ZETTLER
electronics GmbH
Fax +49 89 800 97 200 www.ZETTLERelectronics.com
office@ZETTLERelectronics.com
0
97
800
89
+49
Tel.
Germany
Puchheim,
D-82178
Junkersstrasse 3,
2004-07-20
AZ2800
GENERAL DATA
Life Expectancy
Minimum operations
Mechanical
5 x 10
7
Electrical
1 x 10
5
at 30 A 120 VAC Res. N.O.
Operate Time
15 ms typical
25 ms maximum with bounce
Release Time
10 ms typical
25 ms maximum with bounce
(with no coil suppression)
Dielectric Strength
1500 Vrms contact to contact
(at sea level for 1 min.) 4000 Vrms contact to coil
2000 Vrms between contact sets
Insulation Resistance
10
9
ohms minimum at 500 VDC
Dropout
DC: Greater than 10%of nominal coil voltage
AC: Greater than 20%of nominal coil voltage
Ambient Temperature
At nominal coil voltage
Operating
DC: -40C (-40F) to 85C (185F)
AC: -40C (-40F) to 65C (149F)
Storage
-40C (-40F) to 105C (221F)
Vibration
0.062" (1.5 mm) DA at 1055 Hz
Shock
Operational, 10 g for 11 ms
1
/
2
sine pulse
(no contact opening > 100usec)
Non-destructive, 100 g for 11 ms
1
/
2
sine pulse
Enclosure
P.B.T. polyester
Terminals
Quick connect tabs
Note: Allow suitable slack on leads when wiring,
and do not subject the terminals to excessive
force
Max. Solvent Temp.
80C (176F)
Max. Immersion Time
30 seconds
Weight
86 grams
Packing unit in pcs
20 per plastic tray / 100 per carton box
COIL
Power
At Pickup Voltage
DC: 0.925 W
(typical)
AC: 2.6 VA
Max. Continuous
DC: 5.0 W at 20C (68F)
Dissipation
AC: 7.0 VA at 20C (68F)
Temperature Rise
DC: 48C (86F) at nominal coil voltage
AC: 68 C (122F) at nominal coil voltage
Temperature
Max. 155C (311F)
30 AMP MINIATURE
POWER RELAY
FEATURES
30 Amp switching capability
DPST-NO and DPDT configuration
Meets 8 mm creepage, 4 kV dielectric
Class F construction
Epoxy sealed version available
UL, CUR file E44211, VDE pending
NOTES
1. All values at 20C (68F).
2. Relay may pull in with less than "Must Operate" value.
3. Specifications subject to change without notice.
CONTACTS
Arrangement
DPST (2 Form A)
DPDT (2 Form C)
Ratings
Resistive load:
Max. switched power: 560 W or 8310 VA
Max. switched current: 30 A (N.O.), 3 A (N.C.)
Max. switched voltage: 600 VAC or 30 VDC*
* Note: If switching voltage is greater than 30VDC,
special precautions must be taken.
Please contact the factory.
Rated Load
UL, CUR
30 A at 277 VAC General Use, 100k cycles
N.O.
1 Hp at 120 VAC, 100k cycles
2.5 Hp at 240 VAC, 100k cycles
110 LRA / 25.3 FLA at 240 VAC (DC coils only),
30k cycles
UL, CUR
3 A at 277 VAC General Use, 100k cycles
N.C.
Material
Silver cadmium oxide or silver tin oxide
Resistance
<50 milliohms initially
(6 V, 1 A voltage drop method)
MECHANICAL DATA
2004-07-20
ZETTLER
electronics GmbH
Fax +49 89 800 97 200 www.ZETTLERelectronics.com
office@ZETTLERelectronics.com
0
97
800
89
+49
Tel.
Germany
Puchheim,
D-82178
Junkersstrasse 3,
AZ2800
MECHANICAL DATA
.58
0
1
3
4
7
8
2
6
0
4
8
2
6
2 FORM C
1
VIEWED TOWARD TERMINALS
2 FORM A
1.36
[34.5]
1.04
[26.4]
[8.0]
2.35
8 x .032
[.8]
2.69
[68.4]
[41.1]
[59.7]
WIRING DIAGRAM
[14.8]
.31
1.62
[3.8]
.15
.63
[16.0]
8 x .45
[11.4]
2 x DIM "A"
DIM. "A" = .250 x .032 [6.3 x 0.8] - STANDARD
DIM. "A" = .187 x .020 [4.8 x 0.5] - SUFFIX "K"
[3.3]
.13
[4.6]
.18
[6.3]
6 x .250
[25.4]
1.00
Dimensions in inches with metric equivalents in parentheses. Tolerance: .010"
RELAY ORDERING DATA
COIL SPECIFICATIONS DC Coil
Nominal Coil
Must Operate
Max. Continuous
Nominal Current
Coil Resistance
ORDER NUMBER*
VDC
VDC
VDC
mA 10%
Ohm 10%
6
4.5
10.5
272.0
22
AZ28002C6D
12
9.0
20.7
140.0
86
AZ28002C12D
24
18.0
41.8
68.5
350
AZ28002C24D
48
36.0
83.4
34.5
1,390
AZ28002C48D
110
82.5
190.5
15.2
7,255
AZ28002C110D
COIL SPECIFICATIONS AC Coil
50 Hz
Nominal Coil
Must Operate
Max. Continuous
Nominal Current
Coil Resistance
ORDER NUMBER*
VAC
VAC
VAC
mA 10%
Ohm 10%
12
9.6
15.6
340.0
8
AZ28002C12A5
24
19.2
31.2
166.0
45
AZ28002C24A5
120
96.0
156.0
33.3
1,125
AZ28002C120A5
220
176.0
286.0
18.2
3,800
AZ28002C220A5
240
192.0
312.0
16.7
4,500
AZ28002C240A5
277
221.6
360.1
14.4
6,000
AZ28002C277A5
* Substitute "2A" in place of "2C" to indicate 2 Form A contacts. Add suffix "E" to "2A" or "2C" to indicate silver tin oxide contacts.
Add suffix "E" at the end of part number for sealed version. Add suffix "K" for 0.187 x 0.020 [4.8 x 0.5] coil terminals.
PDF 
ZIP