= 5.5V

RST[*1]

1.7

+0.2

= 2.0V

Input High Voltage

IH3

3.5

+0.2

= 5.5V

XTAL1 [*3]

1.6

+0.2

= 2.0V

Output Low Voltage

OL1

0.45

= 4.5V, I

= +2 mA

P1, P2, P3, P4

0.25

= 2.0V, I

= +1 mA

Output Low Voltage

OL2

0.45

= 4.5V, I

= +4 mA

P0, ALE, PSEN [*2]

0.25

= 2.0V, I

= +2 mA

Sink Current

SK1

= 4.5V, Vin = 0.45V

P1, P2, P3, P4

1.8

5.4

= 2.0V, Vin = 0.4V

Sink Current

SK2

= 4.5V, Vin = 0.45V

P0, ALE, PSEN

4.0

= 2.0V, Vin = 0.45V

Output High Voltage

OH1

2.4

= 4.5V, I

= -100

P1, P2, P3, P4

1.4

= 2.0V, I

= -8

Output High Voltage

OH2

2.4

= 4.5V, I

= -400

P0, ALE, PSEN [*2]

1.4

= 2.0V, I

= -200

Source Current

SR1

-100

-250

= 4.5V, Vin = 2.4V

P1, P2, P3, P4

-10

-30

= 2.0V, Vin = 1.4V

Source Current

SR2

-8

-16

= 4.5V, Vin = 2.4V

P0, ALE, PSEN

-1.0

-2.4

= 2.0V, Vin = 1.4V

Notes:

*1. RST pin is a Schmitt trigger input.

*2. P0, ALE and /PSEN are tested in the external access mode.

*3. XTAL1 is a CMOS input.

*4. Pins of P1, P2, P3, P4 can source a transition current when they are being externally driven from 1 to 0.

W78L52

Publication Release Date: January 1999

- 11 -

Revision A2

AC CHARACTERISTICS

The AC specifications are a function of the particular process used to manufacture the part, the
ratings of the I/O buffers, the capacitive load, and the internal routing capacitance. Most of the
specifications can be expressed in terms of multiple input clock periods (T

), and actual parts will

usually experience less than a

20 nS variation. The numbers below represent the performance

expected from a 0.5 micron CMOS process when using 2 and 4 mA output buffers.

Clock Input Waveform

XTAL1

OP,

PARAMETER

SYMBOL

MIN.

TYP.

MAX.

UNIT

NOTES

Operating Speed

MHz

Clock Period

Clock High

Clock Low

Notes:
1. The clock may be stopped indefinitely in either state.
2. The T

specification is used as a reference in other specifications.

3. There are no duty cycle requirements on the XTAL1 input.

Program Fetch Cycle

PARAMETER

SYMBOL

MIN.

TYP.

MAX.

UNIT

NOTES

Address Valid to ALE Low

AAS

1 T

Address Hold from ALE Low

AAH

1 T

1, 4

ALE Low to

PSEN Low

APL

1 T

PSEN Low to Data Valid

PDA

2 T

Data Hold after PSEN High

PDH

1 T

Data Float after PSEN High

PDZ

1 T

ALE Pulse Width

ALW

2 T

PSEN Pulse Width

PSW

3 T

Notes:
1. P0.0

P0.7, P2.0

P2.7 remain stable throughout entire memory cycle.

2. Memory access time is 3 T

3. Data have been latched internally prior to PSEN going high.
4. "

" (due to buffer driving delay and wire loading) is 20 nS.

W78L52

- 12 -

Data Read Cycle

PARAMETER

SYMBOL

MIN.

TYP.

MAX.

UNIT

NOTES

ALE Low to RD Low

DAR

3 T

CP+

1, 2

RD Low to Data Valid

DDA

4 T

Data Hold from RD High

DDH

2 T

Data Float from RD High

DDZ

2 T

RD Pulse Width

DRD

6 T

Notes:

1. Data memory access time is 8 T

2. "

" (due to buffer driving delay and wire loading) is 20 nS.

Data Write Cycle

PARAMETER

SYMBOL

MIN.

TYP.

MAX.

UNIT

ALE Low to WR Low

DAW

3 T

Data Valid to WR Low

DAD

1 T

Data Hold from WR High

DWD

1 T

WR Pulse Width

DWR

6 T

Note: "

" (due to buffer driving delay and wire loading) is 20 nS.

