16 A SPDT MINIATURE
POWER RELAY
FEATURES
Dielectric strength 5000 Vrms
Low cost
Epoxy sealed version available
16 Amp switching
Isolation spacing greater than 10 mm
Reinforced insulation, EN 60730-1 (VDE 0631, part 1),
EN 60335-1 (VDE 0700, part 1)
UL, CUR file E44211
VDE 40006031
ZETTLER
electronics GmbH
Fax +49 89 800 97 200 www.ZETTLERelectronics.com
office@ZETTLERelectronics.com
0
97
800
89
+49
Tel.
Germany
Puchheim,
D-82178
Junkersstrasse 3,
2004-09-27
AZ762
GENERAL DATA
Life Expectancy
Minimum operations
Mechanical
1 x 10
7
Electrical
1 x 10
5
at 16 A 250 VAC Res.
Operate Time (typical)
7 ms at nominal coil voltage
Release Time (typical)
3 ms at nominal coil voltage
(with no coil suppression)
Dielectric Strength
5000 Vrms coil to contact
(at sea level for 1 min.) 1000 Vrms between open contacts
Insulation
1000 megohms min. at 20C
Resistance
500 VDC 50% RH
Insulation
C250
(according to
Overvoltage category: III
DIN VDE 0110,
Pollution degree: 3
IEC 60664-1)
Nominal voltage: 250 VAC
Dropout
Greater than 10% of nominal coil voltage
Ambient Temperature
At nominal coil voltage
Operating
-40C (-40F) to 85C (185F)
Storage
-40C (-40F) to 105C (221F)
Vibration
0.062" (1.5 mm) DA at 1055 Hz
Shock
10 g
Enclosure
P.B.T. polyester
Terminals
Tinned copper alloy, P.C.
Max. Solder Temp.
270C (518F)
Max. Solder Time
5 seconds
Max. Solvent Temp.
80C (176F)
Max. Immersion Time
30 Seconds
Weight
14 grams
Packing unit in pcs
20 per plastic tube / 1000 per carton box
CONTACTS
Arrangement
SPDT (1 Form C)
SPST (1 Form A, 1 Form B)
Ratings
Resistive load:
Max. switched power: 480 W or 4432 VA
Max. switched current: 16 A
Max. switched voltage: 150 VDC* or 440 VAC
*
Note: If switching voltage is greater than 30 VDC,
special precautions must be taken.
Please contact the factory.
Rated Load
UL, CUR
16 A at 277 VAC resistive, 100k cycles [3]
16 A at 277 VAC resistive, 50k cycles [1]
1 HP at 250 VAC (1 Form A) [1]
1
/
2
HP at 125 VAC (1 Form A) [1]
TV-5 at 125 VAC (1 Form A) [1]
16 A at 277 VAC resistive, 75k cycles [2]
B300 Pilot Duty [2]
R300 Pilot Duty [2]
VDE
16 A at 250 VAC resistive, [1] [2] and [3]
9 A at 250 VAC, inductive (Form A) [1] [2] and [3]
Material
Silver cadmium oxide [1] or silver tin oxide [2]
or silver nickel [3]. Gold plating available
Resistance
< 50 milliohms initially
COIL
Power
At Pickup Voltage
196 mW
(typical)
Max. Continuous
1.7 W at 20C (68F) ambient
Dissipation
Temperature Rise
26C (47F) at nominal coil voltage
Max. Temperature
130C (266F)
NOTES
1. All values at 20C (68F).
2. Relay may pull in with less than "Must Operate" value.
3. Specifications subject to change without notice.
2004-09-27
ZETTLER
electronics GmbH
Fax +49 89 800 97 200 www.ZETTLERelectronics.com
office@ZETTLERelectronics.com
0
97
800
89
+49
Tel.
Germany
Puchheim,
D-82178
Junkersstrasse 3,
AZ762
MECHANICAL DATA
[5.04]
.198
[5.04]
.198
[15.12]
.595
[2.5]
.098
* Not used on 1 Form A relay
[ 1.3]
[2.5]
.098
.198
[5.04]
.198
[5.04]
[15.12]
[7.5]
6 x .035
[0.9]
[7.5]
6 x .050
6 x .020
[0.5]
.098
[2.5]
.595
.295
2 x .024
[ 0.6]
.295
2
1
3
6
4
7
5
8
2
1
4
7
5
8
*
*
[ 1.0]
2 x .040
[29.3]
1.155 Max.
[13.0]
.512 Max.
[0.3]
.012
[16.0]
.63 Max.
[3.6]
.142
PC BOARD LAYOUT
WIRING DIAGRAMS
1 Form C
1 Form A
Viewed toward terminals
Viewed toward terminals
Dimensions in inches with metric equivalents in parentheses. Tolerance: .010"
RELAY ORDERING DATA
COIL SPECIFICATIONS DC COIL
ORDER NUMBER*
Nominal Coil
Must Operate
Max. Continuous
Coil Resistance
1 Form C
1 Form A
VDC
VDC
VDC
Ohm 10%
5
3.5
10.2
62 AZ7621A5D
AZ7621C5D
6
4.2
12.3
90
AZ7621A6D
AZ7621C6D
9
6.3
18.3
200
AZ7621A9D
AZ7621C9D
12
8.4
24.7
360 AZ7621A12D
AZ7621C12D
18
12.6
37.0
810
AZ7621A18D
AZ7621C18D
24
16.8
49.4
1,440 AZ7621A24D
AZ7621C24D
48
33.6
98.0
5,760
AZ7621A48D
AZ7621C48D
60
42.0
112.9
7,500
AZ7621A60D
AZ7621C60D
110
77.0
206.9
25,200
AZ7621A110D
AZ7621C110D
* "1A" or "1C" denote silver cadmium oxide contacts.
Substitute "1B" in place of "1A" for 1 Form B contact.
Add suffix "E" to "1A" or "1B" or "1C" for silver tin oxide contacts.
Add suffix "B" to "1A" or "1B" or "1C" for silver nickel contacts.
Add suffix "E" at the end of order number for sealed version.
Add suffix "A" at the end of order number for gold plated contacts.
PDF 
ZIP