ChipFind - документация

Электронный компонент: ZL60009TBD

Скачать:  PDF   ZIP

Document Outline

1
Zarlink Semiconductor Inc.
Zarlink, ZL and the Zarlink Semiconductor logo are trademarks of Zarlink Semiconductor Inc.
Copyright 2003, Zarlink Semiconductor Inc. All Rights Reserved.
Features
Data rate up to 200Mbps
1310 - 1550 nm PIN
TO-46 Assembly
TIA with AGC
Single 3.3V supply
Low power consumption
Applications
Sonet OC-3
SDH STM-1
ATM 155Mbps
FDDI, Ethernet
Figure 1 - Pin Diagram
Bottom View
Description
This optical receiver is a 3.3V device which contains a
PIN photodiode and a low noise transimpedance
amplifier assembled in a TO-46 package. It is designed
for OC-3/STM-1 operation. Its optical system is
designed for single mode fiber as well as for multi
mode fiber with a core diameter up to 62.5m.
Reliability Assurance based on Telcordia GR-468-
CORE.
Figure 2 - Functional Schematic
V
CC
GND
Data
Data
October 2003
Ordering Information
ZL60009/TBD
TO-46 with lens
-40
C to +85
C
ZL60009
PIN/Preamp
1300nm-1550nm
Data Sheet
ZL60009
Data Sheet
2
Zarlink Semiconductor Inc.
Operating Conditions: 25C Case Temperature/3.3 V Supply Voltage/Fiber: Single-mode to multi-mode
62.5/125
m fiber
Note 1: P
f
=
2W Peak-Peak power at 10MHz 50% duty cycle
Note 2: P
f
=
100W Peak-Peak average Power at 10MHz 50% duty cycle
Note 3: Measured at 10
-9
BER with a 2
23
-1 PRBS at 155Mbps
Note 4: Measured with STM-1 filter on electrical output i.e. 116 MHz
Note 5: Penalty at 10
-10
BER equals 0.26dB
Note 6: The typical value corresponds to the load prevented by a following limiting amplifier
Optical and Electrical Characteristics
Parameter
Symbol
Min.
Typ.
Max.
Unit
Test Condition
Responsivity, differential
R
13
39
kV/W
=1310nm
R
L
= 100
,
Note 1
Output Voltage amplified,
differential
V
O
270
mV
pp
R
L
= 100
,
Note 2
Bandwidth (3dB
el)
f
c
140
MHz
P
f
= 10W, RL=100
Optical Saturation level,
(average)
0
3
dBm
=1310nm
, Note 3
Noise-Equivalent Power
NEP
-47
dBm
=1310nm, Note 4
Dynamic Range
40
dB
Sensitivity (BER 10
-9
)
S
-37
-36
dBm
=1310nm
, Note 3, 5
Output Resistance (single)
R
O
40
100
Power Dissipation
P
D
72
115
mW
Power Supply Current
I
DD
22
32
mA
Absolute Maximum Ratings
Parameter
Symbol
Min.
Max.
Unit
Supply Voltage
V
CC
-0.5
4.5
V
Storage Temperature
T
stg
-55
125
C
Recommended Operating Conditions
Parameter
Symbol
Min.
Typ.
Max.
Unit
Supply Voltage
V
CC
3
3.3
3.6
V
Output Differential Load, Note 6
R
L
100
1000
Operating Temperature
T
op
-40
85
C
ER
=
ER
=
ZL60009
Data Sheet
3
Zarlink Semiconductor Inc.
Figure 3 - Typical Responsivity Versus Axial Displacement for a Multimode Fiber
Figure 4 - Typical Responsivity Versus Radial Displacement for a Multimode Fiber
Typical Responsivity
Wavelength
Fiber Core/Cladding Diameter Numerical Aperture
10/125m,
NA=0.11
50/125m,
NA=0.20
62.5/125m,
NA=0.275
Differential responsivity
1310 nm
28kV/W
28kV/W
28kV/W
Differential responsivity
1550 nm
34kV/W
34kV/W
34kV/W
z-Axial Displacement of fiber (mm) at r=opt, relative TO-46 lens
R-Radial Displacement of fiber (
m) at z=opt
ZL60009
Data Sheet
4
Zarlink Semiconductor Inc.
Figure 5 - Responsivity Versus Wavelength of Coupled Input Power
Application Guidelines
ESD Handling
The receiver is sensitive to electrostatic discharges. When handling the device, precaution for ESD sensitive
devices should be taken. These precautions include use of ESD protected work area with wrist straps, controlled
work benches, floors etc.
Power Supply Filter
Power Supply decoupling capacitors are recommended for optimal performance of the receiver. A filter is
recommended to minimise power supply noise. see Figure 7.
Figure 6 - Recommended Power Supply Filter
Rel
a
t
i
ve
Resp
o
n
si
vit
y
%
100
50
0
1800
800 900 1000 1100 1200 1300 1400 1500 1600 1700
mm
Wavelength
C
0.1
F
C
10nF
L
10
H
Host
V
CC
PIN /
Preamp
ZL60009
Data Sheet
5
Zarlink Semiconductor Inc.
Data Outputs
Outputs, Data and Data, need to be AC-coupled according to Figure 8. The capacitor determines the low-frequency
cut-off for the system.
For improved sensitivity the optional filter capacitor C
F
should be chosen to constitute a 0.75*bit rate BW filter.
Figure 7 - Required coupling and filter capacitors
ZL60009 output
MC2045
C
10nF
C
10nF
C
F