Port Access Cycle

PARAMETER

SYMBOL

MIN.

TYP.

MAX.

UNIT

Port Input Setup to ALE Low

PDS

1 T

Port Input Hold from ALE Low

PDH

Port Output to ALE

PDA

1 T

Note: Ports are read during S5P2, and output data becomes available at the end of S6P2. The timing data are referenced to

ALE, since it provides a convenient reference.

W78L52

Publication Release Date: January 1999

- 15 -

Revision A2

TYPICAL APPLICATION CIRCUITS

Expanded External Program Memory and Crystal

AD0

A10

A11

A12

A13

A14

A15

27512

AD0

74HC373

AD0

XTAL1

XTAL2

RST

INT0

INT1

P1.0

P1.1

P1.2

P1.3

P1.4

P1.5

P1.6

P1.7

39
38
37
36

34
33
32

22
23
24
25
26
27
28

P0.0
P0.1
P0.2
P0.3
P0.4
P0.5
P0.6
P0.7

P2.0
P2.1
P2.2
P2.3
P2.4
P2.5
P2.6
P2.7

PSEN

ALE

TXD

RXD

W78L52

10 u

8.2 K

CRYSTAL

AD1
AD2
AD3
AD4
AD5
AD6

AD7

AD1
AD2
AD3
AD4
AD5
AD6
AD7

GND

A1
A2
A3
A4
A5
A6

A1
A2
A3
A4
A5
A6
A7
A8
A9

AD1
AD2
AD3
AD4
AD5
AD6
AD7

A10
A11
A12
A13
A14
A15

GND

A9
A10
A11

A12

A13
A14
A15

Figure A

CRYSTAL

16 MHz

30P

24 MHz

15P

33 MHz

10P

6.8K

40 MHz

4.7K

Above table shows the reference values for crystal applications.

Note: C1, C2, R components refer to Figure A.

W78L52

- 16 -

Typical Application Circuits, continued

Expanded External Data Memory and Oscillator

10 u

8.2 K

OSCILLATOR

XTAL1

XTAL2

RST

INT0

INT1

T0
T1

P1.0
P1.1
P1.2
P1.3
P1.4
P1.5
P1.6
P1.7

12
13
14
15

1
2
3
4
5
6
7
8

P0.0
P0.1
P0.2
P0.3
P0.4
P0.5
P0.6
P0.7

39
38

37
36
35
34
33
32

P2.0
P2.1
P2.2
P2.3
P2.4
P2.5
P2.6
P2.7

PSEN

ALE

TXD

RXD

W78L52

AD0
AD1
AD2
AD3
AD4
AD5
AD6
AD7

A0
A1
A2
A3
A4
A5
A6
A7

AD7

AD0
AD1
AD2
AD3
AD4
AD5
AD6

3
4
7
8
13
14
17

74HC373

A0
A1
A2
A3
A4
A5
A6
A7

9
8
7
6
5
4
3

A0
A1
A2
A3
A4
A5
A6
A7

AD0
AD1
AD2
AD3
AD4
AD5
AD6
AD7

12
13
15
16
17
18
19

D0
D1
D2
D3
D4
D5
D6
D7

A8
A9
A10
A11
A12
A13
A14

25
24
21
23

A8
A9
A10
A11
A12
A13
A14

GND

21
22
23

24
25
26

27
28

A10
A11
A12
A13

A14

GND

22
27

20256

Figure B

PACKAGE DIMENSIONS

40-pin DIP

Seating Plane

1. Dimension D Max. & S include mold flash or

tie bar burrs.

2. Dimension E1 does not include interlead flash.
3. Dimension D & E1 include mold mismatch and

are determined at the mold parting line.

6. General appearance spec. should be based on

final visual inspection spec.

1.372

1.219

0.054

0.048

Notes:

Symbol

Min.

Nom.

Max.

Nom.

Min.

Dimension in inch

Dimension in mm

0.050

1.27

0.210

5.334

0.010

0.150

0.016

0.155

0.018

0.160

0.022

3.81

0.406

0.254

3.937

0.457

4.064

0.559

0.008

0.120

0.670

0.010

0.130

0.014

0.140

0.203

3.048

0.254

3.302

0.356

3.556

0.540

0.550

0.545

13.72

13.97

13.84

17.01

15.24

14.986

15.494

0.600

0.590

0.610

2.286

2.54

2.794

0.090

0.100

0.110

c
D

2.055

2.070

52.20

52.58

0.090

2.286

0.650

0.630

16.00

16.51

protrusion/intrusion.

