ChipFind - документация

Электронный компонент: CLV0945A

Скачать:  PDF   ZIP
Digital Radios
Satellite Communications
Pager Basestations
4
7
32
936
0.5-4.5
33
-114
-15
<5
<5
100
50
-40 to 85
Oscillation Frequency Range
Phase Noise @ 10 kHz offset (1 Hz BW, typ.)
Harmonic Suppression (2nd, typ.)
Tuning Voltage
Tuning Sensitivity (avg.)
Power Output
Load Impedance
Input Capacitance (max.)
Pushing
Pulling (14 dB Return Loss, Any Phase)
Operating Temperature Range
Package Style
MINI-14S
MHz
dBc/Hz
dBc
Vdc
MHz/V
dBm
pF
MHz/V
MHz
C
Vdc
mA
Supply Voltage (Vcc, nom.)
Supply Current (Icc, typ.)
All specifications are typical unless otherwise noted and subject to change without notice.
PHASE NOISE (1 Hz BW, typical)
Z-Communications, Inc.
All rights reserved
Page 1
VOLTAGE CONTROLLED OSCILLATOR
FEATURES
APPLICATIONS
PERFORMANCE SPECIFICATIONS
VALUE
UNITS
POWER SUPPLY REQUIREMENTS
APPLICATION NOTES
936 953
-
MHz
Frequency Range:
Tuning Voltage:
0.5-4.5 Vdc
- Style Package
MINI-14S


A1
Rev
AN-100/1 : Mounting and Grounding of VCOs
AN-102 : Proper Output Loading of VCOs
AN-107 : How to Solder Z-COMM VCOs
NOTES:
9939 Via Pasar San Diego, CA 92126
TEL (858) 621-2700 FAX (858) 621-2722
- 953
(f) (dBc/Hz)
840
860
880
900
920
940
960
980
1000
1020
0
0.5
1
1.5
2
2.5
3
3.5
4
4.5
0
1
2
3
4
5
6
7
854
873
889
905
921
937
954
971
985
998
LOW COST - HIGH PERFORMANCE
VOLTAGE CONTROLLED OSCILLATOR
Z-Communications, Inc.
Page 2
Printed in the U.S.A.
TUNING CURVE, typ.
POWER CURVE, typ.
PAGE 2
PHYSICAL DIMENSIONS
c
c
c
85
-40
25
c
25
TABS RANGE:
SEE NOTE 5.
(4 PLACES)
DETAIL A
MINI-14S
415-0060 REV. D
(DRAWING NOT TO SCALE)
SEE DETAIL 'A'
0.475
0.000
0.025
0.500
0.415
0.315
0.215
0.090
0.
20
0
0
.
285
0
.
385
0.
5
0
0
0.090
0.215
0.315
0.415
0.
42
0
0.
32
0
0.
47
5
0.
50
0
0.
000
0.
0
2
5
0.
22
0
GROUND PLANE SOLDER PLATED
BOTTOM VIEW
P1
P3
P2
P1=VT
P2=RF OUT
P3=Vcc
NOTES:
THE INSIDE RADIUS OF ALL 14 HALF HOLES
AT THE PERIMETER OF THE BOARD ARE
PLATED TO PROVIDE A SURFACE FOR THE
ATTACHMENT OF THE VCO TO A PCB
IN 11 LOCATIONS, WITH 3 PADS BEING
USED FOR ELECTROMECHANICAL INTERFACE.
2. THE SURFACE OF THE SHIELD IS TIN PLATED
AND MAY BE SOLDERED TO. THE SHIELD'S
3. THE GROUND PLANE IS GROUND AND ATTACHES
TO A GROUND TRACK ON THE UPPER SIDE OF
THE BOARD AS WELL AS THE SHIELD BY PTH.
1.
14 SOLDER LOCATIONS REQUIRED.
BASE METAL IS COLD ROLLED STEEL.
.XXX= .010
TOLERANCES
4. UNLESS OTHERWISE NOTED ALL DIMENSIONS
ARE IN INCHES.
5. UNLESS OTHERWISE NOTED ALL TOLERANCES
ARE AS FOLLOWS:
.030
SEE NOTE 3
TYPICAL OF ALL PADS
.026
.031
.052
.114
.065
.220
.034
0.000
-.
00
5
.
465
.070 TYP
.150
TYP
TUNING VOLTAGE (Vdc)
FREQUENCY (MHz)
POWER OUTPUT (dBm)
FREQUENCY (MHz)