-150
-140
-130
-120
-110
-100
-90
-80
-70
-60
1 E+3
10 E+3
100 E+3
CLV1630A-LF
Digital Radios
Basestations
Mobile Communications
5
23
3.52.5
1593
0.5-4.5
31
-111
-15
<1
<1
50
50
-40 to 85
Oscillation Frequency Range
Phase Noise @ 10 kHz offset (1 Hz BW, typ.)
Harmonic Suppression (2nd, typ.)
Tuning Voltage
Tuning Sensitivity (avg.)
Power Output
Load Impedance
Input Capacitance (max.)
Pushing
Pulling (14 dB Return Loss, Any Phase)
Operating Temperature Range
Package Style
MINI-16-L
MHz
dBc/Hz
dBc
Vdc
MHz/V
dBm
pF
MHz/V
MHz
C
Vdc
mA
Supply Voltage (Vcc, nom.)
Supply Current (Icc, typ.)
All specifications are typical unless otherwise noted and subject to change without notice.
PHASE NOISE (1 Hz BW, typical)
Z-Communications, Inc.
All rights reserved
Page 1
VOLTAGE CONTROLLED OSCILLATOR
FEATURES
APPLICATIONS
PERFORMANCE SPECIFICATIONS
VALUE
UNITS
POWER SUPPLY REQUIREMENTS
APPLICATION NOTES
1593 1654
-
MHz
Frequency Range:
Tuning Voltage:
0.5-4.5 Vdc
- Style Package
MINI-16-L
A1
Rev
AN-100/1 : Mounting and Grounding of VCOs
AN-102 : Proper Output Loading of VCOs
AN-107 : How to Solder Z-COMM VCOs
NOTES:
9939 Via Pasar San Diego, CA 92126
TEL (858) 621-2700 FAX (858) 621-2722
- 1654
OFFSET (Hz)
(f) (dBc/Hz)
1500
1525
1550
1575
1600
1625
1650
1675
1700
1725
0
0.5
1
1.5
2
2.5
3
3.5
4
4.5
0
1
2
3
4
5
6
1545
1563
1579
1595
1611
1625
1642
1658
1675
1693
LOW COST - HIGH PERFORMANCE
VOLTAGE CONTROLLED OSCILLATOR
Z-Communications, Inc.
Page 2
Printed in the U.S.A.
CLV1630A-LF
TUNING CURVE, typ.
POWER CURVE, typ.
PAGE 2
PHYSICAL DIMENSIONS
c
c
c
85
-40
25
c
25
0.475
0.000
0.025
0.500
0.405
0.305
0.205
0.105
0.
18
5
0.
28
5
0.
38
5
0.
500
0.115
0.215
0.315
0.415
0.
420
0
.
320
0.
475
0.
500
0.
000
0.
02
5
0
.
220
GROUND PLANE SOLDER PLATED
BOTTOM VIEW
P1
P3
P2
.037
SEE NOTE 3
TYPICAL OF ALL PADS
.026
.031
.052
.114
.070
0.
08
5
0.
115
TABS RANGE:
SEE NOTE 5.
(4 PLACES)
DETAIL A
P1=VT
P2=RF OUT
P3=Vcc
.130
.034
0.000
-
.
005
.4
65
.070 TYP
.150
TYP
MINI-16-L
415-0061 REV. D
(DRAWING NOT TO SCALE)
SEE DETAIL 'A'
NOTES:
THE INSIDE RADIUS OF ALL 16 HALF HOLES
AT THE PERIMETER OF THE BOARD ARE
PLATED TO PROVIDE A SURFACE FOR THE
ATTACHMENT OF THE VCO TO A PCB,
IN 13 LOCATIONS, WITH 3 PADS BEING
USED FOR ELECTROMECHANICAL INTERFACE.
2. THE SURFACE OF THE SHIELD IS TIN PLATED
AND MAY BE SOLDERED TO. THE SHIELD'S
3. THE GROUND PLANE IS GROUND AND ATTACHES
TO A GROUND TRACK ON THE UPPER SIDE OF
THE BOARD AS WELL AS THE SHIELD BY PTH.
1.
16 SOLDER LOCATIONS REQUIRED.
BASE METAL IS COLD ROLLED STEEL.
.XXX= .010
TOLERANCES
4. UNLESS OTHERWISE NOTED ALL DIMENSIONS
ARE IN INCHES.
5. UNLESS OTHERWISE NOTED ALL TOLERANCES
ARE AS FOLLOWS:
TUNING VOLTAGE (Vdc)
FREQUENCY (MHz)
POWER OUTPUT (dBm)
FREQUENCY (MHz)
PDF 
ZIP