ChipFind - документация

Электронный компонент: AZ2500P2-1A5DE

Скачать:  PDF   ZIP
GENERAL DATA
Life Expectancy
Minimum operations
Mechanical
1 x 10
7
Electrical
1 x 10
5
at 40 A 250 VAC Res.
Set and Reset
Pulse Duration
50 ms minimum
Set Time (typical)
20 ms at nominal coil voltage
Reset Time (typical)
20 ms at nominal coil voltage
Dielectric Strength
4000 Vrms coil to contact
(at sea level for 1 min.) 1500 Vrms between open contacts
Insulation
1000 megohms min. at 20C, 500 VDC,
Resistance
50% RH
Creepage Distance
8 mm
Ambient Temperature
At nominal coil voltage
Operating
-40C (-40F) to 70C (158F)
Storage
-40C (-40F) to 105C (221F)
Vibration
0.062" DA at 1055 Hz
Shock
Operating
20 g, 11 ms,
1
/
2
sine (no false operation)
Non-Operating 100 g, 11 ms,
1
/
2
sine (no damage)
Enclosure
P.B.T. polyester
Terminals
Tinned copper alloy
P. C. (coil), heavy tabs (power)
Max. Solder Temp.
270C (518F)
Max. Solder Time
5 seconds
Weight
33 grams
NOTES
1. All values at 20C (68F).
2. Relay may pull in with less than "Must Operate" value.
3. Specifications subject to change without notice.
4. Allow suitable slack on leads when wiring, and do not subject the
terminals to excessive force.
AZ2500
11/10/03W
50 AMP LATCHING
POWER RELAY
FEATURES
Low cost
50 Amp switching
Heavy loads to 12500 VA
4 kV dielectric
Epoxy sealed construction available
UL, CUR file E43203
CONTACTS
Arrangement
SPST (1 Form A)
Ratings
Resistive load:
Max. switched power: 12500 VA
Max. switched current: 50 A
Max. switched voltage: 400 VAC
Rated Load
UL, CUR
50 A at 250 VAC, 10k cycles, General Use
40 A at 250 VAC, 100k cycles, General Use
Material
Silver cadmium oxide
Resistance
< 50 milliohms initially
(24 V, 1 A voltage drop method)
COIL
Power
At Pickup Voltage
486 mW single coil
(typical)
980 mW dual coil
Temperature
Max. 105C (2221F)
AZ2500
11/10/03W
Dimensions in inches with metric equivalents in parentheses. Tolerance: .010"
RELAY ORDERING DATA
COIL SPECIFICATIONS -Standard Single Coil - Termination Style 1
ORDER NUMBER*
Nominal Coil
Must Operate
Max. Continuous
Coil Resistance
Unsealed
Sealed
VDC
VDC
VDC
10%
5
4.0
6.5
24
AZ2500P11A5D
AZ2500P1-1A5DE
6
4.8
7.8
35
AZ2500P11A6D
AZ2500P1-1A6DE
9
7.2
11.7
80
AZ2500P11A9D
AZ2500P1-1A9DE
12
9.6
15.6
145
AZ2500P11A12D
AZ2500P1-1A12DE
24
19.2
31.2
575
AZ2500P11A24D
AZ2500P1-1A24DE
48
38.4
62.4
2270
AZ2500P11A48D
AZ2500P1-1A48DE
* Add suffix "K" for Coil Termination Style 2
COIL SPECIFICATIONS -Standard Dual Coil
ORDER NUMBER
Nominal Coil
Must Operate
Max. Continuous
Coil Resistance
Unsealed
Sealed
VDC
VDC
VDC
10%
5
4.0
6.5
12
AZ2500P21A5D
AZ2500P2-1A5DE
6
4.8
7.8
17.5
AZ2500P21A6D
AZ2500P2-1A6DE
9
7.2
11.7
40
AZ2500P21A9D
AZ2500P2-1A9DE
12
9.6
15.6
72
AZ2500P21A12D
AZ2500P2-1A12DE
24
19.2
31.2
285
AZ2500P21A24D
AZ2500P2-1A24DE
48
38.4
62.4
1135
AZ2500P21A48D
AZ2500P2-1A48DE
* Add suffix "K" for Coil Termination Style 2. NOTE: Relays may be ordered with twisted copper wire terminations (Styles A-K) as shown below.
Contact factory for ordering information.
MECHANICAL DATA
1.20 MAX
[30.25]
.142
[3.60]
.138
[3.50]
.640MAX
[16.25]
.364MAX
[9.25]
.039
.346
[8.80]
.315
.031
WIRING DIAGRAM
3-.047
[1.20]
.850
[21.59]
.751
[19.08]
1.000
[25.4]
1.51 MAX
[38.25]
PC BOARD LAYOUT
.115
[2.93]
.105
[2.67]
.105
[2.67]
.115
[2.93]
3-.047
[1.20]
1.000
[25.4]
.751
[19.08]
.200
[5.08]
.200
[5.08]
.115
[2.93]
.751
[19.08]
.850
[21.59]
1.000
[25.4]
.105
[2.67]
AZ2500P1-2
"K"
AZ2500P1-1
AZ2500P2
4-.047
[1.20]
AZ2500P1-1
AZ2500P1-2
"K"
AZ2500P2
0.025X0.025
[0.64X0.64]
Reset polarity
Set polarity
Set polarity
Reset polarity
Set coil
(Contact close)
(Contact open)
Reset coil
+
+
-
-
-
-
+
+
+
+
-
AZ2500
11/10/03W
Weld style of twisted copper wire (A to K)
G
D
H
A
E
K
F
B
C
Notes: Weld figures for AZ2500
with twisted copper wire. Please
show welding style (A to K) and
the length of wires when ordering.
Please note the length of each
wire from left to right if the length
is different.