4. Dimension B1 does not include dambar

5. Controlling dimension: Inches.

Base Plane

W78L52

Publication Release Date: January 1999

- 17 -

Revision A2

Package Dimensions, continued

44-pin PLCC

Seating Plane

Symbol

Min. Nom.

Max.

Nom.

Min.

Dimension in inch

Dimension in mm

b
c
D

Notes:

on final visual inspection spec.

4. General appearance spec. should be based

3. Controlling dimension: Inches

protrusion/intrusion.

2. Dimension b1 does not include dambar

flash.

1. Dimension D & E do not include interlead

0.020

0.145

0.026

0.016

0.008

0.648

0.590

0.680

0.090

0.150

0.028

0.018

0.010

0.653

0.610

0.690

0.100

0.050

BSC

0.185

0.155

0.032

0.022

0.014

0.658

0.630

0.700

0.110

0.004

0.508

3.683

0.66

0.406

0.203

16.46

14.99

17.27

2.296

3.81

0.711

0.457

0.254

16.59

15.49

17.53

2.54

1.27

4.699

3.937

0.813

0.559

0.356

16.71

16.00

17.78

2.794

0.10

BSC

16.71

16.59

16.46

0.658

0.653

0.648

16.00

15.49

14.99

0.630

0.610

0.590

17.78

17.53

17.27

0.700

0.690

0.680

44-pin QFP

Seating Plane

See Detail F

Detail F

1. Dimension D & E do not include interlead

flash.

2. Dimension b does not include dambar

protrusion/intrusion.

3. Controlling dimension: Millimeter
4. General appearance spec. should be based

on final visual inspection spec.

0.254

0.101

0.010

0.004

Notes:

Symbol

Min.

Nom.

Max.

Nom.

Min.

Dimension in inch

Dimension in mm

b
c
D

A
A

0.006

0.152

---

0.002

0.075

0.01

0.081

0.014

0.087

0.018

1.90

0.25

0.05

2.05

0.35

2.20

0.45

0.390

0.025

0.063

0.003

0.394

0.031

0.398

0.037

9.9

0.80

0.65

1.6

10.00

0.8

10.1

0.95

0.398

0.394

0.390

0.530

0.520

0.510

13.45

13.2

12.95

10.1

10.00

9.9

0.08

0.031

0.01

0.02

0.25

0.5

---

0.025

0.036

0.635

0.952

0.530

0.520

0.510

13.45

13.2

12.95

0.051

0.075

1.295

1.905

W78L52

- 18 -

Headquarters

No. 4, Creation Rd. III,
Science-Based Industrial Park,
Hsinchu, Taiwan
TEL: 886-3-5770066
FAX: 886-3-5792697
http://www.winbond.com.tw/
Voice & Fax-on-demand: 886-2-7197006

Taipei Office

11F, No. 115, Sec. 3, Min-Sheng East Rd.,
Taipei, Taiwan
TEL: 886-2-7190505
FAX: 886-2-7197502

Winbond Electronics (H.K.) Ltd.

Rm. 803, World Trade Square, Tower II,
123 Hoi Bun Rd., Kwun Tong,
Kowloon, Hong Kong
TEL: 852-27513100
FAX: 852-27552064

Winbond Electronics North America Corp.
Winbond Memory Lab.
Winbond Microelectronics Corp.
Winbond Systems Lab.

2727 N. First Street, San Jose,
CA 95134, U.S.A.
TEL: 408-9436666
FAX: 408-5441798

Note: All data and specifications are subject to change without notice.

Ð­Ð»ÐµÐºÑ‚Ñ€Ð¾Ð½Ð½Ñ‹Ð¹ ÐºÐ¾Ð¼Ð¿Ð¾Ð½ÐµÐ½Ñ‚: W78L52

ÐÐ»ÐµÐºÑ‚Ñ€Ð¾Ð½Ð½Ñ‹Ð¹ ÐºÐ¾Ð¼Ð¿Ð¾Ð½ÐµÐ½Ñ‚: W78L52