CONTACTS
Arrangement
SPST (1 Form A)
SPDT (1 Form C)
Ratings
Resistive load:
Max. switched power: 300 W or 2500 VA
Max. switched current: 10 A
Max. switched voltage: 150* VDC or 380 VAC
*
Note: If switching voltage is greater than 30 VDC, special
precautions must be taken. Please contact the factory.
Rated Load
UL, CUR
TV-5 120 AC
10 A 277 VAC general use
10 A 30 VDC resistive
1
/
3
HP 250 VAC
1
/
4
HP 125 VAC N.O.
TV
10 A 250 VAC, 30 VDC resistive, 100k cycles
Material
Silver cadmium oxide
Resistance
< 50 milliohms initially
(24 V, 1 A voltage drop method)
COIL
Power
At Pickup Voltage
257 mW
(typical)
Max. Continuous
Dissipation
1.9 W at 20C (68F) ambient
Temperature Rise
34C (61F) nominal coil voltage
Temperature
Max. 130C (266F)
NOTES
1. All values at 20C (68F).
2. Relay may pull in with less than "Must Operate" value.
3. Specifications subject to change without notice.
AZ697
8/1/02W
10 AMP MINIATURE
POWER RELAY
FEATURES
Dielectric strength 5000 Vrms
Low cost
Epoxy sealed version available
10 Amp switching -- single pole contacts
UL TV-5
Isolation spacing greater than 8mm
UL Class B insulation system
UL, CUR file E44211; TV file R9659061
GENERAL DATA
Life Expectancy
Minimum operations
Mechanical
1 x 10
7
Electrical
1 x 10
5
at 10 A 240 VAC Res.
Operate Time (typical)
8 ms at nominal coil voltage
Release Time (typical)
5 ms at nominal coil voltage
(with no coil suppression)
Dielectric Strength
5000 Vrms coil to contact
(at sea level for 1 min.) 1000 Vrms between open contacts
Insulation
1000 megohms min. at 20C, 500 VDC
Resistance
50% RH
Dropout
Greater than 10% of nominal coil voltage
Ambient Temperature
At nominal coil voltage
Operating
-40C (-40F) to 90C (194F)
Storage
-40C (-40F) to 130C (266F)
Vibration
0.062" DA at 1055 Hz
Shock
10 g
Enclosure
P.B.T. polyester
Terminals
Tinned copper alloy, P. C.
Max. Solder Temp.
270C (518F)
Max. Solder Time
5 seconds
Max. Solvent Temp.
80C (176F)
Max. Immersion Time
30 seconds
Weight
18 grams
AZ697
8/1/02W
MECHANICAL DATA
Form A and C
Form A
WIRING DIAGRAM
PC BOARD LAYOUT
Form C
3
4
5
1
3
4
5
1
2
1.14
(29)
.160
.015
(4.2
.4)
1.02
(25.9)
.51
(13)
.015
(0.38)
.08
(2.1)
(Form C only)
.649
(16.5)
.138
(3.5)
.138
(3.5)
.295 (7.5)
.05 DIA. (1.3)
(4 places Form A)
(5 places Form C)
Terminal No.
1,2,3,5
4
Dimensions Tol.: 0.005 (0.13)
0.018 (0.457) x 0.038 (0.965)
0.011 (0.279) x 0.038 (0.965)
Viewed toward terminals
Viewed toward terminals
.125
(3.2)
DIA
.414
(10.5)
1.22
(30.9)
.500
(12.7)
1.28
(32.5)
.354
(9.0)
.177
(4.5)
MAX.
.366
(9.3)
.059
(1.5)
DIA
.276
(7.0)
.295
(7.5)
.792
(20.1)
.118
(3.0)
1.217
(30.9)
1.004
(26.5)
.138
(3.5)
RETAINING
CLIP
.158
(4.0)
ST482-U1
Dimensions in inches with metric equivalents in parentheses. Tolerance: .010"
RELAY ORDERING DATA
COIL SPECIFICATIONS
ORDER NUMBER*
Nominal Coil
Must Operate
Max. Continuous
Coil
Form A
Form C
VDC
VDC
VDC
Resistance
(SPST)
(SPDT)
3
2.1
5.7
17 10%
AZ6971A3D
AZ6971C3D
5
3.5
9.4
47 10%
AZ6971A5D
AZ6971C5D
6
4.2
11.4
68 10%
AZ6971A6D
AZ6971C6D
9
6.3
17.4
160 10%
AZ6971A9D
AZ6971C9D
12
8.4
22.8
275 10%
AZ6971A12D
AZ6971C12D
18
12.6
27.9
650 10%
AZ6971A18D
AZ6971C18D
24
16.8
45.7
1100 15%
AZ6971A24D
AZ6971C24D
48
33.6
89.0
4170 15%
AZ6971A48D
AZ6971C48D
60
42.0
115.3
7000 15%
AZ6971A60D
AZ6971C60D
110**
79.3
170.5
22900 15%
AZ6971A110D
AZ6971C110D
*Add suffix "E" for epoxy sealed version. **110V coil not TV approved.
HARDWARE ORDERING DATA
DESCRIPTION
ORDER NUMBER
DESCRIPTION
ORDER NUMBER
Socket
ST482U1
Retainer
ST4822
HARDWARE
ST482-2
PDF 
ZIP